共找到 198 条与 生铁 相关的标准,共 14 页
1.1 This specification2 covers gray iron for castings suitable for pressure-containing parts for use at temperatures up to 650°F (350°C). 1.2 Classes of Iron: 1.2.1 Castings of all classes are suitable for use up to 450°F (230°C). For temperatures above 450°F and up to 650°F, only Class 40, 45, 50, 55, and 60 castings are suitable. 1.2.2 Castings of all classes are suitable for use up to 230°C. For temperatures above 230°C and up to 350°C, only Class 275, 300, 325, 350, 380, and 415 castings are suitable. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Standard Specification for Gray Iron Castings for Pressure-Containing Parts for Temperatures Up to 650°F (350°C)
A 439 Type D-2 Austenitic Ductile Iron Section VIII, Division 1
A 439 Type D-2 Austenitic Ductile Iron Section VIII, Division 1
この規格は,自然流下式の汚水,雑排水,雨水及び通気の配管に使用する排水用鋳鉄管(以下,管としュう。)について規定する。
Cast-iron drainage pipes and fittings
1.1 This specification covers malleable irons for castings made by the cupola process. 1.2 Without knowledge of casting geometry and process details, quantitative relationships cannot be stated between the properties of the iron in the various locations of a casting and those of a test bar cast from the same iron. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
Standard Specification for Cupola Malleable Iron
이 규격은 인덕터 및 트랜스포머 등 전자 기기에 사용하는 연자성용 산화철(이하 산화철이라고
Soft ferrite material classification
Foundry products. Silicon Molybdenum ferritic cast iron.
This International Standard specifies the requirements and test methods applicable to ductile iron pipes, fittings, accessories and their joints for the construction of pipelines — to convey water (e.g. potable water) or gas; — operated with or without pressure; — installed below or above ground. NOTE — In this International Standard, all pressures are relative pressures expressed in bars. This International Standard gives specifications for materials, dimensions and tolerances, mechanical properties and standard coatings of pipes, fittings and accessories. It also gives performance requirements for all components including joints. This International Standard covers pipes, fittings and accessories cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints, of a size range extending from DN 40 to DN 2 600 inclusive. It is applicable to pipes, fittings and accessories which are — manufactured with socketed, flanged or spigot ends for jointing by means of various types of gaskets which are not within the scope of this International Standard; — normally delivered internally and externally coated. note :1) 100 kPa=1 bar
Ductile iron pipes, fittings, accessories and their joints for water or gas applications
Screwed type malleable cast iron pipe fittings
Defines pig-irons and the sub-division of pig-irons into different classes.
Pig-irons - Definition and classification
이 규격은 표면처리 강판 및 강대(평강)를 냉간 성형하여 건축 및 기타 구조물으; 구조 부
Zinc-coated light gauge steels for structure
This notice should be filed in front of MIL-1-461 82, dated 23 February 1982
IRON CASTING, SPHEROIDAL GRAPHITE (EXTRA TOUGH)
Technical delivery conditions for steel castings for pressure purposes. Part 3 : steel grades for use at low temperatures.
Technical delivery conditions for steel castings for pressure purposes. Part 1 : general.
Technical deliverry conditions for steel castings for pressure purposes. Part 4 : austenitic and austenitic-ferritic steel grades.
Technical delivery conditions for steel castings for pressure purposes. Part 2 : steel grades for use at room temperature and elevated temperatures.
Inspection regulation of export pig iron
이 규격은 고온에서 사용되는 압력용기용 고강도 크롬몰리브덴강 단강품에 대하여 규정한다.
High strength chromium-molybdenum alloy steel forgings for pressure vessels under high-temperature service
Chemical analysis of ferrous materials - Determination of arsenic in steel and iron - Spectrophotometric method; German version EN 10212:1995
Grained iron with decarbonizing and lower phosphor
Cast iron. Designation of microstructure of graphite.
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号