H42 铁合金 标准查询与下载

YB/T 053-2007 包芯线

本标准规定了包芯线的产品分类、技术要求、试验方法、检验规则及包装、贮运、标志和质量证明书。 本标准适用于炼钢、铸造喂线用各种包芯线。

Cored wirws

ASTM A100-07(2018) 硅铁标准规范

1.1 This specification covers grades of ferrosilicon for steelmaking and foundry uses. 1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units (SI units) given in parentheses may be approximate. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Ferrosilicon

ASTM A100-07(2012) 硅铁合金的标准规格

1.1 This specification covers grades of ferrosilicon for steelmaking and foundry uses. 1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units (SI units) given in parentheses may be approximate.

Standard Specification for Ferrosilicon

ASTM A100-07 硅铁的标准规范

1.1 This specification covers grades of ferrosilicon for steelmaking and foundry uses. 1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units (SI units) given in parentheses may be approximate.

Standard Specification for Ferrosilicon

YB/T 008-2006 钒渣

本标准规定了钒渣的技术要求、试验方法、检验规则以及包装、运输和质量证明书。 本标准适用于从含钒铁水中提炼的钒渣。

Vanadium slag

ASTM F1684-06(2011) 低热膨胀用铁-镍和铁-镍-钴合金的标准规范

1.1 This specification covers two iron-nickel alloys and one iron-nickel-cobalt alloy, for low thermal expansion applications. The two iron-nickel alloys, both containing nominally 36 % nickel and 64 % iron, with the conventional alloy designated by UNS No. K93603, and the free-machining alloy designated as UNS No. K93050. The iron-nickel-cobalt alloy, containing nominally 32 % nickel, 5 % cobalt and 63 % iron, is designated by UNS No. K93500. This specification defines the following product forms for UNS No. K93603 and UNS No. K93500: wire, rod, bar, strip, sheet plate, and tubing. The free-machining alloy, UNS No. K93050, is defined for bar products only. Unless otherwise indicated, all articles apply to all three alloys. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This pertains only to the test method section, Section 13. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Iron-Nickel and Iron-Nickel-Cobalt Alloys for Low Thermal Expansion Applications

ASTM A550-06(2010) 铌铁合金的标准规格

1.1 This specification covers three grades of ferrocolumbium, designated Low-Alloy Steel Grade, Alloy and Stainless Steel Grade, and High-Purity Grade. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Ferrocolumbium

ASTM A550-06 铌铁合金的标准规范

1.1 This specification covers three grades of ferrocolumbium, designated Low-Alloy Steel Grade, Alloy and Stainless Steel Grade, and High-Purity Grade. 1.2 The values stated in inch-pound units are to be regarded as the standard.

Standard Specification for Ferrocolumbium

ASTM A550-06(2015) 铌铁的标准规格

1.1 This specification covers three grades of ferrocolumbium, designated Low-Alloy Steel Grade, Alloy and Stainless Steel Grade, and High-Purity Grade. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Ferrocolumbium

KS D ISO 11949:2005 冷轧电镀锡板

이 규격은 박판 또는 박판으로 연속 절단될 코일 상태의 단일 및 이중 냉간 가공 저탄소 연

Cold-reduced electrolytic tinplate

YB/T 4140-2005 微碳锰铁

本标准规定了微碳锰铁的技术要求、试验方法、检验规则和包装、储运、标志及质量证明书。 本标准适用于电硅热法生产的微碳锰铁，供冶炼低碳、低磷钢种作锰元素添加剂。

Extra low carbon ferromanganese

JIS G 4202:2005 铝铬钼钢

この規格は，熱間圧延，熱間鍛造など，熱間加工によって作られたもので，通常，更に鍛造，切削などの加工及び熱処理を施し，主として機械構造用に使用されるアルミニウムクロムモリブデン鋼鋼材(以下，鋼材という。)について規定する。

Aluminium chromium molybdenum steels

YB/T 4136-2005 锰氮合金

本标准规定了锰氮合金的技术要求、试验方法、检验规则、包装、贮运、标志和质量证明书。 本标准适用于炼钢和铸造中作为氮、锰元素添加剂的氮化锰铁和氮化金属锰。

Manganese-nitrogen alloy

YB/T 4135-2005 高氮铬铁

本标准规定了高氮铬铁的技术要求、试验方法、检验规则、包装、贮运、标志和质量证明书。 本标准适用于炼钢和铸造中作为氮、铬元素添加剂的高氮铬铁。

Nitride ferrochrome with high nitrogen content

ASTM A323-05(2015) 硼铁的标准规格

1.1 This specification covers several grades of ferroboron. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.

Standard Specification for Ferroboron

ASTM A323-05(2010) 硼铁的标准规范

1.1 This specification covers several grades of ferroboron. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.

Standard Specification for Ferroboron

ASTM F256-05 含有18%或26%铬的铬铁焊接用合金的标准规范

1.1 This specification covers two chromium-iron alloys, the former, (UNS K91800), nominally 18 % chromium, balance iron, the latter, (UNS K92801), nominally 28 % chromium, in strip, bar, wire, and rod forms intended primarily for sealing to glass in electronic applications.Note 1UNS K92801 should only be considered for use at service temperatures below 300C. The alloy is prone to sigma phase formation and associated brittle mechanical behavior after prolonged exposures at temperatures close to 475C.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.The following hazard caveat pertains only to the test method portion, Sections and , of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chromium-Iron Sealing Alloys with 18 or 28 Percent Chromium

ASTM F256-05(2010) 含有18%或26%铬的铬铁密封合金的标准规范

1.1 This specification covers two chromium-iron alloys, the former, (UNS K91800), nominally 18 % chromium, balance iron, the latter, (UNS K92801), nominally 28 % chromium, in strip, bar, wire, and rod forms intended primarily for sealing to glass in electronic applications. Note 18212;UNS K92801 should only be considered for use at service temperatures below 300°C. The alloy is prone to sigma phase formation at temperatures close to 620°C, and exhibits brittle mechanical behavior after prolonged exposures at temperatures close to 475°C. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following hazard caveat pertains only to the test method portion, Sections 16 and 17, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chromium-Iron Sealing Alloys with 18 or 28 Percent Chromium

ASTM F256-05e1 含有18%或26%铬的铬铁焊接用合金的标准规范

1.1 This specification covers two chromium-iron alloys, the former, (UNS K91800), nominally 18 % chromium, balance iron, the latter, (UNS K92801), nominally 28 % chromium, in strip, bar, wire, and rod forms intended primarily for sealing to glass in electronic applications.Note 18212;UNS K92801 should only be considered for use at service temperatures below 300176;C. The alloy is prone to sigma phase formation at temperatures close to 620176;C, and exhibits brittle mechanical behavior after prolonged exposures at temperatures close to 475176;C.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The following hazard caveat pertains only to the test method portion, Sections 16 and 17, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chromium-Iron Sealing Alloys with 18 or 28 Percent Chromium

ASTM A482-05(2010) 铬铁硅标准规范

1.1 This specification covers several grades of ferrochrome-silicon.

Standard Specification for Ferrochrome-Silicon