77.150.60 铅、锌和锡产品 标准查询与下载

ASTM B997-16e1 热浸镀用铸锭状锌铝合金的标准规范

Standard Specification for Zinc-Aluminum Alloys in Ingot Form for Hot-Dip Coatings

ASTM B792-16 空壳铸件用锭锌合金的标准规格

1.1 This specification covers commercial zinc alloys in ingot form for remelting for the manufacture of castings from the alloys as specified and designated as shown in Table 1. (A) The following applies to all specified limits in this table. For purposes of determining conformance with this specification, the observed or calculated value obtained from analysis shall be rounded off “to the nearest unit” in the last right-hand place of figures used in expressing the specified limit, in accordance with the rounding method of Practice E29.(B) UNS designations were established in accordance with Practice E527.(C) Refer to Practice B908. (Note: Colors indicated are for North American applications.) 1.2 Slush casting alloys are used primarily for the manufacture of hollow castings such as lighting fixtures, lamp bases, and small statues. 1.3 This specification covers two zinc alloys which are specified and designated as follows: UNS ASTM Z34510 Slush Casting Alloy A Z30500 Slush Casting Alloy B 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Zinc Alloys in Ingot Form for Slush Casting

ASTM B997-16 热浸镀用铸锭状锌铝合金的标准规范

1.1 This specification covers certain zinc-aluminum (Zn-Al) alloys in ingot form for re-melting for use in the production of hot-dip coatings on steel. Alloy compositions are specified below and in Table 1. ASTM Common UNS Type 5 95/5 Zn/Al to be assigned Type 10 90/10 Zn/Al to be assigned Type 15 85/15 Zn/Al to be assigned Note 1: The zinc-aluminum alloys in Specification B997 are intended to be used primarily to create a molten zinc-aluminum bath and differ from the master alloys in Specification B860 which are intended primarily to adjust the concentration of certain elements in molten zinc galvanizing baths. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Zinc-Aluminum Alloys in Ingot Form for Hot-Dip Coatings

GOST 18394-2016 镀锡铅锡箔. 规格

Tin plated lead and tin foil. Specifications

YS/T 1093-2015 再生锌原料

本标准规定了再生锌原料的要求、试验方法、检验规则及包装、运输和质量证明书及订货单(或合同)等。 本标准适用于锌冶炼过程和镀锌过程中产生的锌渣，废锌电池，废涂层以及钢铁烟尘等再生锌原料。主要用于回收金属锌及其他有价金属。

Regenerated zinc raw material

YS/T 1089-2015 湿法冶金铜电积用阳极板

本标准规定了湿法冶金铜电积用阳极板(以下简称阳极板)产品的术语和定义、要求、试验方法、检验规则和标志、包装、运输、贮存及质量证明书与订货单(或合同)内容。 本标准适用以铅为基本原料，添加锡、锑、钙、锶等元素，形成不同的合金组分比例，经熔炼、轧制、焊接等工艺生产的适用于湿法冶金铜电积用阳极板。

Anode plate for copper electrowinning in hydrometallurgy

YS/T 1055-2015 硒化锌

本标准规定了硒化锌的要求、试验方法、检验规则及标志、包装、运输、贮存、质量证明书以及订货单(或合同)内容等。 本标准适用于使用99.999%锌和99.999%硒化氢通过化学气相沉积法制备的硒化锌光学材料。

Zinc selenide

YS/T 1091-2015 铅膏

本标准规定了铅膏的要求、试验方法、检验规则、包装、运输、贮存和质量证明书以及订货单(或合同)内容等。 本标准适用于废旧铅酸蓄电池经破碎分选后得到的铅膏，供铅冶炼生产用。

Lead plaster

YS/T 995-2014 湿法冶金电解锌用阳极板

本标准规定了湿法冶金电解锌用阳极板(以下简称阳极板)产品的术语和定义、要求、试验方法、检验规则与标志、包装、运输、贮存及质量证明书和合同(或订货单)内容。本标准适用于以铅为基本原料,添加银、钙、锶及稀土等元素,按照特定配方和工艺生产的湿法电解锌用阳极板。

Anode plate for zinc electrolysis in hydrometallurgy

YS/T 992-2014 铅阳极泥

本标准规定了铅阳极泥的要求、试验方法、检验规则、包装、贮存和质量预报单及合同(或订货单)内容。本标准适用于铅阳极在电解精炼过程中产生的不溶物质,供提炼贵金属及其他有价元素使用。

Lead anode mud

YS/T 996-2014 掺锑二氧化锡

本标准规定了掺锑二氧化锡的要求、试验方法、检验规则及标志、包装、运输、贮存和质量证明书与合同(或订货单)内容。本标准适用于以金属锡或锡的氯化物为原料,经湿法冶金、干燥、焙烧等制得的掺锑二氧化锡,主要用于抗静电塑料、涂料、纤维用防辐射涂层、建筑用节能视窗、太阳能电池、汽车风挡等。

Antimony-doped tin oxide

ASTM B952/B952M-14 旋转铸造用锭锌合金的标准规格

1.1 This specification covers zinc alloys in ingot form for remelting for the manufacture of Spin Castings as specified and designated, as shown in Table 1. Seven alloy compositions are specified, designated as follows: (A) Per Practice B908.(B) For purposes of acceptance and rejection, the observed value or calculated value obtained from analysis should be rounded to the nearest unit in the last right-hand place of figures, used in expressing the specific limit in accordance with the rounding procedure prescribed in Practice E29.(C) ZA-73 is also often used as a pressure die casting alloy.   Common Traditional UNS           Spin Casting Alloy SC-A ... Z35550   Spin Casting Alloy SC-B ... Z35551   Spin Casting Alloy SC-C ... Z35534   Spin Casting Alloy SC-D HJ10 Z35547   Spin Casting Alloy SC-E HJ20

Standard Specification for Zinc Alloys in Ingot Form for Spin Casting

ASTM B749-14 铅和铅合金带材, 薄板材和厚板材产品的标准规格

1.1 This specification covers lead sheet, strip, and plate of various alloys intended for use in chemical plants, sound attenuation, roofing, vibration dampening, flashing and weather stripping, waterproofing, and radiation shielding. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Lead and Lead Alloy Strip, Sheet, and Plate Products

ASTM B29-14 精炼铅的标准规格

1.1 This specification covers refined lead in pig, block, or hog form. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Refined Lead

YS/T 71-2013 粗铅

本标准规定了粗铅的要求、试验方法、检验规则和标志、包装、运输、贮存及质量证明书与合同(或订货单)内容。本标准适用于冶金炉熔炼所生产的粗铅。

Wet lead

YS/T 920-2013 高纯锌

本标准规定了高纯锌的要求、试验方法、检验规则及包装、标志、运输、贮存、质量证明书和合同(或订货单)内容。本标准适用于以99.995%、99.99%的锌为原料,用真空蒸馏法工艺而生产的高纯锌。高纯锌产品主要应用于制备半导体化合物、红外发光材料、高级合金等。高纯锌粒与高纯锌粉可用作化学试剂等。

High purity zinc

YS/T 915-2013 蓄电池板栅用铅锑合金锭

本标准规定了蓄电池板栅用铅锑合金锭(以下简称铅锑合金锭)的要求、试验方法、检验规则、标志、包装、运输、贮存和质量证明书以及合同(或订货单)内容等。本标准适用于蓄电池板栅用铅锑合金锭。

The lead antimony alloys ingot for the accumulator cell slab lattice

YS/T 866-2013 电容器端面用无铅锡基喷金线

本标准规定了电容器端面用无铅锡基喷金线的术语、要求、试验方法、检验规则、标志、包装、运输与贮存和质量证明书、合同(或订货单)等内容、本标准适用于金属化薄膜电容器端面用无铅锡基喷金线(以下简称线材)、

Lead-free tin-based spraying wire for capacitor end face

YS/T 44-2011 高纯锡

本标准规定了高纯锡的要求、试验方法、检验规则和标志、包装、运输、贮存、质量证明书以及合同（或订货单）内容。 本标准适用于以含锡99.90%及以上的精锡为原料经电解等工艺制得的纯度不小于99.999%的锡；以Sn-05锡为原料经直拉单晶提纯等工艺制得的纯度不小于99.999 9%及99.999 99%的锡。产品供制备高纯合金、化合物半导体、超导材料、焊料以及化合物半导体的掺杂剂、氧化铟锡靶材（ITO）等。

High-purity tin

YS/T 523-2011 锡、铅及其合金箔和锌箔

本标准规定了加工锡、铅及其合金箔和锌箔的要求、试验方法和检验规则、标志、包装、运输和贮存及质量证明书和合同（或订货单）等内容。 本标准适用于电气、仪表、医疗器械等工艺部门制造零件使用的锡、铅及其合金箔和锌箔。

Tin and tin alloy foil-lead and lead alloy foil-zinc foil