77.150.60 铅、锌和锡产品 标准查询与下载

YS/T 1570-2022 栅栏型铅合金包覆铝芯阳极板

本文件适用于以铅合金包覆铝芯为基本材料，以栅栏型结构，按照特定技术和工艺生产的栅栏型铅合金包覆铝芯阳极板。

Fence type lead alloy covered aluminum core anode plate

T/CASME 24-2022 淋浴水龙头主体铸件技术条件

本文件规定了淋浴水龙头主体铸件的技术要求、检验方法、检验规则、标志、包装、运输和贮存。

Technical specifications for main casting of shower faucet

ASTM B1013-22 高流动性（HF）锌铝合金薄壁压铸件标准规范

1.1 This specification covers commercial zinc, zincaluminum castings and continuous cast bar stock, as designated and specified in Table 1. 1.2 Systems of nomenclature used to designate zinc and zinc-aluminum (ZA) alloys used for casting are described in Appendix X1. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for High Fluidity (HF) Zinc-Aluminum Alloy Thin Wall Die Castings

ASTM B240-22 铸造和压铸用锌和锌铝（ZA）合金锭的标准规范

1.1 This specification covers commercial zinc and zincaluminum (ZA) alloys in ingot form for remelting for the manufacture of pressure die castings, foundry castings and continuous cast bar stock as designated and specified in Table 1. Seven alloy compositions are specified, designated as follows: Common Traditional ASTMA UNSA Alloy 3 Zamak 3 AG 40A Z33524 Alloy 7 Zamak 7 AG 40B Z33526 Alloy 5 Zamak 5 AC 41A Z35532 Alloy 2 Zamak 2 AC 43A Z35544 ZA-8 ZA-8 ... Z35637 ZA-12 ZA-12 ... Z35632 ZA-27 ZA-27 ... Z35842 ACuZinc52 ACuZinc5 ... Z46540 A See Table 1, footnote B. 1.2 Zinc alloys Z33524, Z33526, Z35532, Z46540, and Z35544 are used primarily for remelting in the manufacture of pressure die castings. Zinc-aluminum alloys Z35637, Z35632, and Z35842 are used for remelting in the manufacture of both foundry and pressure die castings. Castings made from these ingots are specified in Specification B86, Standard Specification for Zinc and Zinc-Aluminum Alloys for Foundry and Die Castings. 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 Systems of nomenclature used to designate zinc and zinc-aluminum (ZA) alloys used for casting are described in Appendix X1. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloys in Ingot Form for Foundry and Die Castings

YS/T 1439-2021 锌及锌合金牺牲阳极

Zinc and zinc alloy sacrificial anodes

YS/T 310-2021 热镀用锌合金锭

Zinc alloy ingots for hot-dip

YS/T 1457-2021 铅冰铜

lead matte

T/FSYY 0008-2021 再生利用产品 粗碳酸锌

再生利用产品 粗碳酸锌

Recycled products — Crude zinc carbonate

ASTM B792-16(2021) 泥浆铸造用铸锭状锌合金的标准规范

1.1 This specification covers commercial zinc alloys in ingot form for remelting for the manufacture of castings from the alloys as specified and designated as shown in Table 1. 1.2 Slush casting alloys are used primarily for the manufacture of hollow castings such as lighting fixtures, lamp bases, and small statues. 1.3 This specification covers two zinc alloys which are specified and designated as follows: UNS ASTM Z34510 Slush Casting Alloy A Z30500 Slush Casting Alloy B 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zinc Alloys in Ingot Form for Slush Casting

ASTM B240-21 铸造和压铸用锭状锌和锌铝（ZA）合金的标准规范

Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloys in Ingot Form for Foundry and Die Castings

ASTM B997-16(2021) 热浸涂层用铸锭状锌铝合金的标准规范

1.1 This specification covers certain zinc-aluminum (Zn-Al) alloys in ingot form for re-melting for use in the production of hot-dip coatings on steel. Alloy compositions are specified below and in Table 1. ASTM Common UNS Type 5 95/5 Zn/Al Z30507 Type 10 90/10 Zn/Al Z30600 Type 15 85/15 Zn/Al Z30706 NOTE 1—The zinc-aluminum alloys in Specification B997 are intended to be used primarily to create a molten zinc-aluminum bath and differ from the master alloys in Specification B860 which are intended primarily to adjust the concentration of certain elements in molten zinc galvanizing baths. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zinc-Aluminum Alloys in Ingot Form for Hot-Dip Coatings

T/ZZB 2105-2021 汽车工业用高纯锡锭

本文件规定了汽车工业用高纯锡锭的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量证明书、合同（或订货单）内容和质量承诺。 本文件适用于可作为焊料和锡合金等应用于汽车工业中，以火法或电解法精炼所生产的锡锭产品。

High purity tin ingots for automobile industry

T/SACE 017-2020 废催化剂制氧化锌

本文件适用于以炼油、化工、化肥、煤化工等行业产生的以含锌、铜锌为主的有色金属废催化剂为原料，经高温、焙烧、冷凝等工艺后形成的氧化锌。

Zinc Oxide from Spent Catalyst

YS/T 1364-2020 冶炼用副产品硫酸铅

Lead sulfate, a by-product of smelting

YS/T 1351-2020 锌及锌合金线材

Zinc and zinc alloy wire

T/CNIA 0071-2020 高铅渣

本文件规定了高铅渣的产品分类、技术要求、试验方法、检验规则、标志、包装、运输、贮存、质量预报单及订货单（或合同）内容。 本文件适用于铅精矿及铅膏经氧化熔炼（除密闭鼓风炉炼铅（ISP）工艺外）后得到的高铅渣，主要用于生产粗铅。

High lead slag

ASTM B252-92(2020) 用于电镀和转化涂层的锌合金压铸件的制备标准指南

1.1 This guide is intended as an aid in establishing and maintaining a procedure for preparing zinc alloy die castings for electroplating and conversion coatings. It is primarily intended for the preparation of Alloys UNS Z33521 (AG-40A) and UNS Z35530 (AC-41A) (Specification B86) for electroplating with copper, nickel, and chromium (Specification B456). 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Preparation of Zinc Alloy Die Castings for Electroplating and Conversion Coatings

ASTM B23-20 白色金属轴承合金的标准规范

1.1 This specification covers eight typical white metal bearing alloys, in bar or ingot form, known commercially as “babbitt metal.” The alloys are specified, covering the range commercially used, and are designated by the alloy numbers shown in Table 1. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for White Metal Bearing Alloys (Known Commercially as “Babbitt Metal”)

ASTM B749-20 铅和铅合金带 板材和板材产品标准规范

1.1 This specification covers lead sheet, strip, and plate of various alloys intended for use in chemical plants, sound attenuation, roofing, vibration dampening, flashing and weather stripping, waterproofing, and radiation shielding. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Lead and Lead Alloy Strip, Sheet, and Plate Products

ASTM B1013-20 高流动性锌铝合金薄壁压铸件的标准规范

Standard Specification for High Fluidity (HF) Zinc-Aluminum Alloy Thin Wall Die Castings