81.060.20 陶瓷制品 标准查询与下载

DB5110/T 4001-2023 白酒贮藏容器 陶坛

Liquor storage container pottery altar

DB5103/T 4001-2023 白酒贮藏容器 陶坛

本文件适用于贮藏白酒用的陶坛产品。

Liquor storage container pottery altar

DB5105/T 4001-2023 白酒贮藏容器 陶坛

Liquor storage container pottery altar

DB5115/T 4001-2023 白酒贮藏容器 陶坛

于贮藏白酒用的陶坛产品

Liquor storage container pottery altar

ASTM C373-18(2023) 用真空法测定压制瓷砖和玻璃砖的吸水性和相关财产的标准试验方法 以及用煮沸法测定挤压瓷砖和非烧结陶瓷洁具产品的吸水性及相关性能

1.1 These test methods covers procedures for determining water absorption, bulk density, apparent porosity, and apparent specific gravity of non-tile fired unglazed ceramic whiteware2 products, glazed or unglazed ceramic tiles, and glass tiles. 1.2 The values stated in metric units are normative. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not normative. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Determination of Water Absorption and Associated Properties by Vacuum Method for Pressed Ceramic Tiles and Glass Tiles and Boil Method for Extruded Ceramic Tiles and Non-tile

ASTM C674-13(2023) 陶瓷洁具材料弯曲财产的标准试验方法

1.1 These test methods cover determination of the modulus of rupture and the modulus of elasticity of fired ceramic whitewares bodies, formed by any fabrication method, and are applicable to both glazed and unglazed test specimens. 1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Flexural Properties of Ceramic Whiteware Materials

ASTM C1161-18(2023) 环境温度下高级陶瓷抗弯强度的标准试验方法

1.1 This test method covers the determination of flexural strength of advanced ceramic materials at ambient temperature. Four-point-1⁄4-point and three-point loadings with prescribed spans are the standard as shown in Fig. 1. Rectangular specimens of prescribed cross-section sizes are used with specified features in prescribed specimen-fixture combinations. Test specimens may be 3 by 4 by 45 to 50 mm in size that are tested on 40-mm outer span four-point or three-point fixtures. Alternatively, test specimens and fixture spans half or twice these sizes may be used. The method permits testing of machined or as-fired test specimens. Several options for machining preparation are included: application matched machining, customary procedure, or a specified standard procedure. This method describes the apparatus, specimen requirements, test procedure, calculations, and reporting requirements. The test method is applicable to monolithic or particulateor whisker-reinforced ceramics. It may also be used for glasses. It is not applicable to continuous fiberreinforced ceramic composites. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature

KS G 3305-2022 搪瓷家用器皿

Porcelain enameled household ware

T/ZZB 3002-2022 龙泉青瓷酒瓶

本文件规定了龙泉青瓷中酒瓶的术语和定义、分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、 贮存和质量承诺。 本文件适用于以瓷土、釉土、紫金土为主要原料，采用低温氧化素烧、高温还原釉烧而成的青瓷酒瓶产品。

Longquan celadon bottle for wine

T/ZZB 2813-2022 日用硬质细瓷瓷器

本文件规定了日用硬质细瓷的产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存以及质量承诺。 本文件适用于以高岭土为主要原料，在1 300摄氏度以上高温烧成的日用硬质细瓷器类产品。

Domestic fine porcelain ware

T/SA 56.1-2022 冲泡与品鉴用陶瓷茶具 第1部分：乌龙茶茶具

第一章 范围 第二章 规范性引用文件 第三章 术语和定义 第四章 主要组成 第五章 结构设计 第六章 技术要求 第七章 试验方法 第八章 检验规则 第九章 标志、包装、运输和贮存

Ceramic tea set for brewing and tasting——Part 1:Oolong tea set

T/WCGH 002-2022 武夷岩茶冲泡品鉴茶具

本文件规定了武夷岩茶冲泡品鉴茶具的术语和定义、产品分类、技术要求、测定方法、检验规则和标志、包装、运输、贮存等。 适用于武夷岩茶冲泡品鉴的专用白色上釉瓷质器具。

Wuyi rock tea brewing and tasting tea set

T/JDZCA 0001-2022 “景德镇制”陶瓷技术要求 日用硬质瓷器

本文件规定了日用硬质瓷的术语和定义、分类、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本文件适用于以日用硬质瓷工艺制作而成的碗、盘、碟、盏、杯、壶等饮食器具。

"Made in Jingdezhen" ceramic technology requires daily hard porcelain

JC/T 2656-2022 碳化硅陶瓷制品 工业计算机层析成像（CT）检测

本文件规定了碳化硅陶瓷制品工业计算机层析成像（CT）检测的原理、试验条件、仪器设备、样品、试验步骤、试验数据处理、试验报告。 本文件适用于碳化硅陶瓷制品内部缺陷的工业CT检测，其他陶瓷材料制品内部缺陷的工业CT检测可参照使用。

Industrial computed tomography (CT) inspection of silicon carbide ceramic products

DB3602/T 0001-2022 “景德镇制”陶瓷品牌评价通用要求

"Jingdezhen Made" Ceramic Brand Evaluation General Requirements

DB4451/T 2-2022 地理标志产品 潮州手拉朱泥壶

Geographical indication product Chaozhou hand-drawn red clay pot

T/CCIA 0013-2022 日用陶瓷燃气隧道窑能效评价

Energy Efficiency Evaluation of Gas-fired Tunnel Kiln for Daily Ceramics

T/CZGX 001-2022 智能坐便器

本标准规定了智能坐便器的术语和定义、产品分类、技术要求、试验方法、检验规则、标志和标识、安装使用说明书、包装、运输和贮存。 1、技术要求主要有以下项目： ①　陶瓷便器部分项目 外观质量、变形、尺寸、厚度、智能坐便器排污口尺寸、水封、存水弯最小通径、耐荷重性、冲洗功能等项目。 ②　电子盖板部分项目 材料性能、整机防水等级、清洗功能、喷头自洁性能、暖风烘干性能、坐圈加热功能、耐水压性能、防水击性能、防虹吸性能、机械强度、耐久性、电源、电气安全、自动关闭、单位周期能耗、额定功率等项目。 本标准对冲洗平均用水量、清洗平均用水量、冲洗功能、单位周期能耗等技术要求进行了等级划分，对比国标的3级划分，此标准的划分的更为苛刻，对企业的产品有更高的技术要求。例如：将冲洗平均用水量不超过5.6L作为判定依据。 表1 冲洗平均用水量等级指标 项目 　领先 　优等 　合格  智能坐便器冲洗平均用水量　≤4.0　≤5.0　≤5.6 双冲智能坐便器全冲用水量最大限定值　≤5.0　≤6.0　≤7.0 注：每个水效等级中双冲智能坐便器的半冲平均用水量不大于其全冲用水量最大限定值的70％。 2、本标准对冲洗功能中球排放功能、颗粒排放功能、混合介质排放功能等项目进行优化提高相应的技术指标。 表2 排放功能 项目 　领先 　优等 　合格  球排放　排出100个　排出≥95个　排出≥90个 颗粒排放　残留颗粒0个 残留尼龙球0个　残留颗粒≤60 残留尼龙球≤3　残留颗粒≤125 残留尼龙球≤5 混合介质排放　第一次冲出数为28个　第一次冲出数≥25个，第二次全部冲出　第一次冲出数≥22个，第二次全部冲出 3、本标准对清洗功能中喷头伸出和收回时间、清洗平均用水量、清洗力项目进行优化提高相应的技术指标。 ①　喷头伸出和收回时间提高为喷嘴伸出时间不应大于8s；喷嘴回收时间不应大于8s。 ②　清洗平均用水量划分为3个等级。 表3 清洗平均用水量等级指标 项目 　领先 　优等 　合格  智能坐便器清洗平均用水量 ／L　≤0.30　≤0.50　≤0.70 ③　臀部清洗受力最大值应达到0.09N以上。 4、本标准对水温特性项目进行优化提高了相关技术指标。 清洗用水最高档的温度应控制在35℃～42℃； 即热式智能坐便器：在30s内偏差±2℃； 储热式智能坐便器：在30s内水温下降幅度不应大于3℃。 5、本标准对单位周期能耗项目进行优化提高了技术指标。 表4 单位周期能耗等级指标 项目 　领先 　优等 　合格  单位周期能耗 （KW·h）　带座圈加热　≤0.03　≤0.04　≤0.05 　不带座圈加热　≤0.01　≤0.02　≤0.03 这些检验项目中以冲洗平均用水量、冲洗功能、清洗平均用水量、清洗功能、喷头自洁性能、单位周期能耗为核心项目。

Smart water closets

KS L 5406-2022 压缩纤维接头

Compressed fiber jointing

QB/T 2455-2022 陶瓷颜料

ceramic pigments