83.100 泡沫材料 标准查询与下载

T/CPPIA 21-2022 地暖用挤塑聚苯乙烯泡沫（XPS）板

5.1　规格尺寸 产品主要规格尺寸见表1，其他规格由供需双方商定。 5.2　尺寸允许偏差 应符合表2的规定。 5.3　外观质量 5.3.1　SDXPS应表面平整，无夹杂物，颜色均匀。不应有影响使用的可见缺陷，如起泡、裂口、变形等。 5.3.2　GDXPS产品表面除槽口外，应表面平整，槽口均匀；均热层表面平整，无破损。 5.4　物理力学性能 应符合表3的规定。 5.5　绝热性能 应符合表4的规定。 5.6　燃烧性能 应不低于GB 8624 B2级。 5.7　总挥发性有机化合物释放限量 总挥发性有机化合物释放量应不大于0.45mg/m3。

Extruded polystyrene foam(XPS) board for floor heating

ASTM C578-22 硬质多孔聚苯乙烯隔热材料标准规范

1.1 This specification2 covers the types, physical properties, and dimensions of cellular polystyrene boards with or without facings or coatings made by molding (EPS) or extrusion (XPS) of expandable polystyrene. Products manufactured to this specification are intended for use as thermal insulation for temperatures from –65 to +165°F (–53.9 to +73.9°C). This specification does not apply to laminated products manufactured with any type of rigid board facer including fiberboard, perlite board, gypsum board, or oriented strand board. 1.1.1 Additional requirements for Types IV and XIII for pipe, tank, and equipment thermal insulation for temperatures from –320 to +165°F (–196 to +73.9°C) are contained in Annex A1. 1.2 The use of thermal insulation materials covered by this specification is potentially regulated by codes that address fire performance. For some end uses, specifiers need to also address the effect of moisture and wind pressure resistance. Guidelines regarding these end use considerations are included in Appendix X1. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation

ASTM D5672/D5672M-22 测试软质多孔材料的标准试验方法使用25毫米[1英寸]挠度技术测量压痕力挠度

1.1 This test method covers a screening type quality control test used to determine if flexible polyurethane foam cushions are within the specified grade range for firmness. 1.2 This test method is limited to foams with thicknesses that are 75 mm [3 in.] or greater. 1.3 This test method is based on the fact that the traditional industry standard thickness for Indentation Force Deflection (IFD) is 100 mm [4 in.], and the traditional percent deflection for IFD acceptance and product planning is 25 %. With respect, then, to these traditional industry conventions, a 25 % deflection on a 100-mm [4-in.] cushion would be 25 mm [1 in.]. Thus, deflecting standard cushions (of proper 100 mm thickness) 25 mm [1 in.] provides a quick way to determine if the flexible polyurethane foam is within the specified grade range for 25 % IFD. 1.4 Cushion thicknesses less than 75 mm [3 in.] shall not be tested for IFD using this test method. 1.5 This test method is intended to provide a quick and simple method to screen flexible polyurethane foams for determination of its firmness grade. 1.6 Units—The values stated in U.S. Customary or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—This test method and ISO 2439 address the same subject matter, but differ in technical content. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Testing Flexible Cellular Materials Measurement of Indentation Force Deflection Using a 25-mm [1-in.] Deflection Technique

ASTM C1303/C1303M-22 预测闭孔泡沫绝缘长期热阻的标准试验方法

1.1 This test method covers a procedure for predicting the long-term thermal resistance (LTTR) of unfaced or permeably faced rigid gas-filled closed-cell foam insulations by reducing the specimen thickness to accelerate aging under controlled laboratory conditions (1-5).2 NOTE 1—See Terminology, 3.2.1, for the meaning of the word aging within this standard. 1.2 Rigid gas-filled closed-cell foam insulation includes all cellular plastic insulations manufactured with the intent to retain a blowing agent other than air. 1.3 This test method is limited to unfaced or permeably faced, homogeneous materials. This method is applied to a wide range of rigid closed-cell foam insulation types, including but not limited to: extruded polystyrene, polyurethane, polyisocyanurate, and phenolic. This test method does not apply to impermeably faced rigid closed-cell foams or to rigid closed-cell bun stock foams. NOTE 2—See Note 8 for more details regarding the applicability of this test method to rigid closed-cell bun stock foams. 1.4 This test method utilizes referenced standard test procedures for measuring thermal resistance. Periodic measurements are performed on specimens to observe the effects of aging. Specimens of reduced thickness (that is, thin slices) are used to shorten the time required for these observations. The results of these measurements are used to predict the long-term thermal resistance of the material. 1.5 The test method is given in two parts. The Prescriptive Method in Part A provides long-term thermal resistance values on a consistent basis that can be used for a variety of purposes, including product evaluation, specifications, or product comparisons. The Research Method in part B provides a general relationship between thermal conductivity, age, and product thickness. 1.5.1 To use the Prescriptive Method, the date of manufacture must be known, which usually involves the cooperation of the manufacturer. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 Table of Contents: Section Scope 1 Reference Documents 2 Terminology 3 Summary of Test Method 4 Significance and Use 5 Part A: The Prescriptive Method 6 Applicability 6.1 Qualification Requirements 6.1.1 Facing Permeability 6.1.2 Apparatus 6.2 Sampling 6.3 Schedule 6.3.1 Specimen Preparation 6.4 Goal 6.4.1 Schedule 6.4.2 Replicate Test Specimen Sets 6.4.3 Specimen Extraction 6.4.4 Slice Flatness 6.4.5 Slice Thickness 6.4.6 Stack Composition 6.4.7 Storage Conditioning 6.5 Test Procedure 6.6 Thermal Resistance Measurement Schedule 6.6.1 Thermal Resistance Measurements 6.6.2 Product Density 6.6.3 Calculations 6.7 Part B: The Research Method 7 Background 7.1 TDSL Apparatus 7.2 Sampling Schedule 7.3 Specimen Preparation 7.4 Storage Conditioning 7.5 Test Procedure 7.6 Calculations 7.7 1 This test method is under the jurisdiction of ASTM Committee C16 on Thermal Insulation and is the direct responsibility of Subcommittee C16.30 on Thermal Measurement. Current edition approved June 1, 2022. Published July 2022. Originally approved in 1995. Last previous edition approved in 2019 as C1303/C1303M – 19. DOI: 10.1520/C1303_C1303M-22. 2 The boldface numbers in parentheses refer to the list of references at the end of this standard. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 Reporting 8 Reporting for Part A, the Prescriptive Method 8.1 Reporting for Part B, the Research Method 8.2 Precision and Bias 9 Keywords 10 Mandatory Information – Qualification Annex A1 Specimen Preparation A1.1 Homogeneity Qualification A1.2 Thermal Conductivity Equivalence Test Procedure A1.3 Alternate Product Thickness Qualification A1.4 Example Calculations A1.5 Mandatory Information-Preparation of Test Specimens for Spray-Foam Products Annex A2 Effect Of TDSL Appendix X1 History of the Standard Appendix X2 Theory of Foam Aging Appendix X3 References 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Predicting Long-Term Thermal Resistance of Closed-Cell Foam Insulation

KS M ISO 845-2022 泡沫塑料和橡胶 表观密度的测定

Cellular plastics and rubbers－Determination of apparent density

KS M ISO 3385-2022 柔性多孔聚合材料 恒载荷冲击疲劳测定

Flexible cellular polymeric materials－Determination of fatigue by constant-load pounding

KS M ISO 2439-2022 柔性多孔聚合物材料硬度测定（压痕技术）

Flexible cellular polymeric materials－ Determination of hardness(indentation technique)

KS M ISO 1798-2022 柔性多孔聚合物材料拉伸强度和断裂伸长率的测定

Flexible cellular polymeric materials－Determination of tensile strength and elongation at break

KS M ISO 20392-2022 绝热材料 压缩蠕变的测定

Thermal-insulating materials－Determination of compressive creep

KS M ISO 1209-1-2022 硬质泡沫塑料 弯曲性能的测定 第1部分：基本弯曲试验

Rigid cellular plastics－Determination of flexural properties－Part 1：Basic bending test

KS M ISO 20393-2022 绝热材料 扩散法长期吸水率的测定

Thermal-insulating materials－Determination of long-term water absorption by diffusion

KS M ISO 20394-2022 绝热材料 耐冻融性能测定

Thermal-insulating materials－Determination of freeze-thaw resistance

KS M ISO 1209-2-2022 硬质泡沫塑料 弯曲性能的测定 第2部分：弯曲强度和表观弯曲弹性模量的测定

Rigid cellular plastics－Determination of flexural properties－Part 2：Determination of flexural strength and apparent flexural modulus of elasticity

ASTM D1667-22 柔性多孔材料聚氯乙烯泡沫（闭孔）的标准规范

1.1 This specification covers flexible closed-cell or noninterconnecting cellular products, the elastomer content of which is predominantly poly(vinyl chloride) or copolymers thereof. 1.2 In the case of conflict between the provisions of this specification and those of detailed specifications or methods of test for a particular product, the latter shall take precedence. 1.3 Reference to the methods for testing closed-cell poly(vinyl chloride) contained herein shall specifically state the particular test or tests desired and not refer to these methods of test as a whole. 1.4 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.5 The following precautionary statement pertains to the test method portions only of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Flexible Cellular Materials—Poly (Vinyl Chloride) Foam (Closed-Cell)

T/ZZB 2710-2022 聚乳酸挤出发泡片材

本文件规定了聚乳酸挤出发泡片材（以下简称聚乳酸片材）的产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输与贮存和质量承诺。 本文件适用于以聚乳酸树脂为主要原料，添加物理发泡剂和其他助剂，经加热挤出成型制得的用于一次性包装用品的发泡片材。

Poly（lactic acid） extruded foam sheet

ASTM D3768-22 微孔聚氨酯弯曲恢复的标准试验方法

1.1 This test method covers the procedure and apparatus for measuring the flexural recovery of microcellular urethanes. 1.2 The values stated in SI units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Microcellular Urethanes—Flexural Recovery

KS M 6748-2021 医用橡胶板

Rubber sheets for medical purposes

KS M 3871-1-2021 硬质泡沫塑料 中密度喷涂聚氨酯泡沫 第1部分：规范

Rigid cellular plastics－Spray polyurethane foam medium density－Part 1：Specification

PN-EN ISO 844-2021-09 E 硬质泡沫塑料压缩性能的测定（ISO 844:2021）

Rigid cellular plastics--Determination of compression properties (ISO 844:2021)

BS ISO 23641:2021 柔性多孔聚合物材料 抗菌效果的测定

Flexible cellular polymeric materials. Determination of antibacterial effectiveness