71.080.10 脂族烃 标准查询与下载

SH/T 1493-2015 碳四烯烃中微量羰基化合物含量的测定 分光光度法

本标准规定了用分光光度法测定碳四烯烃中微量羰基化合物的含量。 本标准适用于1-丁烯和1，3-丁二烯中微量羰基化合物含量的测定，最小检测浓度为0.5 mg/kg（以丁酮计）。本标准不适用于异丁烯的测定。

C₄ Olefins.Determination of trace carbonyls.Spectrophotometric method

SH/T 1782-2015 工业用异戊二烯纯度和烃类杂质含量的测定 气相色谱法

本标准规定了用气相色谱法测定工业用异戊二烯纯度和烃类杂质含量。 本标准适用于工业用异戊二烯纯度和烃类杂质含量的测定，其杂质最低检测浓度为0.005%（质量分数）。

Isoprene for industrial use.Determination of purity and hydrocarbon impurities.Gas chromatographic method

SH/T 1789-2015 工业用裂解碳五

本标准规定了乙烯裂解装置分离的工业用裂解碳五的产品分类、要求、检验规则及标志、包装、运输和贮存、安全。 本标准所属产品主要用作生产碳五石油树脂以及提取异戊二烯、间戊二烯、双环戊二烯和异戊烯等产品的原料。

Cracking C₅ fraction for industrial use

SH/T 1791-2015 工业用间戊二烯

本标准规定了工业用间戊二烯的要求、检验规则及标志、包装、运输与贮存、安全。 本标准适用于以石油裂解制乙烯过程中的裂解碳五为原料，经精馏、萃取蒸馏而制得的间戊二烯产品。 化学名称：1，3-戊二烯(1，3-Pentadiene)，包括反-1，3-戊二烯（trans-1，3- Pentadiene）和顺-1,3-戊二烯(cis-1，3-Pentadiene)，也称间戊二烯(Piperylene)。 结构简式：CHCH=CHCH=CH 分子式：CH 相对分子质量：68.117（按2011年国际相对原子质量）

Piperylene for industrial use.Specification

SH/T 1798-2015 工业用1-己烯纯度及烃类杂质的测定 气相色谱法

本标准规定了用气相色谱法测定工业用1-己烯纯度和烃类杂质的方法。 本标准适用于纯度不低于97. 0%（质量分数）以及正己烷、3-己烯、2-己烯、2-甲基-1-戊烯等烃类杂质含量不低于0. 005%（质量分数）的工业用1-己烯的测定。

1-Hexene for industrial use.Determination of purity and hydrocarbon impurities.Gas chromatographic method

SH/T 1785-2015 工业用异戊烯

本标准规定了工业用异戊烯的产品分类、要求、检验规则、标志、包装、运输和储存、安全。 本标准适用于以碳五馏分为原料，经醚化、醚解反应、精馏而制得的异戊烯产品。异戊烯包括2-甲基-1-丁烯和2-甲基-2-丁烯。 结构简式：CH=C(CH)CHCH和CHC(CH)=CHCH。 分子式：CH 相对分子质量：70.135（按2011年国际相对原子质量）

Isoamylene for industrial use.Specification

SH/T 1797-2015 工业用1-己烯

本标准规定了工业用1-己烯的要求、试验方法、检验规则、标志、包装、运输、贮存和安全。 该产品主要用做生产聚乙烯树脂时的共聚单体。 分子结构式：CH=CHCHCHCHCH 相对分子质量：84.159（按2011年国际相对原子质量）。

1-Hexene for industrial use

ASTM D5248-04(2015) 回收的1,1,2-三氯1,2,2-三氟乙烷的标准规范

1.1 This specification covers the three grades of 1,1,2trichloro 1,2,2-trifluoroethane2 typically needed in various industries. It may be used as a reference document by purchasers or by persons establishing in-house, 1,1,2-trichloro 1,2,2trifluoroethane recovery programs.

Standard Specification for Reclaimed 1,1,2-Trichloro 1,2,2-Trifluoroethane

ASTM D7862-15a 与作为汽车火花点火式发动机燃料使用的汽油混合用丁醇的标准规格

1.1 This specification covers butanol intended to be blended with gasoline at 18201;% to 12.58201;% by volume for use as an automotive spark-ignition engine fuel. 1.1.1 Butanol contains 228201;% by mass oxygen. The mass percent of oxygen of a butanol blend with gasoline depends on the volume percent of butanol blended, the density of the butanol isomer, and the density of the base blendstock. 1.1.2 The maximum limit on blending is not a performance limit but a current regulatory limit in the United States. 1.2 This specification covers three butanol isomers:1-butanol, 2-butanol, and 2-methyl-1-propanol. This specification specifically excludes 2-methyl-2-propanol (that is, tert-butyl alcohol). 1.2.1 Tert-butyl alcohol has different physical properties (melting point, water miscibility) than the other three isomers. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel

GOST 24975.1-2015 乙烯和丙烯.色谱分析法

Ethylene and propylene. Chromatographic methods of analysis

GOST 24975.0-2015 乙烯和丙烯. 取样方法

Ethylene and propylene. Methods of sampling

GSO ASTM D2593:2014 使用气相色谱装置测定丁二烯和烃类杂质纯度的方法

1.1 This test method covers the determination of butadiene-1,3 purity and impurities such as propane, propylene, isobutane, n-butane, butene-1, isobutylene, propadiene, trans-butene-2, cis -butene-2, butadiene-1,2, pentadiene-1,4, and, methyl, dimethyl, ethyl, and vinyl acetylene in polymerization grade butadiene by gas chromatography. Impurities including butadiene dimer, carbonyls, inhibitor, and residue are measured by appropriate ASTM procedures and the results used to normalize the component distribution obtained by chromatography. NOTE 1: Other impurities present in commercial butadiene must be calibrated and analyzed. Other impurities were not tested in the cooperative work on this test method. NOTE 2: This test method can be used to check for pentadiene-1,4 and other C5s instead of Test Method D1088. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 6.1 and 9.3.

Standard Test Method for Butadiene Purity and Hydrocarbon Impurities by Gas Chromatography

GSO ASTM D2268:2014 毛细管气相色谱法分析高纯度正庚烷和异辛烷的标准方法

1.1 This test method covers and provides for the analysis of high-purity (greater than 99.5 % by volume) n -heptane and isooctane (2,2,4-trimethylpentane), which are used as primary reference standards in determining the octane number of a fuel. Individual compounds present in concentrations of less than 0.01 % can be detected. Columns specified by this test method may not allow separation of all impurities in reference fuels. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard method for analysis of high - purity n-Hepane and Isooctane by capillary gas chromatography

SH/T 1778-2014 化学级丙烯纯度与烃类杂质的测定 气相色谱法

本标准规定了化学级丙烯纯度和甲烷、乙烷、乙烯、丙烷、环丙烷、异丁烷、正丁烷、丙二烯、乙炔、反-2-丁炼、1-丁烯、异丁烯、顺-2-丁烯、1, 3-丁二烯、甲基乙炔等烃类杂质测定的气相色谱法。本标准适用于纯度不低于90% (体积分数)、杂质含量不低于0.001% (体积分数)的丙烯样品的测定。由于本标准不能测定所有可能存在的杂质,如氢气、氧气、一氧化碳、二氧化碳、水、齐聚物、硫及含氧化合物等,所以要全面表征丙烯样品还需要应用其他的试验方法。

Chemical grade propylene.Determination of purity and hydrocarbon impurities.Gas chromatographic method

SH/T 1777-2014 化学级丙烯

本标准规定了化学级丙烯的要求、检验规则、包装、标志、运输、贮存及安全要求。本标准适用于由炼厂气经脱硫、分离,或以加氢尾油、石脑油或煤、柴油为原料,经管式裂解炉裂解,深冷分离而制得的丙烯产品。该产品用作有机合成的原料。分子式:CH。相对分子质量:42. 081 (按2007年国际相对原子质量)。

Chemical grade propylene

SH/T 1776-2014 工业用乙烯、丙烯中微量氯的测定 微库仑法

本标准规定了工业用乙烯、丙烯中微量氯测定的微库仑法。本标准适用于氯含量不低于1. 0 mg/kg的工业用乙烯、丙烯的测定。本标准并不是旨在说明与其使用有关的所有安全问题。使用者有责任采取适当的安全与健康措施,保证符合国家有关法规的规定。

Ethylene and propylene for industrial use.Determination of trace chlorine.Microcoulometric method

KS M ISO 7382-2013 工业用乙烯 液相和气相取样

Ethylene for industrial use－Sampling in the liquid and the gaseous phase

KS M 1680-2013 工业用丙烯

Propylene for industrial use

KS M 1053-2013 高纯度十三烷

High purity tridecane

KS M 1050-2013 高纯度辛烷值

High purity octane