共找到 521 条与 通用零部件综合 相关的标准,共 35 页
이 표준은 스크루 호칭 ST2.2~ST8의 와셔붙이 6각 태핑 스크루에 대하여 규정한다.
Hexagon washer head tapping screws
Calculation of load capacity of shafts and axles - Part 3: Strength of materials, Corrigendum to DIN 743-3:2012-12
이 표준은 증기ㆍ공기ㆍ물ㆍ기름 등의 스테인리스 배관에 사용하는 강관을 접속하는 강제 용접식 플랜지(이하 플랜지라 한다.)로서, 호칭 압력(기호) 5 K, 10 K, 20 K, 30 K의 플랜지에 대하여 규정한다.
Stainless steel welding flanges
이 표준은 컨테이너 스프레더(spreader) 및 그래플러 암(grappler arm)의 상태를 보여주는 표시등에대한 요구사항을 규정하며 다음과 같은 장치에 적용한다.a) 잠금장치가 장착된 무부하 및/또는 부하 상태의 컨테이너 작업용 스프레더b) 세미 트레일러 및 교체작업을 위한 그래플러 암다음의 지게차에 장착된다.― 마스트를 장착한 카운터 밸런스 지게차(KS B ISO 5053의 3.1.3.1.1 참조)― 측면 지게차(KS B ISO 5053의 3.1.3.1.7 참조)― 마스트 장착 험지용 지게차(KS B ISO 5053의 3.1.3.1.8 참조) 또는― 다방향 리치 지게차
Industrial trucks-Specification for indicator lights for container handling and grappler arm operations
This Standard establishes requirements for cast copper alloy, wrought copper, and wrought copper alloy, press-connect pressure fittings for use with hard drawn seamless copper water tube conforming to ASTM B88 for piping systems conveying water. The press-connect system (tube, fitting and joint) conforming to this standard is for use at a maximum pressure of 1380 kPa (200 psi) over the temperature range from 0°C to 93°C (32°F to 200°F). This Standard provides requirements for fittings suitable for press-connect joining and covers size designations, pressure-temperature ratings, terminology, dimensions and tolerances, materials, design qualification, required installation instructions, and markings.
Copper and Copper Alloy Press-Connect Pressure Fittings
이 표준은 일반적으로 사용하는 강제의 용접 볼트(이하 볼트라 한다.)에 대하여 규정한다.
Weld bolts
이 표준은 일반적으로 사용하는 강제 플랜지붙이 6각 볼트(이하 볼트라 한다.)에 대하여 규
Hexagon bolts with flange
이 표준은 T 홈에 끼워서 사용하는 강제 T 홈 너트(이하 너트라 한다.)에 대하여 규정한
T-slot nuts
이 표준은 T 홈에 끼워 맞추어 사용하는 강제의 T 홈용 4각 볼트(이하 볼트라 한다.)에
t half dasg slots bolts
이 표준은 일반적으로 사용하는 강제 및 황동제의 와셔 조립 +자 홈붙이 스크루에 대하여 규
Cross recessed head screws with captive washer
이 표준은 일반적으로 사용하는 강제 및 황동제의 와셔 조립 6각 볼트에 대하여 규정한다.
Hexagon head screws with captive washer
이 표준은 와이어, 바 및 튜브 인발용 다이스(이하 다이스라 한다.)의 종류별 모양 및 치
Wire, bar and tube drawing dies; Specifications
이 표준은 프레스 금형에 사용하는 다이 세트에 대하여 규정한다.
Tools for pressing-Die sets
이 표준은 단열판 없이 사출 성형기에 금형을 설치하기 위한 로케이팅 링에 대하여 규정한다.
Tools for moulding-Locating rings-Part 1:Locating rings for mounting without thermal insulating sheets in small or medium moulds-Types A and B
이 표준은 프레스 금형에서 사용하는 U 및 V 블록 가이드 플레이트의 치수 및 공차에 대하
Tools for pressing-Guide plates-U and V blocks
KS B ISO 15143의 이 부분은 KS B ISO 15143-1에서 명시된 대로 작업
Earth-moving machinery and mobile road construction machinery-Worksite data exchange-Part 2:Data dictionary
KS B ISO 15143의 이 표준은, 정보-제어 건설 작업을 하는 작업장에서 토공작업
Earth-moving machinery and mobile road construction machinery-Worksite data exchange-Part 1:System architecture
Calculation of load capacity of shafts and axles - Part 2: Theoretical stress concentration factors and fatigue notch factors
Calculation of load capacity of shafts and axles - Supplement 2: Examples to part 4
Calculation of load capacity of shafts and axles - Part 3: Strength of materials
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号