H52 铁道用钢 标准查询与下载

GB/T 184-1963 每米50公斤钢轨用鱼尾板型式尺寸

每米50公斤鋼轨用魚尾鈑 型式尺寸

Fish-plates for 50kg/m steel rails

GB/T 182-1963 每米43公斤钢轨型式尺寸

43 kg/m Steel rails

GB 183-1963 每米38公斤钢轨型式尺寸

每米38公斤鋼轨 型式尺寸

38kg/m steel rails

GB 182-1963 每米43公斤钢轨型式尺寸

每米43公斤鋼轨 型式尺寸

43kg/m steel rails

GB/T 181-1963 每米50公斤钢轨型式尺寸

50 kg/m Steel rails

GB/T 183-1963 每米38公斤钢轨型式尺寸

38 kg/m Steel rails

YB/T 4974-2022 热轧钢轨枕

本文件规定了热轧钢轨枕的术语和定义、订货内容、型号及表示方法、截面尺寸、重量及允许偏差、技术要求、试验方法、检验规则、包装、标志及质量证明书。 本文件适用于热轧钢轨枕用型钢。

Hot rolled steel sleepers

SN/T 5301-2021 进口钢轨钢检验规程

Inspection regulations for imported rail steel

YB/T 4797-2020 重载铁路辙叉用钢

Steel for heavy-duty railway frogs

YB/T 4653-2018 城市有轨电车用槽型钢轨

Channel rails for urban trams

ASTM A729/A729M-17 公共运输和电气铁路运输用热处理碳素合金钢轴的标准规格

1.1 This specification covers heat-treated carbon and alloy steel axles for mass transit and commuter cars in electric and locomotive hauled railway service. 1.2 This specification is for solid design roller bearing axles with machined bodies. 1.3 Various axle designs are used for this service including motor and non-motor with either inboard or outboard journals. 1.4 Supplementary requirements including those in the general requirements of Specification A788/A788M are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.5 Unless the order specifies the applicable “M” specification designation, the axles shall be furnished to the inch-pound units. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Carbon and Alloy Steel Axles, Heat-Treated, for Mass Transit and Electric Railway Service

SN/T 3358-2012 旧铁路用钢检验鉴定规程

本标准规定了进口旧铁路用钢的检验鉴定、结果判定和处置。 本标准适用于进口旧铁路用钢的检验和鉴定。 本标准不适用于长度在1m以下，或者经扭曲变形的旧铁路钢轨。

Rules for the inspection of used steel for railway

ASTM A729/A729M-09e1 用于公共交通及电气化铁路的热处理合金钢轴的标准规格

1.1 This specification covers heat-treated alloy steel axles for mass transit and commuter cars in electric and locomotive hauled railway service. 1.2 This specification is for solid design roller bearing axles with machined bodies. 1.3 Various axle designs are used for this service including motor and non-motor with either inboard or outboard journals. 1.4 Supplementary requirements including those in the general requirements of Specification A788/A788M are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.5 Unless the order specifies the applicable “M” specification designation, the axles shall be furnished to the inch-pound units. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Alloy Steel Axles, Heat-Treated, for Mass Transit and Electric Railway Service

ASTM A729/A729M-09 公共运输和电气铁路运输用热处理合金钢轴的标准规范

1.1 This specification covers heat-treated alloy steel axles for mass transit and commuter cars in electric and locomotive hauled railway service. 1.2 This specification is for solid design roller bearing axles with machined bodies. 1.3 Various axle designs are used for this service including motor and non-motor with either inboard or outboard journals. 1.4 Supplementary requirements including those in the general requirements of Specification A 788/A 788M are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.5 Unless the order specifies the applicable “M” specification designation, the axles shall be furnished to the inch-pound units. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Alloy Steel Axles, Heat-Treated, for Mass Transit and Electric Railway Service

ASTM A551/A551M-08 铁路和高速交通用碳钢轮胎的标准规范

1.1 This specification covers seven classes of carbon steel tires for railway and rapid transit use. 1.1.1 Class A8212;For untreated driving tires for locomotives in passenger service. 1.1.2 Class AHT8212;For heat-treated driving tires for locomotives in passenger service. 1.1.3 Class B8212;For untreated driving tires for freight locomotives and tires for locomotive-truck, tender-truck, trailer and car wheels, and miscellaneous service. 1.1.4 Class BHT8212;For heat-treated driving tires for freight locomotives and tires for trailer wheels. 1.1.5 Class C8212;For untreated tires for switching locomotives. 1.1.6 Class CHT8212;For heat-treated driving tires and switching locomotives and tires for locomotive-trucks, tender-trucks, trailer and car wheels, and miscellaneous service. 1.1.7 Class DHT8212;For heat-treated driving tires for locomotives with light braking conditions, heavily loaded trailer tires, and rapid transit wheels where off-tread brakes are employed. 1.2 Supplementary requirements, including those in the general requirements of Specification A 788/A 788M, are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.3 The values stated in either inch-pound or SI (metric) units are to be regarded separately as standards. Within the text and tables the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.4 Unless the order specifies the applicable “M” specification designation, the tires shall be furnished to the inch-pound units.

Standard Specification for Carbon Steel Tires for Railway and Rapid Transit Applications

JB/T 10543-2006 钢轨固定装置

本标准规定了HDGY型和WJK型钢轨固定装置和SGL型钢轨对接装置的型式、尺寸、技术要求、验收规则、标志、包装与贮存。 本标准适用于YB/（T）68规定的38kg/m,43kg/m,50kg/m铁路用钢轨和YB/T 5055规定的QU70、QU80、QU100、QU120起重机钢轨的固定和对接。

Permanent unit of steel rails

YB/T 2010-2003 铁路轨距档板用热轧型钢

本标准规定了熱軋軌距朱板型鋼的型號、訂貨內容、尺寸，外形质量及允许偏差技术要求、试验方 法、检验规则、包装，标志及质量证明书。 本标准适用于 50 kg/m、60 kg/m 钢轨弹条 I 型、I 型扣件用熱軋軌距朱板型鋼(以下簡稱朱板 钢) 。

Hot-rolled sections for fastenner of rail

ASTM A2-02 平型、带槽和防护型碳素钢平底轨道的标准规范

1.1 This specification covers carbon steel girder rails of three classes based on type or type and weight, and chemistry defined as follows and in Table 1: 1.1.1 Unless otherwise specified by the purchaser, girder-guard rails shall be Class A. 1.1.2 Plain and grooved-girder rails under 135 lb/yd (67.1 kg/m) in weight shall be specified by the purchaser as either Class A or Class B. 1.1.3 Plain and grooved-girder rails of 135 lb/yd in weight and heavier shall be Class C, unless otherwise specified. 1.2 The values states in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Carbon Steel Girder Rails of Plain, Grooved, and Guard Types

ASTM A2-02(2008) 普通型、带槽和防护型碳素工字钢轨的标准规格

1.1 This specification covers carbon steel girder rails of three classes based on type or type and weight, and chemistry defined as follows and in Table 1. 1.1.1 Unless otherwise specified by the purchaser, girder-guard rails shall be Class A. 1.1.2 Plain and grooved-girder rails under 135 lb/yd (67.1 kg/m) in weight shall be specified by the purchaser as either Class A or Class B. 1.1.3 Plain and grooved-girder rails of 135 lb/yd in weight and heavier shall be Class C, unless otherwise specified. 1.2 The values states in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Carbon Steel Girder Rails of Plain, Grooved, and Guard Types

ASTM A66-01 钢螺纹钉的标准规范

1.1 This specification covers steel screw spikes used as fastenings between railroad rails, tie plates, and ties. 1.2 Supplementary Requirement S1 Specifying Copper Content is provided. It shall apply only when specified by the purchaser. 1.3 The values stated in inch-pound units are to be regarded as the standard.

Standard Specification for Steel Screw Spikes