87.060.30 溶剂 标准查询与下载

CNS 3698-2005 水溶性切削冷却液

本标准适用于金属切削刀具冷?及润滑用之水溶性油剂

Water soluble cutting fluid

CNS 13380-2005 己烷

本标准适用于作为植物性油脂、鱼油、树脂等之萃取溶剂；制造聚烯烃弹性体及药物等反应媒介物；制造胶带、黏着剂、清漆及轮胎等溶剂之己烷。

Hexanes

CNS 14915-2005 庚烷（工业用）

本标准适用于作为洋干漆黏着剂之稀释剂、扩散剂及有机合成工业用溶剂之庚烷。

Industrial heptanes

ASTM D608-05(2011) 邻苯二甲酸二丁酯的标准规格

1.1 This specification covers dibutyl phthalate (99 % grade). 1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.

Standard Specification for Dibutyl Phthalate

ASTM D2694-05(2011) 二甘醇标准规范

1.1 This specification covers diethylene glycol for use in the preparation of surface coatings. 1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 For specific hazard information and guidance, consult the supplier''s Material Safety Data Sheet. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Diethylene Glycol

ASTM D3734-05(2010) 高闪点芳烃石脑油的标准规范

1.1 This specification covers two types of aromatic hydrocarbon solvents, normally petroleum distillates, having high flash points, moderately low volatility, and a distillation range of approximately 30°C (50°F). These solvents are used primarily by the coatings industry and are commonly referred to as high-flash aromatic naphthas. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.4 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.

Standard Specification for High-Flash Aromatic Naphthas

ASTM D509-05(2011)e1 松香分级和抽样的标准试验方法

Rosin is an important product of the centuries old Naval Stores industry and is produced and consumed in many countries throughout the world. Consequently, reliable methods of sampling and grading rosin are necessary. The test methods based on the use of the USDA Official Standards described herein, were developed many years ago for the sampling and grading of rosin and are similar to those included in the Naval Stores Act. Although these test methods based on the use of the USDA Official Standards are still applicable, many additional test methods are now used to grade rosin. In particular, the color of rosin is now more commonly reported using the Gardner color scale rather than the USDA Official Standards. In addition, Test Methods E28, D465, and D5974 are widely used to assess the quality of rosin in addition to the color grading methods described in this standard.1.1 These test methods cover procedures for sampling and determining the grade of rosin delivered in commercial bags, barrels, drums or in molten form. Although developed for rosin, these methods can also be used for the grading of modified rosins and rosin based resins. Note 18212;All rosin sold in interstate commerce must be described by reference to the U. S. Standards for rosin, and is therefore subject to grading prior to such sale. The grading procedure described in these test methods is used for checking grades or regrading after the rosin has moved from the primary markets to distributing or consuming points. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods of Sampling and Grading Rosin

ASTM D6438-05(2010) 液相微萃取 - 气相色谱法测量在涂料涂层中丙酮,甲基丙酮和三氯甲苯含量标准试验方法

In order to calculate the volatile organic content (VOC) of paints containing EPA exempt solvents, it is necessary to know the acetone, methyl acetate, or parachlorobenzotrifluoride content. This gas chromatographic test method provides a simple and direct way for measuring these solvents. Each analyte is measured with respect to a unique internal standard. For acetone, the internal standard used is acetone-d6, for methyl acetate it is methyl acetate-d3, and for PCBTF it is metachlorobenzotrifluoride (MCBTF). These unique analyte/internal standard pairs behave very nearly as single solvents with respect to evaporation rate and adsorption rate onto a coated silica fiber (SPME) but are separable on a gas chromatograph (GC) capillary column. The only critical analytical technique required for successfully performing this test method is the ability of an analyst to weigh a paint sample and internal standard, corresponding to the analyte of interest, into a septum capped vial. After weighing, solvent evaporation has no effect on the final value of the determination. Since whole paint is not injected into the gas chromatograph, the analytical system is never compromised.1.1 This test method is for the determination of acetone, methyl acetate, or parachlorobenzotrifluoride (PCBTF), or combination of any of the three, in paints and coatings, by solid phase microextraction (SPME) headspace sampling, and subsequent injection into a gas chromatograph. It has been evaluated for cellulose nitrate, acrylic, and urethane solvent-borne systems. The established working range of this test method is: acetone, 28 to 90 %; methyl acetate, 12 to 22 %; parachlorobenzotrifluoride, 10 to 17 %. There is no reason to believe that it will not work outside these ranges. A minor modification of this test method would make it suitable for the analysis of the same analytes in water-borne coatings (see Note 1). Note 18212;Water-borne paints are internally standardized and diluted with water followed by addition of solid sodium chloride. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Acetone, Methyl Acetate, and Parachlorobenzotrifluoride Content of Paints, and Coatings by Solid Phase Microextraction-Gas Chromatography

ASTM D1612-05 甲醇中丙酮含量的标准试验方法

This test method can be used to detect residual amounts of carbonyl compounds in synthetic and natural methanol. The carbonyl compounds are quantified by comparison to a known standard of acetone solution. Carbonyl compounds may be present as a result of contamination during storage, distribution, or manufacture. This test method may be used in assessing compliance with a specification.1.1 This test method covers a procedure for detecting the presence of acetone in methanol in amounts greater than 0.003 weight %. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.5 For hazard information and guidance, see the supplier''s Material Safety Data Sheet.

Standard Test Method for Acetone in Methanol

ASTM D3362-05 气相色谱法测定丙烯酸酯纯度的标准试验方法

This test method provides a measurement of commonly found impurities in commercially available methyl acrylate, ethyl acrylate, butyl acrylate, and 2-ethylhexyl acrylate. The measurement of these impurities and the results thereof can either individually or when totaled and subtracted from 100 (assay) be used for specification purposes.1.1 This test method covers the determination of the purity of acrylate, ethyl acrylate, n-butyl acrylate, and 2-ethylhexyl acrylate by gas chromatography and, in addition, provides a means for measuring certain impurities such as alcohols and other esters. Water and acidity are measured by other appropriate ASTM procedures and the results are used to normalize the chromatographic values.1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 For hazard information and guidance, see the supplier''s Material Safety Data Sheet.1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.

Standard Test Method for Purity of Acrylate Esters by Gas Chromatography

ASTM D3541-05 2-乙基己基丙烯酸酯的标准规范

1.1 This specification covers 2-ethylhexyl acrylate (99 % grade) for use in paint, varnish, lacquer, and related products.1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded-off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Specific hazard statements are given in 4.1.1.3 For specific hazard information and guidance, consult supplier''s Material Safety Data Sheet.

Standard Specification for 2-Ethylhexyl Acrylate

ASTM D3620-04 冰醋酸标准规范

1.1 This specification covers glacial (99.8 %) acetic acid for use in paint, varnish, lacquer, and related products.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.5 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.

Standard Specification for Glacial Acetic Acid

CNS 14797-2004 矿物型溶剂

本标准适用于干洗及涂料等工业之溶剂（烃类）用途

Mineral spirits（hydrocarbon dry cleaning solvent,petroleum spirits,stoddard solvent）

ASTM D3698-04(2010) 溶剂蒸气脱脂操作方法的标准实施规程

This practice is intended for use by employers in developing their own specific operation standards for solvent vapor degreasing operations. Certain vapor degreasing operations are subject to the requirements of the National Emission Standards for Halogenated Solvent Cleaning (Halogenated Solvent Cleaner NESHAP) as found in 40 CFR Part 63, Subpart T. The determination of the applicability of these, or any additional requirements is the responsibility of the user. This practice is not intended to address all of the requirements contained in the Halogenated Solvent Cleaner NESHAP. Development and implementation of training programs, recordkeeping, and other additional requirements of the NESHAP are the responsibility of the user.1.1 This practice recommends work practices for conventional vapor degreasing operations utilizing any solvent or solvent blend that has been categorized as nonflammable. 1.2 This practice is not intended for use in vapor degreasing operations utilizing flammable (low flash point) solvents or in vapor degreasing operations utilizing enclosed (sealed, airtight) equipment. For these non-applicable operations, users should consult the solvent or equipment supplier for additional information. 1.3 The values given in inch-pound units are to be regarded as the standard. The values stated in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Solvent Vapor Degreasing Operations

NAVY A-A-59743-2003 清洁复合溶剂 DICHLOROPENTAFLUOROPROPANE(氟氯烃 225 )

This commercial item description (CID) covers a dichloropentafluoropropane (HCFC-225) cleaning compound solvent for precision cleaning applications.

CLEANING COMPOUND SOLVENT, DICHLOROPENTAFLUOROPROPANE (HCFC-225)

DIN 55652:2003 涂料和清漆溶剂.痕量酸度测定

The standard describes a test method for determining the acidity, expressed as the acid content (as a mass fraction of acetic acid in percent)or as the acid value, of solvents and material mixtures. The methods are applicable to alcohols, ketones, ethers, esters, aliphatic and aromatic hydrocarbons and mixtures prepared from these chemicals having an lower acid content up to 0,1%, resp. an acid value less than 0,001 mg KOH/g.#,,#

Solvents for paints and varnishes - Determination of acidity of traces

ASTM D2349-90(2003) 用于定性测定溶剂可降解涂料中溶剂组成的性质的标准测试方法

Standard Test Method for Qualitative Determination of Nature of Solvent Composition in Solvent-Reducible Paints

ASTM D1720-03(2008) 硝酸纤维素溶液中活性溶剂稀释比的标准试验方法

By use of standard or reference grade materials for any two of the three components, namely, oxygenated solvent, diluent, or cellulose nitrate, the effect of different batches or different types of the third component can be determined. This test method is applicable for the determination of the following: The dilution ratio of toluene as the standard diluent to an oxygenated solvent under test, using as the solute standard cellulose nitrate as defined in 5.2. The dilution ratio of a hydrocarbon diluent under test to n-butyl acetate as the standard solvent, using as a solute standard cellulose nitrate as defined in 5.2. The dilution ratio of toluene, as the standard diluent, to n-butyl acetate as the standard solvent, using as the solute cellulose nitrate of varying solubility characteristics. The information developed through this test may be useful in the formulation of cellulose-based lacquers and adhesives.1.1 This test method covers the determination of the volume ratio of hydrocarbon diluent to active solvent required to cause persistent heterogeneity (precipitation) in a solution of cellulose nitrate. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6. 1.5 For hazard information and guidance, see the supplier's Material Safety Data Sheet.

Standard Test Method for Dilution Ratio of Active Solvents in Cellulose Nitrate Solutions

KS M ISO 4626-2002(2017) 挥发性有机液体原料有机溶剂沸点范围的测定

Volatile organic liquid－Determination of boiling range of organic solvents used as raw material

KS M ISO 4626:2002 挥发性有机液体.用作原料的有机溶剂沸程的测定

1.1 이 규격은 일반 압력에서 30∼300°C 사이에 끓으며, 화학적으로 안정하고,

Volatile organic liquid－Determination of boiling range of organic solvents used as raw material