G18 煤焦油加工产品 标准查询与下载

BS EN 14266:2003 煤热解衍生物.煤焦油及沥青基粘合剂及相关产品.涂覆焦油.特性及试验方法

This European Standard specifies the methods of test required to determine the characteristics for "coating tar" used for coating. Depending on the required application and the desired properties of the end product, different grades of coating tars are available.

Derivatives from coal pyrolysis - Coal tar and pitch based binders and related products - Coating tar - Characteristics and test methods

BS EN 13991:2003 煤热解衍生物.煤焦油基油.杂酚油.规范和试验方法

This European Standard gives the specifications and the test methods for creosotes for industrial wood preservation. Different grades of creosote are used depending on the desired properties of the treated wood. WARNING—The use of this European Standard may involve hazardous materials, operations and equipment. This standard cannot address all of the safety implications associated with its use. It is the responsibility of the user of this standard to establish appropriate health and safety practices and assess the applicability of regulatory limitations prior to use. The warnings to use are covered in annex C.

Derivatives from coal pyrolysis - Coal tar based oils - Creosotes - Specifications and test methods

ASTM D6945-03 乳化的精制煤焦油的标准规范(现成品、商用级)

1.1 This specification covers mineral-colloid-stabilized, emulsified refined coal tar suitable for use as a weather-protective and petroleum (aliphatic) solvent resistant coating. This product is typically applied to commercial lots and other low speed bituminous concrete pavements suitable for protection.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Emulsified Refined Coal-Tar (Ready to Use, Commercial Grade)

ASTM D6945/D6945M-03(2011)e1 乳化精炼煤焦油标准规范(成品,商品级)

1.1 This specification covers mineral-colloid-stabilized, emulsified refined coal tar suitable for use as a weather-protective and petroleum (aliphatic) solvent resistant coating. This product is typically applied to commercial lots and other low speed bituminous concrete pavements suitable for protection. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Emulsified Refined Coal-Tar (Ready to Use, Commercial Grade)

ASTM D6948/D6948M-03(2011)e1 精炼煤焦油应用的标准操作规程(成品,商品级)

This practice is designed as a guide for architects, engineers, property owners or their representatives, or combination thereof. Its use helps ensure the satisfactory performance of the protective coating system when applied over bituminous concrete pavements.1.1 This practice covers the application of emulsified refined coal tar slurry meeting the requirements of Specification D6945 Types I and II, by mechanized equipment as a weather protection and petroleum (aliphatic) solvent resistant sealer for use on bituminous concrete pavements. In order to clarify the differences between Types I and II, see 3.3 for standard definition of terms. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Application of Refined Coal Tar (Ready to Use, Commercial Grade)

ASTM D6946-03 乳化的精制煤焦油的标准规范(公路密封剂、现成品、主要为住宅级)

1.1 This specification covers mineral-colloid-stabilized, emulsified refined coal tar suitable for use as a weather-protective and petroleum (aliphatic) solvent resistant coating over bituminous concrete pavements.1.2 Both products specified are prepackaged ready to use driveway sealers primarily for retail homeowner use.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Emulsified Refined Coal-Tar (Driveway Sealer, Ready to Use, Primarily Residential Grade)

ASTM D6948-03 精制煤焦油应用的标准实施规范(现成品、商用级)

This practice is designed as a guide for architects, engineers, property owners or their representatives, or combination thereof. Its use helps ensure the satisfactory performance of the protective coating system when applied over bituminous concrete pavements.1.1 This practice covers the application of emulsified refined coal tar slurry meeting the requirements of Specification D 6945 Types I and II, by mechanized equipment as a weather protection and petroleum (aliphatic) solvent resistant sealer for use on bituminous concrete pavements. In order to clarify the differences between Types I and II, see 3.3 for standard definition of terms.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Application of Refined Coal Tar (Ready to Use, Commercial Grade)

ASTM D6753/D6753M-02(2009) 煤焦油胶粘剂标准规范

1.1 This specification covers coal tar adhesive with or without polymer modification suitable for brush, spray, squeegee and trowel application to coal tar built up and coal tar modified bitumen membrane roofings and flashings. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Coal Tar Adhesive

ASTM D2415-98 测试煤焦油和硬沥青中灰分的标准试验方法

1.1 This test method covers the determination of the ash content of tar and pitch.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Ash in Coal Tar and Pitch

ASTM D4746-98 用加压过滤法测定焦油和硬沥青中喹啉不溶物含量的标准试验方法

1.1 This test method covers the determination of the quinoline-insoluble matter (QI) in tar and pitch by pressure filtration and gives results comparable to those obtained by Method D 2318. 1.2 Since this test method is empirical, strict adherence to all details of the procedure is necessary. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.

Standard Test Method for Determination of Quinoline Insolubles (QI) in Tar and Pitch by Pressure Filtration

ASTM D4072-98(2003)e1 测定焦油和硬沥青中甲苯不溶物质(TI)含量的标准试验方法

This test method is useful for evaluating and characterizing tars and pitches and as one element in establishing the uniformity of shipments or sources of supply.1.1 This test method covers the determination of toluene-insoluble matter (TI) in tar and pitch. 1.2 Since this test method is empirical, strict adherence to all details of the procedure is necessary. 1.3 The values stated in SI units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety concerns, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard information, see Section 7.

Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch

ASTM D4072-98 测定焦油和硬沥青中甲苯不溶物质(TI)含量的标准试验方法

1.1 This test method covers the determination of toluene-insoluble matter (TI) in tar and pitch. 1.2 Since this test method is empirical, strict adherence to all details of the procedure is necessary. 1.3 The values stated in SI units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety concerns, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard information, see Section 7.

Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch

ASTM D4715-98(2003) 测定焦油和硬沥青焦化值的试验方法(Alcan)

This test method is useful for indicating the relative coke-forming propensities and for evaluating and characterizing tars and pitches. The test method can also be used as one element in establishing the uniformity of shipments or sources of supply.1.1 This test method covers the determination of the coking value of tar and pitch having an ash content not over 0.5 %, as determined by Test Method D 2415.1.2 Coking values by this test method are higher than those obtained by Test Method D 2416. See the bias statement in Section .1.3 The values stated in inch-pound units are to be regarded as the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Coking Value of Tar and Pitch (Alcan)

ASTM D4746-98(2003)e1 用加压过滤法测定焦油和硬沥青中喹啉不溶物含量的标准试验方法

This test method is useful in evaluating and characterizing tar and pitch and as one element in establishing the uniformity of shipments and sources of supply.1.1 This test method covers the determination of the quinoline-insoluble matter (QI) in tar and pitch by pressure filtration and gives results comparable to those obtained by Method D 2318. 1.2 Since this test method is empirical, strict adherence to all details of the procedure is necessary. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.

Standard Test Method for Determination of Quinoline Insolubles (QI) in Tar and Pitch by Pressure Filtration

ASTM D4715-98 测定焦油和硬沥青焦化值的试验方法(Alcan)

1.1 This test method covers the determination of the coking value of tar and pitch having an ash content not over 0.5%, as determined by Test Method D2415. 1.2 Coking values by this test method are higher than those obtained by Test Method D 2416. See the bias statement in Section 13. 1.3 The values stated in inch-pound units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Coking Value of Tar and Pitch (Alcan)

ASTM D347-97 杂酚油,杂酚焦油和煤焦油的体积和特种比重标准修正表

1.1 These tables have been prepared by the National Institute of Standards and Technology to meet a demand from the wood preserving industry for convenient tables for reducing creosote volumes to the basis of 100176F (38176C) and for reducing specific gravity observations to the same temperature. Tables 1 and 2 give in parallel columns corrections factors for creosote and for mixtures of creosote and coal tar (up to 50% tar) designated as solution, and for coal tar. They are based on density determinations made on a selected range of domestic coke-oven tars. 1.2 Table 2 shows the volume occupied at 100176F (38176C) by a quantity of oil occupying a unit volume at the indicated temperature; for example, 1 gal of creosote measured at 120176F (49176C) will have a volume of 0.9921 gal at 100176F (38176C); thus, if the volume of creosote at 120176F (49176C) equals 10000 gal, then the volume at 100176F (38176C) equals 10000 times 0.9921 or 9921 gal. 1.3 Table 2 gives corrections for observed specific gravity which are simply made by adding them to the observed values for temperatures above 100176F (38176C) and subtracting them for temperatures below 100176F (38176C). 1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.>

Standard Tables for Volume and Specific Gravity Correction for Creosote, Creosote-Coal Tar Solution and Coal Tar

NAVY MIL-P-81237 NOTICE 1-1996 季戊四醇二油酸酯

MIL-P-81237(WP) is inactive for new design and is no longer used, except for replacement purposes.

PENTAERYTHRITOL DIOLEATE

ASTM D4312-95a(2005) 测定焦油中不可溶甲苯钛含量的试验方法.沥青快速法

This test method is useful for evaluating and characterizing tars and pitches and is one element in establishing the uniformity of shipment or sources of supply.1.1 This test method covers the determination of toluene-insoluble matter (TI) in tar and pitch.1.2 Since this test method is empirical, strict adherence to all details of the procedure is necessary.1.3 The values stated in SI units are to be regarded as standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.

Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch (Short Method)

YB/T 5173-1993 木材防腐油试验方法 流动性测定方法

Test method for wood preservative oil Fluidity determination method

YB/T 5171-1993 木材防腐油试验方法 40℃结晶物测定方法

Test method for wood preservative oil - Determination method for crystallization at 40°C