77.040.20 金属材料无损检测 标准查询与下载

ASTM E3024/E3024M-22 一般工业用磁粉检测的标准实施规程

Standard Practice for Magnetic Particle Testing for General Industry

ISO/FDIS 4993:2022 钢和铁铸件 射线检测

Steel and iron castings — Radiographic testing

T/CSTM 00821-2022 民用飞机超声检测、涡流检测用金属对比试块

本文件规定了民用飞机超声检测和涡流检测方法用金属对比试块的术语和定义、分类、一般要求、 设计、制作、标识和使用及维护。 本文件适用于民用飞机工程设计部门设计、制作及使用维护超声检测、涡流检测金属对比试块。民用飞机机体供应商、零部件制造商、航线运营公司或民航维修单位也可参考使用。

Metallic reference blocks of ultrasonic testing and eddy current testing for civil aircraft

KS B 0817-2021 用脉冲回波技术对金属进行超声波检测的一般规则

General rules for ultrasonic testing of metals by pulse echo technique

T/CASEI 004-2021 承压设备无损检测报告编制规范

1.检测报告的基本结构、编号、格式等方面的要求； 2.检测报告的封面、声明页、首页、续页、附件页等基本框架做出规定； 3.检测报告编号原则，编制审核批准， 印章加盖 ,检测报告结果异常，信息化管理、隐私、所有权保护，报告具体内容等方面做出规定； 4.附录中给出样表，供使用。

Specifications for compiling pressure equipment NDT reports

T/SHSBJL 2-2021 石化用机泵机械精度检验

1、监理工程师基本要求和石化用机泵机械精度检验仪器及装备 2、石化用机泵机械精度检验基本要领 3、石化用机泵机械精度检验要求 4、石化用机泵机械精度检验结果评价

Mechanical accuracy inspection of petrochemical pumps

YB/T 4932-2021 热轧型钢磁粉检测方法

Magnetic particle testing method for hot-rolled steel

ASTM E1571-21 铁磁性钢丝绳电磁检验的标准实施规程

1.1 This practice covers the application and standardization of instruments that use the electromagnetic, the magnetic flux, and the magnetic flux leakage examination method to detect flaws and changes in metallic cross-sectional areas in ferromagnetic wire rope products. 1.1.1 This practice includes rope diameters up to 2.5 in. (63.5 mm). Larger diameters may be included, subject to agreement by the users of this practice. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Electromagnetic Examination of Ferromagnetic Steel Wire Rope

ASTM E272-21 高强度铜基和镍铜合金铸件的标准参考射线照片

1.1 These reference radiographs illustrate various categories, types, and severity levels of discontinuities occurring in high-strength copper-base, nickel-copper, and related alloy castings. The reference radiograph films are an adjunct to this document and must be purchased separately from ASTM International, if needed (see 2.3). Categories and severity levels for each discontinuity type represented by these reference radiographs are described in 1.2. NOTE 1—The basis of application for these reference radiographs requires a prior purchaser supplier agreement of radiographic examination attributes and classification criterion described in Sections 4, 7, 8, 9, and 10 of this standard. 1.2 These reference radiographs consist of forty-five 5 by 7 in. (127 by 178 mm) nominal size reproductions (20 made from 1 in. (25.4 mm) plate castings exposed with low voltage X-rays for thicknesses up to and including 2 in.) and 25 made from 3 in. (76 mm) plate castings exposed with 2 MV X-rays or Cobalt 60 isotope for thicknesses greater than 2 in. up to and including 6 in. Unless otherwise specified in a purchaser supplier agreement (see 1.1), each discontinuity category is for comparison only with production radiographs produced with radiation energy levels within the thickness range covered by the category. These reference radiographs illustrate discontinuities in sand-cast manganese-nickel-aluminum bronze-alloy plates and are representative of those found in narrow freezing range (formerly “high shrinkage”), high-strength copper and nickel-copper alloys. Following is a list of discontinuity categories, types, and severity levels for the adjunct reference radiographs of this standard (see Note 2): 1.2.1 Category A—Gas porosity; severity levels 1 through 5 for two thickness ranges. 1.2.1.1 AX—Up to and including 2 in. (50.8 mm) (called “Code A Discontinuity type” in previous revisions). 1.2.1.2 AG—Greater than 2 in. (50.8 mm) up to and including 6 in. (152.4 mm) (called “Code A Discontinuity type” in previous revisions). 1.2.2 Category B—Inclusions. 1.2.2.1 Ba—Sand inclusions, severity levels 1 through 5 for two thickness ranges. (1) BaX—Up to and including 2 in. (50.8 mm) (called “Code Ba Discontinuity type” in previous revisions). (2) BaG—Greater than 2 in. (50.8 mm) up to and including 6 in. (152.4 mm) (called “Code Ba Discontinuity type” in previous revisions). 1.2.2.2 Bb—Dross inclusions, severity levels 1 through 5 for two thickness ranges. (1) BbX—Up to and including 2 in. (50.8 mm) (called “Code Bb Discontinuity type” in previous revisions). (2) BbG—greater than 2 in. (50.8 mm) up to and including 6 in. (152.4 mm) (called “Code Bb Discontinuity type” in previous revisions). 1.2.3 Category C—Shrinkage; three types 1.2.3.1 Ca—linear shrinkage, severity levels 1 through 5 for thicknesses 2 in. up to and including 6 in. (50.8 to 152.4 mm). 1.2.3.2 Cb—feathery shrinkage, severity levels 1 through 5 for thicknesses up to and including 2 in. (50.8 mm). (Called “Cd feathery shrinkage” in previous revisions.) 1.2.3.3 Cc—spongy shrinkage, severity levels 1 through 5 for thicknesses 2 in. up to and including 6 in. (50.8 to 152.4 mm) (called “Cd spongy shrinkage” in previous revisions). NOTE 2—Discontinuity classes designated with a subscript “X” were produced with low energy X-ray radiation; discontinuity classes designated with subscript “G” were produced with Cobalt 60 or 2 MV X-rays, or both, and are the same reference radiographs and thickness ranges used in previous editions of this standard. Section 4 details the significance and use of these reference radiographs. 1.3 From time to time, there may be minor changes to the process for manufacturing of the reference radiograph adjunct materials. These changes could include changes in the films or processing chemicals used, changes in the dies or printing for the cardboard mats, etc.; however, in all cases, these changes are reviewed by the Illustration Monitoring Subcommittee and all reference radiographs are reviewed against a fixed prototype 1 These reference radiographs are under the jurisdiction of ASTM Committee E07 on Nondestructive Testing and are the direct responsibility of Subcommittee E07.02 on Reference Radiological Images. Current edition approved Nov. 1, 2021. Published November 2021. Originally approved in 1965. Last previous edition approved in 2019 as E272 – 19. DOI: 10.1520/E0272-21. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 8QLYHUVLW\RI7RURQWR 8QLYHUVLW\RI7RURQWR SXUVXDQWWR/LFHQVH$JUHHPHQW1RIXUWKHUUHSURGXFWLRQVDXWKRUL]HG 'RZQORDGHGSULQWHGE\ &RS\ULJKWE\$670,QW O DOOULJKWVUHVHUYHG :HG'HF*07 image to ensure that there are no changes to the acceptance level represented by the reference radiographs. Therefore, the adjunct reference radiographs remain valid for use with this standard regardless of the date of production or the revision level of the text standard. 1.4 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Reference Radiographs for High-Strength Copper-Base and Nickel-Copper Alloy Castings

ASTM E802-21 小于等于4英寸的灰铸铁件的标准参考射线照片 （114毫米）厚

1.1 These reference radiographs for gray iron castings consist of one set of illustrations of centerline shrinkage with severity levels 1 to 5 using three radiation source types as follows: 1.1.1 Volume I: Medium Voltage (Nominal 250 kVp) X-ray Reference Radiographs—Set of 5 severity levels in a 15 by 17 in. folder. 1.1.2 Volume II: Iridium-192 Reference Radiographs—Set of 5 severity levels in a 15 by 17 in. folder. 1.1.3 Volume III: Cobalt-60 Reference Radiographs—Set of 5 severity levels in a 15 by 17 in. folder. NOTE 1—The reference radiograph films are an adjunct to this document and must be purchased separately from ASTM International if needed. 1.2 From time to time, there may be minor changes to the process for manufacturing of the reference radiograph adjunct materials. These changes could include changes in the films or processing chemicals used, changes in the dies or printing for the cardboard mats, etc.; however, in all cases, these changes are reviewed by the Illustration Monitoring Subcommittee and all reference radiographs are reviewed against a fixed prototype image to ensure that there are no changes to the acceptance level represented by the reference radiographs. Therefore, the adjunct reference radiographs remain valid for use with this standard regardless of the date of production or the revision level of the text standard. 1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Reference Radiographs for Gray Iron Castings Up to 412 in. (114 mm) in Thickness

ASTM E1444/E1444M-21 航空航天用磁粉检验的标准实施规程

1.1 This practice establishes minimum requirements for magnetic particle testing used for the detection of surface or slightly subsurface discontinuities in ferromagnetic material. This practice is intended for aerospace applications using the wet fluorescent method. Refer to Practice E3024/E3024M for industrial applications. Guide E709 can be used in conjunction with this practice as a tutorial. NOTE 1—This practice replaces MIL-STD-1949. 1.2 The magnetic particle testing method is used to detect cracks, laps, seams, inclusions, and other discontinuities on or near the surface of ferromagnetic materials. Magnetic particle testing may be applied to raw material, billets, finished and semi-finished materials, welds, and in-service parts. Magnetic particle testing is not applicable to non-ferromagnetic metals and alloys such as austenitic stainless steels. See Appendix X1 for additional information. 1.3 Portable battery powered electromagnetic yokes are outside the scope of this practice. 1.4 All areas of this practice may be open to agreement between the cognizant engineering organization and the supplier, or specific direction from the cognizant engineering organization. 1.5 This standard is a combined standard, an ASTM standard in which rationalized SI units and inch-pound units are included in the same standard, with each system of units to be regarded separately as standard. 1.5.1 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Magnetic Particle Testing for Aerospace

EC 1-2021 UNI 11479-2021 无损检测 钢灯柱和交通信号灯养护状况调查技术

Non-destructive testing - Techniques of investigation on the state of conservation of steel lighting columns and traffic lights

ASTM E709-21 磁粉检验的标准指南

1.1?This guide2 covers techniques for both dry and wet magnetic particle testing, a nondestructive method for detecting cracks and other discontinuities at or near the surface in ferromagnetic materials. Magnetic particle testing may be applied to raw material, semifinished mate

Standard Guide for Magnetic Particle Testing

KS B 0544-2021 鉴定程序FOR技术标准超声波探伤和铝铝合金焊缝

Standard qualification procedure for ultrasonic testing technique of aluminium and aluminium alloy welds

KS B 0536-2021 用于测量厚度的方法式超声波脉冲回波技术

Measurement of thickness by ultrasonic pulse-echo technique

T/CSAA 2-2020 薄壁零件残余应力检测方法

4 检测原理及方法　 4.1 X射线应力检测　 4.2 超声应力检测　 5 一般要求　 5.1 人员　 5.2 应力检测系统　 5.3 环境　 6 样品　  6.1 样品的要求及表面处理　 6.2 样品的切割　 6.3 样品的剥层处理　 6.4 样品的标记　 7 检测流程和实施　 7.1 残余应力检测流程　 7.2 检测方法选择　 7.3 检测条件和参数选取　 7.4 检测系统检定或校准　 7.5 检测环境确认　 7.6 残余应力检测　 7.7 检测数据处理和计算　 7.8 结果统计和分析　 8 检测报告　 附录A (规范性) 应力参考样品及设备检定　 附录B (资料性) 零件的残余应力检测评价及调控　 附录C (资料性) 残余应力检测报告　

Test method for residual stress analysis on thin wall parts

T/CIRA 14-2020 管道焊缝X射线数字成像检测方法

本文件的制定主要根据国内外管道射线数字成像技术的研究和应用现状、典型应用案例、使用经验及发展趋势，并参考了 《中华人民共和国石油天然气行业标准》SY/T4109-2013、《承压设备无损检测》NB／T 47013-2015 ，文件主要内容如下：范围，规范性引用文件，术语和定义，基本要求，检测方法、图像质量评定、数据存储、检测报告。此外，还包括附录A“分辨率测定”。

X-ray digital imaging inspection method for pipeline welds

YB/T 4812-2020 钢板自动超声检测系统综合性能测试方法

Comprehensive performance testing method for steel plate automatic ultrasonic inspection system

YB/T 4811-2020 热轧H型钢超声检测方法

Ultrasonic testing method for hot-rolled H-shaped steel

YB/T 4082-2020 钢管、钢棒自动超声检测系统综合性能测试方法

Comprehensive performance testing method of automatic ultrasonic inspection system for steel pipes and steel rods