G09 卫生、安全、劳动保护 标准查询与下载

ANSI/ASSE A10.3-2013 炸药驱动紧固系统的安全性要求

Safety Requirements for Powder-Actuated Fastening Systems

DB32/T 2171-2012 石油化工码头企业安全生产标准化规范

Standardized Specifications for Safety Production of Petrochemical Terminal Enterprises

DB11/ 833-2011 危险化学品地上储罐区安全要求

本标准规定了危险化学品地上储罐区的一般要求、安全要求和特殊要求。本标准适用于危险化学品生产经营单位的危险化学品地上储罐区建设和管理工作。本标准不适用于危险化学品仓库、危险化学品地下储罐、汽车加油加气站的储罐、医疗用气体储罐、科研用气体储罐建设和管理工作。

Safety Requirements for Aboveground Storage Tank Areas of Hazardous Chemicals

ANSI/NFPA 400-2012 危险品规程

1.1 Scope. 1.1.1* Applicability. This code shall apply to the storage, use, and handling of the following hazardous materials in all occupancies and facilities: (1) Ammonium nitrate solids and liquids (2) Corrosive solids and liquids (3) Flammable solids (4) Organic peroxide formulations (5) Oxidizer - solids and liquids (6) Pyrophoric solids and liquids (7) Toxic and highly toxic solids and liquids (8) Unstable (reactive) solids and liquids (9) Water-reactive solids and liquids (10)*Compressed gases and cryogenic fluids as included within the context of NFPA 55, Compressed Gases and Cryogenic Fluids Code 1.1.1.1 Occupancies. Unless otherwise specified in this code, all occupancy definitions and classifications shall be in accordance with the building code. 1.1.1.2 Multiple Hazards. Hazardous materials that are classified in more than one hazard category, as set forth in Section 4.1, shall conform to the code requirements for each hazard category. 1.1.2 Exemptions. 1.1.2.1 The quantity and arrangement limits in this code shall not apply to facilities that use ammonium perchlorate in the commercial manufacture of large-scale rocket motors. 1.1.2.2 This code shall not apply to the following: (1) Storage or use of hazardous materials for individual use on the premises of one- and two-family dwellings (2) Explosives or blasting agents, which are regulated by NFPA 495, Explosive Materials Code, and display fireworks, 1.3 G, which are regulated by NFPA1124, Code for the Manufacture, Transportation, Storage, and Retail Sales of Fireworks and Pyrotechnic Articles (3) Refrigerants and refrigerant oil contained within closed cycle refrigeration systems complying with the fire code and the mechanical code adopted by the jurisdiction (4) High hazard contents stored or used in farm buildings or similar occupancies and in remote locations for on premises agricultural use (5) Corrosive materials in stationary batteries utilized for facility emergency power or uninterrupted power supply, or similar purposes, in accordance with NFPA 1, Fire Code (6) Aerosols complying with NFPA 30B, Code for the Manufacture and Storage of Aerosol Products (7) Consumer fireworks, 1.4G complying with NFPA 1124, Code for the Manufacture, Transportation, Storage, and Retail Sales of Fireworks and Pyrotechnic Articles (8) Corrosive materials displayed in original packaging in mercantile occupancies and intended for personal or household use or as building materials (9) Flammable and combustible liquids having no other physical or health hazard properties covered by this code (10) Organic peroxide formulations that are capable of detonation either unpackaged or in their normal shipping containers under conditions of fire exposure, when in accordance with NFPA 495, Explosive Materials Code (11) Combustible metals, as defined in NFPA484, Standard for Combustible Metals (12) LP-Gas complying with NFPA 58, Liquefied Petroleum Gas Code or NFPA 59, Utility LP-Gas Plant Code (13) When approved, materials that have been satisfactorily demonstrated not to present a potential danger to public health, safety, or welfare, based upon the quantity or condition of storage.

Hazardous Materials Code

KS M ISO 3165:2011 工业用化学制品取样.取样的安全性

이 표준은 산업용 화학 제품 시료의 안전성과 관련된 것을 규정한다.

Sampling of chemical products for industrial use-Safety in sampling

DB13/T 1416.2-2011 作业场所职业职业危害检测规范 第2部分：淀粉、葡萄糖行业

本标准规定了淀粉、葡萄糖生产行业作业场所职业危害因素的术语和定义、总则、职业危害因素的识别及分类、采样前的准备、采样质控的要求、采样点的设置、个体采样及检验方法。本标准适用于淀粉、葡萄糖生产行业作业场所职业危害因素的检测、评价和相关规程的编制。

Occupational Occupational Hazard Testing Specifications in the Workplace Part 2: Starch and Glucose Industry

SN/T 2880-2011 固体化学品可燃性测定方法

本标准规定了固体化学品可燃性试验的仪器和测试步骤、判定方法。 本标准适用于对固体化学品可燃性的测定。

Method for Determination of Flammability of Solid Chemicals

SN/T 2903-2011 危险品 易燃液体黏度测定方法 毛细管法、旋转黏度计法、受力球黏度计法

本标准规定了危险品易燃液体的黏度的实验仪器和测试步骤、判定方法。 本标准适用于对危险品易燃液体的黏度（毛细管法、旋转黏度计法、受力球黏度计法）的测定。

Determination of viscosity of dangerous goods flammable liquid capillary method, rotational viscometer method, forced ball viscometer method

SN/T 2902-2011 危险品热稳定性和空气稳定性的筛选实验

本标准规定了危险品热稳定性和空气稳定性筛选实验的仪器和测试步骤。 本标准适用于对危险品热稳定性和空气稳定性试验的测定。

Screening experiments for thermal stability and air stability of dangerous goods

DB11/ 755-2010 危险化学品仓库建设及储存安全规范

本标准规定了危险化学品仓储设施建设和储存的一般要求，以及危险化学品生产、经营、使用单位危险化学品储存的安全要求。本标准适用于危险化学品生产、经营、使用单位总面积小于550㎡的危险化学品仓库的建设及储存。

Hazardous chemicals warehouse construction and storage safety regulations

DB37/T 1716-2010 煤化工企业安全预警信息系统技术要求

Technical Requirements for Safety Early Warning Information System of Coal Chemical Industry Enterprises

DB11/ 754-2010 石油储罐机械化清洗施工安全规范

Construction Safety Code for Mechanized Cleaning of Petroleum Storage Tanks

AQ 3038-2010 电石生产企业安全生产标准化实施指南

本标准规定了电石生产企业(以下简称企业)安全生产标准化管理的技术要求。 本标准适用于采用密闭炉、内燃式电石炉生产电石的企业。生产工艺主要以石灰、炭素材料为原料,采用电阻电弧炉生产工业电石的企业。

Guidelines for work safety standardization of calcium carbide enterprises

AQ 3040-2010 涂料生产企业安全生产标准化实施指南

本标准规定了属于危险化学品行业的涂料生产企业(以下简称企业)开展安全生产标准化的过程和要求。 本标准适用于中华人民共和国境内,原料、中间产品或产品属于危险化学品的涂料生产企业,其生产过程包括配料、分散、研磨、调漆、检验、包装、储运等,以及相关的树脂合成或油脂热炼等操作工艺和作业过程。

Guidelines for work safety standardization of coating enterprises

AQ 3039-2010 溶解乙炔生产企业安全生产标准化实施指南

本标准规定了溶解乙炔生产企业(以下简称企业)开展安全生产标准化的过程和技术要求。 本标准适用于采用碳化钙或天然气裂解生产粗乙炔气,经过净化、干燥、加压工序,生产溶解乙炔的企业。

Guidelines for work safety standardization of dissolved acetylene enterprise

AQ 3037-2010 硫酸生产企业安全生产标准化实施指南

本标准规定了硫酸生产企业(以下简称企业)开展安全生产标准化的过程和要求。 本标准适用于中华人民共和国境内采用以硫铁矿(砂)、硫磺、冶炼烟气、石膏、有色金属矿为原料,生产硫酸、二氧化硫等产品的企业,该生产工艺包括原料气的制取、净化、转化、干吸、余热利用等工艺单元。 采用其他原料生产硫酸、二氧化硫的企业可参照执行。

Guidelines for work safety standardization of sulphuric acid enterprises

ANSI Z400.1/Z129.1-2010 美国国家工作场所危险化学品–危害评估和安全数据表和预防标签准备标准

This Standard applies to the preparation of SDSs and precautionary labeling for hazardous chemicalsused under occupational conditions. It presents basic information on how to develop and write SDSs andprecautionary labels. It also identifies information that must be included to comply with the HCS.Additional information is provided to help comply with state and federal environmental and safety lawsand regulations. Elements of this Standard may also be acceptable for international use. This Standardis not intended to address the distribution of SDSs.This Standard is not intended to provide a rote specification for complying with the HCS or any othergovernment requirements. Safety data sheet and precautionary labeling requirements and definitions aresubject to change. It is the responsibility of the SDS and label preparer to be aware of current HCSrequirements.This Standard must be applied in a manner consistent with all statutory and regulatory requirements,including the United States Occupational Safety and Health Administration (OSHA) HazardCommunication Standard (HCS; 29 CFR 1910.1200) and the substance specific standards (29 CFR1910.1001-1052).There are use-specific statutory and regulatory requirements for some chemical products that are outsidethe scope of OSHA HCS and therefore may have different SDS and/or labeling requirements. Someexamples include:? consumer products regulated by the Federal Hazardous Substances Act (FHSA),? medical products regulated by the Federal Food, Drug and Cosmetic Act (FFDCA),? pesticides regulated by the Federal Insecticide, Fungicide and Rodenticide Act (FIFRA),? materials in transportation regulated by the Department of Transportation (DOT) HazardousMaterials Regulations, and? laboratory chemicals regulated under 29 CFR 1910.1450, the “OSHA Laboratory Standard”.See 29 CFR 1910.1200(b) for information on the scope and application of the HCS.For example, a company that manufactures aspirin tablets does not need to produce and distribute SDSsto individuals that are taking aspirin to treat pain or some other medical condition. This includes aspirintablets taken by a worker in the workplace. In this scenario, the aspirin would fall under the jurisdiction ofthe FDA, not OSHA. However, the company would be required to produce OSHA hazard communicationdocuments (such as an SDS and labels) for workers who may be exposed to aspirin powder during themanufacture of the tablets.It is not the intent of this Standard to substitute for specific regulatory requirements or to list each andevery unique requirement. Where there is a conflict between the applicable regulations and thisStandard, the regulations must take precedence over this Standard. References to the Code of FederalRegulations (CFR) in the Standard are to the January 1, 2009 edition of the CFR.

American National Standard for Hazardous Workplace Chemicals – Hazard Evaluation and Safety Data Sheet and Precautionary Labeling Preparation

SANS 11014:2010 化学药品用安全数据表．第1部分：内容和章节顺序

Presents information for the compilation and completion of an SDS. It defines specifically the general layout of the SDS, the 16 standard headings, the numbering and the sequence of these 16 standard headings and the items necessary to fill in an SDS wit

Safety data sheet for chemical products - Content and order of sections

ASTM F1525/F1525M-09 减轻危险化学品泄漏中膜片技术的应用标准指南

General8212;This guide contains information regarding the use of membrane technology to recover and concentrate hazardous materials that have entered surface and ground water as the result of a spill. Membrane technology may be applied alone or in conjunction with other treatment techniques, as follows: Different types of membrane are used in series with filters to treat highly contaminated solutions reaching concentration levels of several parts per million of organic and inorganic materials. Different types of membranes are applied in series to treat very dilute concentrations (parts per billion level) of organic and inorganic compounds. Each membrane type has the ability to remove specific compounds, thus producing a concentrated fraction. This fraction may require final off-site treatment but provides a significant reduction in transportation costs due to the large volume reduction achieved. Membranes may be used in conjunction with destruction technologies such as advanced oxidation processes (AOPs). This method is recommended for dilute solutions. The membrane technology portion concentrates the compounds to an optimum level for AOP destruction.1.1 This guide covers considerations for the use of membrane technology in the mitigation of dilute concentrations of spilled chemicals into ground and surface waters. 1.2 This guide addresses the application of membrane technology alone or in conjunction with other technologies. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. In addition, it is the responsibility of the user to ensure that such activity takes place under the control and direction of a qualified person with full knowledge of any potential or appropriate safety and health protocols.

Standard Guide for Use of Membrane Technology in Mitigating Hazardous Chemical Spills

AQ/T 3017-2008 合成氨生产企业安全标准化实施指南

本标准规定了合成氨生产企业（以下简称企业）开展安全标准化的技术要求。 本标准适用于中华人民共和国境内采用合成工艺生产氨、甲醇及其衍生产品的企业。

Guidelines for safety standardization of ammonia enterprise