83.160.01 标准查询与下载
共找到 338 条与 相关的标准，共 23 页
This International Standard specifies the interchangeability dimensions of ISO core chambers Nos. 1, 2 and 3 for tyre valves. For the applicability of the core chambers, see ISO 9413.
Tyre valves -- ISO core chambers No. 1, No. 2 and No. 3
- ICS
- 83.160.01
- CCS
- 发布
- 2013-09-09
- 实施
This Technical Report contains assigned kPa values for whole psi values in the range of 1 psi to 152 psi, for inflation pressures for use in certain regions of the world that require the use of psi for inflation pressures. These equivalencies are intended for future applications and do not apply to past practices.
Tyres, valves and tubes -- kPa/psi equivalencies for inflation pressures
- ICS
- 83.160.01
- CCS
- 发布
- 2013-09-09
- 实施
本标准规定了汽车轮胎定型胶囊平板式硫化模具的术语和定义、分类、型号编制方法、要求、检验方法、检验及判定规则、标志、包装、运输和贮存的要求。 本标准适用于轿车、轻型载重汽车、载重汽车、农业机械、工业车辆、工程机械等轮胎定型胶囊平板式硫化模具（以下简称模具）。
Automobile tire shaping bladder flat vulcanization mold
- ICS
- 83.160.01
- CCS
- G 95
- 发布
- 2013-07-15
- 实施
- 2013-10-15
本标准规定了轮胎翻新的术语和定义以及轮胎翻新生产技术规范。本标准适用于轿车、载重汽车、工程机械轮胎翻新。
Technical specification for retreaded tyre production
- ICS
- 83.160.01
- CCS
- G41
- 发布
- 2012-12-28
- 实施
- 2013-06-01
Tyre valves - Dimensions and designation; Amendment 1
- ICS
- 83.160.01
- CCS
- G41
- 发布
- 2012-10
- 实施
Further clarification of ISO 28580
- ICS
- 83.160.01
- CCS
- G41
- 发布
- 2012-07
- 实施
This SAE Recommended Practice describes a trio of test methods which determine basic tire size (geometry), mass, and moments of inertia. The methods apply to any tire so long as the equipment is properly scaled to conduct the measurements for the intended test tire. The data are suitable for determining parameters for road load models and for comparative evaluations of the measured properties in research and development. NOTE-Herein, road load models are models for predicting forces applied to the vehicle spindles during operation over irregular surfaces paved or unpaved. Within the context of this Recommended Practice, forces applied to the surface on which the tire is operating are not considered.
Tests to Define Tire Size (Geometry), Mass, and Inertias
- ICS
- 83.160.01
- CCS
- G41
- 发布
- 2012-06-21
- 实施
- 2018-05-29
Tyre valves - Dimensions and designation.
- ICS
- 83.160.01
- CCS
- T22
- 发布
- 2012-06-01
- 实施
- 2012-06-02
本标准规定了农业轮胎耐磨耗性能的试验条件、试验仪器设备及其精度要求、试验步骤、试验记录。 本标准适用于测定农业驱动轮胎的耐磨耗性能。
Test method of wear performance for agricultural tyres.Double drum method
- ICS
- 83.160.01
- CCS
- G41
- 发布
- 2012-05-24
- 实施
- 2012-11-01
本规范规定了轮胎静负荷性能的术语和定义、试验设备、试验条件、试验步骤、试验记录和数值计算、试验报告。 本标准适用于轿车轮胎、载重汽车轮胎、工程机械轮胎、工业车辆轮胎、农业轮胎以及摩托车轮胎。
Test method of static loaded performance for tyres
- ICS
- 83.160.01
- CCS
- G41
- 发布
- 2012-05-24
- 实施
- 2012-11-01
警告——使用本标准的人员应有正规实验室工作的实践经验，本标准并未指出所有可能的安全问题，使用者有责任采用适当的安全和健康措施，并保证符合国家有关法规规定的条件。 本标准规定了轮胎水压试验的术语和定义、原理、实验装置、试验方法、计算公式、试验报告。 本标准适用于轿车轮胎、载重汽车轮胎、农业轮胎、工程机械轮胎、工业车辆轮胎的水压试验。
Test method of water pressure for tyres
- ICS
- 83.160.01
- CCS
- G41
- 发布
- 2012-05-24
- 实施
- 2012-11-01
Tyre valves. Dimensions and designation
- ICS
- 83.160.01
- CCS
- G41
- 发布
- 2012-04-30
- 实施
- 2012-04-30
Specification for the manufacture and storage of size reduced tyre materials. (Purchase from www.wrap.org.ukonly)
- ICS
- 83.160.01
- CCS
- G41
- 发布
- 2012-02-02
- 实施
- 2012-02-02
Tyre valves - Dimensions and designation
- ICS
- 83.160.01
- CCS
- G41
- 发布
- 2012-02-01
- 实施
1.1 This test method covers laboratory measurement of the hydraulic conductivity (also referred to as coefficient of permeability) of water-saturated tired derived aggregates (TDA) obtained from scrap tires using a rigid-wall pe......
Standard Test Method for Measurement of Hydraulic Conductivity of Tire Derived Aggregates Using a Rigid Wall Permeameter
- ICS
- 83.160.01
- CCS
- 发布
- 2012
- 实施
本标准规定了轮胎气门嘴延伸管（以下简称延伸管）试验的术语和定义、试验设备、仪器仪表、密封性试验、连接试验和爆破试验。 本标准适用于载重汽车（包括客车、挂车及无轨电车）、工业车辆、工程机械、拖拉机、农业和林业机械等轮胎气门嘴充气用延伸管的试验。
Test method for tyre valve extension
- ICS
- 83.160.01
- CCS
- G41
- 发布
- 2011-12-20
- 实施
- 2012-07-01
本标准规定了轮胎气门嘴延伸管（以下简称延伸管）的术语和定义、型号标记、结构型式及尺寸、零部件的类型、结构尺寸及材料、外观、密封性、连接、爆破、试验方法、检验规则、标识、包装和贮存。 本标准适用于载重汽车（包括客车、挂车及无轨电车）、工业车辆、工程机械、拖拉机、农业和林业机械等轮胎气门嘴充气用延伸管。
Tyre valves extension
- ICS
- 83.160.01
- CCS
- G41
- 发布
- 2011-12-20
- 实施
- 2012-07-01
本标准规定了轮胎外观质量要求。 本标准适用于载重汽车、轿车、工程机械、工业车辆、农业、摩托车等充气轮胎和充气轮胎轮辋实心轮胎、压配式实心轮胎的外胎及其使用的垫带。
Appearance quality of tyres
- ICS
- 83.160.01
- CCS
- G41
- 发布
- 2011-12-20
- 实施
- 2012-07-01
이 표준은 주로 승용차, 트럭 그리고 버스에 사용하기 위해 설계된 신규 공기 타이어에 대해
Passenger car, truck and bus tyres-Methods of measuring rolling resistance-Single point test and correlation of measurement results
- ICS
- 83.160.01
- CCS
- G41
- 发布
- 2011-10-04
- 实施
- 2011-10-04
