F19 新能源及其他 标准查询与下载

IEC TS 62282-7-2:2014 燃料电池技术.第7-2部分:.试验方法.固体氧化物燃料电池(SOFC)用单电池和栈性能试验方法

Fuel cell technologies - Part 7-2: Test methods - Single cell and stack performance test methods for solid oxide fuel cells (SOFC)

ISO 14687-3:2014 氢燃料.产品规格.第3部分:固定电器用质子交换膜(PEM)燃料电池的应用

This partofISO 14687 specifiesthe quality characteristics ofhydrogen fuel in orderto ensure uniformity of the hydrogen product for utilization in stationary proton exchange membrane (PEM)] fuel cell power Systems，

Hydrogen fuel - Product specification - Part 3: Proton exchange membrane (PEM) fuel cell applications for stationary appliances

CFR 18-2.55-2014 电力和水资源保护. 第2部分:总体的政策和解释. 第2.55节:第7(c)节中条款的解释.

For the purposes of section 7(c) of the Natural Gas Act, as amended, the word facilities as used therein shall be interpreted to exclude.

Conservation of power and water resources. Part2:General policy and interpretations. Section2.55:Definition of terms used in section 7(c).

IEC 105/443/DTS:2013 IEC/TS 62282-7-2 燃料电池技术 第7-2部分 固体氧化物燃料电池(SOFC)用单电池/栈性能试验方法

IEC/TS 62282-7-2: Fuel cell technologies - Part 7-2: Single cell/stack performance test methods for solid oxide fuel cells (SOFC)

IEC 82/728/DTS:2012 IEC/TS 62257-1, Ed. 2:农村电气化用小型可再生能量和混合能量系统推荐性规程.第1部分:农村电气化概述

IEC/TS 62257-1, Ed. 2: Recommendations for small renewable energy and hybrid systems for rural electrification - Part 1: General introduction to rural electrification

NB/T 34002-2011 农村风光互补室外照明装置

本标准规定了农村风光互补室外照明装置（以下简称风光照明装置）的风/光资源条件和外界条件、装置分类、装置性能要求、试验方法、安装要求、连接要求、试运行验收与交付检验、可靠性要求、质量判定与检验规则、装置标志与使用说明书、包装与运输要求等。 本标准适用于我国农村乡镇与村庄的道路、庭院、广场等公共场所照明用风光互补室外独立照明装置。

Wind-PV lighting device for rural area outdoor

JIS C 8841-1:2011 小型固体氧化物燃料电池动力系统.第1部分:总则

This Japanese Industrial Standard specifies the general rules, such as the composition, structure, method of connection to the outside of a package and inspection for stationary small solid oxide fuel cell power systems (hereafter referred to as "fuel cell systems") that are in accordance with the following a) to h).

Small solid oxide fuel cell power systems -- Part 1: General rules

JIS C 8841-2:2011 小型固体氧化物燃料电池动力系统.第2部分:一般安全规程和安全性测试方法

This Japanese Industrial Standard specifies the necessary matters for the safety standards,safety test methods and performance maintenance management of the stationary small solid oxide fuel cell power systems (hereafter referred to as "fuel cell systems"),such as matters related to the structure,material,function,installation criteria,marking,indicator, and operation manual. The fuel cell systems covered by this Standard shall be in accordance with the following a) to h).

Small solid oxide fuel cell power systems -- Part 2: General safety codes and safety testing methods

JIS C 8841-3:2011 小型固体氧化物燃料电池动力系统.第3部分:性能测试方法和环境测试方法

This Japanese Industrial Standard specifies the performance testing methods and environment testing methods of the stationary small solid oxide fuel cell power systems (hereafter referred to as "fuel cell systems") which are in accordance with the following a) to h).

Small solid oxide fuel cell power systems -- Part 3: Performance testing methods and environment testing methods

ASTM D4806-11a 用于汽车电火花点火发动机燃料的与汽油混合的变性燃料酒精的标准规范

1.1 This specification covers nominally anhydrous denatured fuel ethanol intended to be blended with unleaded or leaded gasolines at 1 to 10 volume % for use as automotive spark-ignition engine fuel covered by Specification D4814. The significance of this specification is shown in Appendix X1. 1.2 The user is advised to check with the national regulatory agencies where the ethanol is denatured and used. The sulfur limit and denaturing formulas in this specification are acceptable for the U.S. market. Other countries or jurisdictions may allow or require other denaturing formulas and sulfur limits. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 The following safety hazards caveat pertains only to the method modification in 8.7 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel

DB37/T 1686-2010 轧钢加热炉节能运行技术要求

Technical requirements for energy-saving operation of steel rolling heating furnace

DB37/T 1687-2010 干熄焦节能运行技术要求

CDQ energy-saving operation technical requirements

BS EN 62282-6-100:2010 燃料电池技术.微型燃料电池动力系统.安全性

a) This consumer safety standard covers micro fuel cell power systems, micro fuel cell power units and fuel cartridges that are wearable or easily carried by hand, providing d.c. outputs that do not exceed 60 V d.c. and power outputs that do not exceed 240 VA. Portable fuel cell power systems that provide output levels that exceed these electrical limits are covered by IEC 62282-5-1. b) Externally accessible circuitry is therefore considered to be safety extra low voltage (SELV) circuitry as defined in IEC 60950-1:2005, and as limited power circuits if further compliance with 2.5 of IEC 60950-1:2005 is demonstrated. Micro fuel cell power systems or units that have internal circuitry exceeding 60 V d.c. or 240 VA should be appropriately evaluated in accordance with the separate criteria of IEC 60950-1:2005. c) This consumer safety standard covers all micro fuel cell power systems, micro fuel cell power units and fuel cartridges. This standard establishes requirements for all micro fuel cell power systems, micro fuel cell power units and fuel cartridges to ensure a reasonable degree of safety for normal use, reasonably foreseeable misuse, and consumer transportation of such items. The fuel cartridges covered by this standard are not intended to be refilled by the consumer. Fuel cartridges refilled by the manufacturer or by trained technicians shall meet all requirements of this standard. d) These products are not intended for use in hazardous areas as defined by IEV 426-03-01.

Fuel cell technologies - Micro fuel cell power systems - Safety

ANSI/NFPA 853-2010 固定燃料电池动力设备的安装标准

1.1 Scope. 1.1.1 This standard shall apply to the design, construction, and installation of stationary fuel cell power systems. 1.1.2 The scope of this document shall include the following: (1) A singular prepackaged, self-contained power system unit (2) Any combination of prepackaged, self-contained power system units (3) Power system units comprising two or more factory-matched modular components intended to be assembled in the field (4) Engineered and field-constructed power systems that employ fuel cells

Standard for the Installation of Stationary Fuel Cell Power Systems

ASTM D5798-10a 机动车火花点火式发动机用燃料乙醇(ED70-ED85)的标准规范

1.1 This specification covers a fuel blend, nominally 70 to 85 volume % denatured fuel ethanol and 30 to 15 additional volume % hydrocarbons for use in ground vehicles with automotive spark-ignition engines. Appendix X1 discusses the significance of the properties specified. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Fuel Ethanol (Ed70-Ed85) for Automotive Spark-Ignition Engines

ASTM D4806-10b 与用作汽车电火花点火发动机燃料的汽油混合用的变性燃料酒精的标准规范

1.1 This specification covers nominally anhydrous denatured fuel ethanol intended to be blended with unleaded or leaded gasolines at 1 to 10 volume % for use as automotive spark-ignition engine fuel covered by Specification D4814. The significance of this specification is shown in Appendix X1. 1.2 The user is advised to check with the national regulatory agencies where the ethanol is denatured and used. The sulfur limit and denaturing formulas in this specification are acceptable for the U.S. market. Other countries or jurisdictions may allow or require other denaturing formulas and sulfur limits. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 The following safety hazards caveat applies to the test method in 8.7: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel

NY/T 1704-2009 沼气电站技术规范

本标准规定了沼气发电站的总体布置、基本建设内容、安全运行等要求。 本标准适用于装机容量10kW~10000kW的沼气发电站。

Biogas power generation technology criterion

NY/T 1699-2009 玻璃纤维增强塑料户用沼气池技术条件

本标准规定了以玻璃纤维增强塑料，以树脂为基体的玻璃钢户用沼气池产品（以下简称玻璃钢）的技术要求、试验方法、检验规则和标志、运输等内容。 本标准适用于接触成型（含手糊、喷射工艺）、片状模塑料（SMC）模压成型、树脂传递模塑（RTM）成型和缠绕成型工艺的玻璃钢材料户用沼气池和户用沼气池拱。

Technical specifications for household anaerobic digesters of fiberglass reinforced plastics

ARP 062-9-1-2009 乡村电气化的小型更新能源和混合系统推荐标准.第9-1部分:微动力系统

Applies to micropower plant for electric energy generation subsystem associated with a decentralized rural electrification system. Provides general requirements for the design, erection and operation of micropower plants and general requirements to ensu

Recommendations for small renewable energy and hybrid systems for rural electrification Part 9-1: Micropower systems

ARP 062-7-2008 乡村电气化的小型更新能源和混合系统推荐标准.第7部分:发电机

Specifies general requirements for generators with maximum power equal to 100 kVA in decentralized rural electrification systems. Identifies main items to be considered when selecting, sizing, installing, operating and maintaining the equipment.

Recommendations for small renewable energy and hybrid systems for rural electrification Part 7: Generators