共找到 227 条与 铅、锌和锡产品 相关的标准,共 16 页
Lead and lead alloys - Rolled lead sheet for building purposes
This European Standard specifies the designation, the requirements for chemical composition, surface condition and dimensional tolerances for rolled lead sheet. Lead sheet covered by this European standard is made by the roll deformation process and is intended for roofs, flashings, weatherings, claddings, pre-formed panels, damp-proof courses and similar building work. No requirements for supporting construction, design of roof or cladding systems and methods of joining are included.
Lead and lead alloys — Rolled lead sheet for building purposes
This International Standard specifies the designation, chemical composition, marking and other requirements for zinc alloy castings, produced by pressure die, permanent mould or sand casting, or another casting process.
Zinc and zinc alloys - Castings - Specifications
JIS H 4301: 1993を,次のように改正する。
Lead and lead alloy sheets and plates (Amendment 1)
JIS H 4311 : 1993を,次のように改正する。
Lead and lead alloy tubes for common industries (Amendment 1)
This European Standard specifies the designation, the requirements for chemical composition, surface condition and dimensional tolerances for rolled lead sheet. Lead sheet covered by this European standard is made by the roll deformation process and is intended for roofs, flashings, weatherings, claddings, pre-formed panels, damp-proof courses and similar building work.No requirements for supporting construction, design of roof or cladding systems and methods of joining are included.
Lead and lead alloys - Rolled lead sheet for building purposes
The standard specifies the designation, the requirements for chemical composition, surface condition and dimensional tolerances for rolled lead sheet. Lead sheet covered by this document is made by the roll deformation process and is intended for general purposes i.e. chemical process equipment construction. NOTE Rolled lead sheet for building purposes are specified in DIN EN 12588.
Lead and lead alloys - Rolled lead sheet for general purposes
Lead and lead alloys. Lead and lead alloy sheaths and sleeves of electric cables
This European Standard specifies the designation, chemical compositions and other requirements for lead and lead alloy electric cable sheaths and sleeves.#,,#
Lead and lead alloys - Lead and lead alloy sheaths and sleeves of electric cables; German version EN 50307:2002
1.1 This specification covers refined lead in pig, block, or hog form.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
Standard Specification for Refined Lead
Lead and lead alloys - Lead and lead alloy sheaths and sleeves of electric cables
Lead and lead alloys - Lead oxides
This part of EN 1559 applies to castings made from zinc alloys produced by sand casting, permanent mould casting, pressure die casting, centrifugal casting, continuous casting or investment casting.
Founding - Technical conditions of delivery - Part 6: Additional requirements for zinc alloy castings
This specification covers a zinc molybdate primer in the form of a liquid. This product has been used typically as a protective coating on metals, but usage is not limited to such applications.
Primer Zinc Molybdate
Standard Specification for Zinc Alloys in Ingot Form for Slush Casting
Standard Specification for Zinc - Copper - Aluminum in Ingot Form for Die Castings
This specification covers a commercial zinc-copper-aluminum alloy in ingot form (UNS Z46540 ) for remelting for the manufacture of die castings. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
Specification for Zinc-Copper-Aluminum in Ingot Form for Die Castings
This specification covers commercial zinc alloys in ingot form for remelting for the manufacture of castings from the alloys as specified and designated as shown in .Slush casting alloys are used primarily for the manufacture of hollow castings such as lighting fixtures, lamp bases, and small statues. This specification covers two zinc alloys which are specified and designated as follows: The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
Specification for Zinc Alloys in Ingot Form for Slush Casting
This specification covers commercial zinc and zinc-aluminum (ZA) alloys in ingot form for remelting for the manufacture of pressure die castings and foundry castings as designated and specified in Table 1. Seven alloy compositions are specified, designated as follows: UNSA ASTMA Common Z33521 AG 40A Alloy 3 Z33522 AG 40B Alloy 7 Z35530 AC 41A Alloy 5 Z35540 AC 43A Alloy 2 Z35635 ZA-8 Z35630 ZA-12 Z35840 ZA-27 . Zinc alloys Z33521, Z33522, Z35530, and Z35540 are used primarily for remelting in the manufacture of pressure die castings. Zinc-aluminum alloys Z35635, Z35630, and Z35840 are used for remelting in the manufacture of both foundry and pressure die castings. Castings made from these ingots are specified in ASTM B86, Standard Specification for Zinc and Zinc-Aluminum Alloys for Foundry and Die Castings. The values stated in inch-pound units are to be regarded as standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
Specification for Zinc Alloys in Ingot Form for Die Castings
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号