77.150.60 铅、锌和锡产品 标准查询与下载

ASTM F1182-07(2019) 牺牲锌合金阳极的标准规范

1.1 This specification covers the requirements for zinc anodes in the form of slabs, plates, discs, and rods for corrosion protection (cathodic protection) of metals and alloys. 1.2 The anodes are primarily intended to reduce corrosion of surface ship and submarine hulls, steel and aluminum equipment and structures, sea chests, sonar domes, and the seawater side of condensers and other heat exchangers. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Anodes, Sacrificial Zinc Alloy

YS/T 1343-2019 锌冶炼用氧化锌富集物

Zinc oxide concentrate for zinc smelting

ASTM B29-19 精制铅的标准规格

1.1 This specification covers refined lead in pig, block, or hog form. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Refined Lead

ASTM B952/B952M-19 用于旋转铸锭的锭形式的锌合金的标准规格

1.1 This specification covers zinc alloys in ingot form for remelting for the manufacture of Spin Castings as specified and designated, as shown in Table 1. Seven alloy compositions are specified, designated as follows: Common Traditional UNS Spin Casting Alloy SC-A ... Z35550 Spin Casting Alloy SC-B ... Z35551 Spin Casting Alloy SC-C ... Z35534 Spin Casting Alloy SC-D HJ10 Z35547 Spin Casting Alloy SC-E HJ20 Z35548 Spin Casting Alloy SC-F HJ40 Z35552 ZA-73 ... Z36500 1.2 Zinc alloys #2, #3, #5, and ZA-8 specified in Specification B240 are also used in the spin casting process. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zinc Alloys in Ingot Form for Spin Casting

ASTM B86-18e1 锌和锌 - 铝（ZA）合金铸造和压铸件的标准规范

Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloy Foundry and Die Castings

ASTM B949-18 锌和锌合金产品一般要求的标准规范

1.1 This specification establishes general requirements, unless otherwise specified in the specific product specification, for ordering information, marking, and sampling for chemical analysis common to zinc and zinc alloy products and shall apply to Specifications B6, B69, B86, B240, B327, B418, B750, B792, B793, B833, B852, B860, B892, B894, B897, B907, B943, and B960 to the extent referenced therein. 1.2 Although this specification establishes general requirements, it does not restrict that, by agreement between customer and supplier, these requirements may be altered by a customer to suit individual need. 1.3 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification shall be prescribed in the product specification. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. This applies except where SI units only are specified. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for General Requirements for Zinc and Zinc Alloy Products

ASTM B86-18 锌和锌 - 铝（ZA）合金铸造和压铸件的标准规范

Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloy Foundry and Die Castings

YS/T 1286-2018 粗锌

Coarse zinc

YS/T 1224-2018 超高纯锌

ultra high purity zinc

YS/T 1223-2018 冶炼副产品 铅铊合金锭

Smelting by-product lead-thallium alloy ingots

YS/T 1225-2018 高纯二氧化锡

High purity tin dioxide

YS/T 1221-2018 锡粒

tin pellets

YS/T 1222-2018 锡球

Tin ball

T/ZZB 0253-2017 电容器端面用无铅锡基喷金线

本标准规定电容器端面用无铅锡基喷金线的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输与贮存、合同（或订货单）和质保期限及质量承诺等内容。 本标准适用于金属化薄膜电容器端面用无铅锡基喷金线（简称线材）。

Lead-free tin-based spraying wire for capacitor end face

ASTM B240-17 铸造和压模铸件用铸锭结构中锌和锌铝(ZA)合金的标准规格

1.1 This specification covers commercial zinc and zinc-aluminum (ZA) alloys in ingot form for remelting for the manufacture of pressure die castings, foundry castings and continuous cast bar stock as designated and specified in Table 1. Seven alloy compositions are specified, designated as follows: Common Traditional ASTMA UNSA         Alloy 3 Zamak 3 AG 40A Z33524 Alloy 7 Zamak 7 AG 40B Z33526 Alloy 5 Zamak 5 AC 41A Z35532 Alloy 2 Zamak 2 AC 43A Z35544 ZA-8 ZA-8  ... Z35637 ZA-12 ZA-12

Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloys in Ingot Form for Foundry and Die Castings

YS/T 1113-2016 锌及锌合金棒材和型材

Zinc and zinc alloy rods and profiles

YS/T 1151-2016 锡蒸发料

Tin evaporation material

YS/T 1156-2016 铜铟镓硒靶材

Copper indium gallium selenide target

YS/T 1153-2016 低铁锌锭

Low iron zinc ingot

YS/T 1155-2016 铜铟镓硒合金粉

Copper Indium Gallium Selenium Alloy Powder