共找到 361 条与 化学实验室、实验室设备 相关的标准,共 25 页
Laboratory furniture - Fume cupboards - Part 4: Fume cupboards for pharmacies
Laboratory glassware - Density hydrometers - Part 1: General requirements
Laboratory furniture - Fume cupboards - Part 3: Opposite-sided sash fume cupboards
This method may be used to validate the performance of a specific TGA apparatus. This method may be used to validate the performance of a specific method based upon a TGA mass loss or residue measurement. This method may be used to determine the repeatability of a specific apparatus, operator or laboratory. This method may be used for specification and regulatory compliance purposes.1.1 This method provides procedures for validating mass loss and residue measurements by thermogravimetric analyzers (TGA) and analytical methods based upon the measurement of mass loss or residue content. Performance parameters determined include mass loss and residue repeatability (precision), detection limit, quantitation limit, linearity and bias. 1.2 Validation of apparatus performance and analytical methods is requested or required for quality initiatives or where results may be used for legal purposes. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 There is no ISO standard equivalent to this method. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Mass Loss and Residue Measurement Validation of Thermogravimetric Analyzers
Laboratory fume cupboards - Threshold for confinement test.
This guide provides criteria for evaluating the capability of a laboratory to properly perform commercial cooking appliance energy consumption and cooking-energy efficiency evaluations, and to establish essential characteristics pertaining to the organization, personnel, facilities, and quality systems of the laboratory. 1.1 The scope of this guide includes the laboratory and organizational requirements to test commercial cooking and warming appliances (for example, griddles, fryers, ovens, steam cookers, and hot food holding cabinets) for preheat energy consumption and time, idle energy rate, cooking-energy efficiency, and production capacity, in accordance with the appropriate ASTM test methods under the jurisdiction of Committee F26, including the following:
Standard Guide for Laboratory Requirements Necessary to Test Commercial Cooking and Warming Appliances to ASTM Test Methods
Guide for Laboratory Requirements Necessary to Test Commercial Cooking Appliances to ASTM Test Methods
本规范规定了石油化工中心化验室设计的一般规定、化验室的组成及布置、分析仪器和设备配置原则、化验室管道设计以及中心化验室的土建、采暖通风及空气调节、给排水、电气、电信及信息管理系统、仪表等方面的设计要求。 本规范适用于新建石油化工中心化验室的设计。改建、扩建的中心化验室及装置化验室可参照执行。
Specification for design of central laboratory in petrochemical industry
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-081: Particular requirements for automatic and semi-automatic laboratory equipment for analysis and o
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-081: Particular requirements for automatic and semi-automatic laboratory equipment for analysis and o
This European Standard is a product specification, giving minimum performance requirements for non plumbed-in emergency safety body showers. It is applicable to body showers filled with a washing fluid by the manufacturer and to empty devices to be filled prior to putting into service. Both variations are for first aid use when the body or parts of the body have been exposed to harmful substances or heat. Requirements are also given concerning labelling, marking and information to be supplied by the manufacturer. Throughout this standard, the term "non plumbed-in emergency safety body shower" is referred to as "body shower".
Emergency safety showers - Part 3: Non plumbed-in body showers; English version of DIN EN 15154-3:2009-07
This European Standard is a product specification, giving minimum performance requirements for non plumbed-in emergency safety eyewash units. It is applicable to non plumbed-in emergency safety eyewash units filled with a rinsing fluid by the manufacturer for first aid use when the eyes have been exposed to harmful substances. Requirements are also given concerning labelling, marking and information to be supplied by the manufacturer. Throughout this standard, the term "non plumbed-in emergency safety eyewash unit" is referred to as "eyewash unit".
Emergency safety showers - Part 4: Non plumbed-in eyewash units; English version of DIN EN 15154-4:2009-07
Emergency safety showers - Part 4: Non plumbed-in eyewash units
Emergency safety showers - Part 3: Non plumbed-in body showers
The document specifies requirements for body showers intended to flush contaminated or burning people with sufficient amount of water and is applicable for body showers in internal and external production places.
Emergency safety showers - Part 3: Body showers for production and logistic sites
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-020: Particular requirements for laboratory centrifuges (Second Edition)
General Requirements for Accreditation Bodies Accrediting Environmental Laboratories
1.1 Polarimeters and polariscopes used for measuring stress in glass are described in Test Methods F218, C148, and C978. These instruments include a light source and several optical elements (polarizers, optical retarders, filters, and so forth) that require occasional cleaning, realigning, and calibration. The objective of these practices is to describe the calibration and verification procedures required to maintain these instruments in calibration and ensure that the optical setup is within specification for satisfactory measurements. 1.2 It is mandatory throughout these practices that both verification and calibration are carried out by qualified personnel who fully understand the concepts used in measurements of stress retardation and are experienced in the practices of measuring procedures described in Test Methods F218, C148, and C978. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Standard Practices for Verification and Calibration of Polarimeters
General Requirements for Environmental Proficiency Test Providers
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号