J10 通用零部件综合 标准查询与下载

KS B 1067-2009 六角半圆凹头螺栓

이 표준은 일반적으로 사용하는 강제의 6각 구멍붙이 버튼 볼트(이하, 볼트라고 한다.)에

Hexagon socket button head screws

KS B 1419-2009 双螺距输送机滚轴链、附件及链轮齿

이 표준은 일반적으로 컨베이어에 사용하는 더블 피치 롤러 체인(이하 더블 피치 체인이라고

Double-pitch conveyor roller chains, attachments and sprocket

KS B ISO 15871:2009 工业车辆.集装箱搬运和抓斗臂操作用指示灯规范

이 표준은 컨테이너 스프레더(spreader) 및 그래플러 암(grappler arm)의

Industrial trucks-Specification for indicator lights for container handling and grappler arm operations

KS B 1427-2009 成型塑料齿轮精密度

이 표준은 정면 모듈 0.2 mm 이상, 1.6 mm 이하, 피치원 지름 1.5∼200 m

Accuracy system of injection molded plastic cylindrical gears

KS B 1068-2009 普通扭矩型钢螺母的机械性质及性能

이 표준은 일반적으로 사용하는 프리베일링 토크형 풀림 방지 강제 너트)로, 표 1의 적용

Mechanical and performance properties for prevailing torque type steel nuts

KS B 1347-2009 同步环

이 표준은 차량용 수동 변속기의 싱크로나이저 링(이하 링이라고 한다.)에 대하여 규정한다.

Synchronizer ring

KS B ISO 14635-3:2009 齿轮.FZG试验程序.第3部分:半流齿轮润滑脂压塑性变形承载能力和耐磨性用A/2、8/50 FZG试验方法

이 표준은 스커핑(scuffing)이라는 기어 치면 손상으로 정의되는 기어용 그리스의 상대

Gears-FZG test procedures-Part 3:FZG test method A/2.8/50 for relative scuffing load-carrying capacity and wear characteristics of semifluid gear greases

KS B ISO 16860:2009 液压传动.过滤器.差压装置试验方法

이 표준은 유압유체 동력 필터에 부속 장치로 사용되는 차압 또는 바이패스 밸브 상태 알림

Hydraulic fluid power－Filters－Test method for differential pressure devices

KS B 1072-2009 六角一字槽螺钉

이 표준은 6각 머리 및 일자홈 캡 스크루(이하 “스크루”라 한다.)에 대하여 규정한다.

Slotted and hexagon head cap screws

KS B ISO 16111:2009 便携式储气装置.可逆性金属氢化物吸收的氢

이 표준은 차단밸브 압력방출장치(Pressure-relief devices, PRD) 등

Transportable gas storage devices－Hydrogen absorbed in reversible metal hydride

KS B 1326-2009 平垫圈

이 표준은 일반용의 볼트, 너트, 작은 나사 등에 사용하는 강제, 스테인리스 강제 및 황동

Plain washers

KS B 1070-2009 狭槽、十字槽及六角头机器螺钉

이 표준은 일자홈, 십자홈 및 6각 머리 머신 스크루(이하 “스크루”라 한다.)에 대하여

Slotted, cross-recessed or hexagon head machine screws

KS B ISO 14635-2:2009 齿轮.FZG试验程序.第2部分:测试高极压齿轮油压塑性变形承载能力用的A10/16、6R/120 FZG分步负载试验

이 표준은 스커핑(scuffing)이라는 기어 치면 손상에 의해 규정되는 고극압(EP)유의

Gear-FZG test procedures-Part 2:FZG step load test A10/16,6R/120 for relative scuffing load-carrying capacity of high EP oils

KS B ISO 14635-1:2009 齿轮.FZG试验程序.第1部分:测试齿轮油压塑性变形承载能力用的A/8、3/90 FZG试验方法

이 표준은 스커핑(scuffing)이라는 기어 치면 손상으로 정의되는 윤활제의 상대 부하

Gears-FZG test procedures-Part 1:FZG test method A/8,3/90 for relative scuffing load-carrying capacity of oils

KS B ISO 1224-2:2009 滚动轴承.仪器精密轴承.第2部分:英寸系列轴承边界尺寸、公差和特征

이 표준은 정밀 기기 구름 베어링의 특성, 즉 인치계열, 종류, 경계치수, 공차 및 내부틈

Rolling bearings-Instrument precision bearings-Part 2:Boundary dimensions, tolerances and characteristics of inch series bearings

KS B ISO 1224-1:2009 滚动轴承.仪器精密轴承.第1部分:米制系列轴承边界尺寸、公差和特征

이 표준은 정밀 기기 구름 베어링의 특성, 즉 미터계열, 종류, 경계치수, 공차 및 내부틈

Rolling bearings－Instrument precision bearings－Part 1：Boundary dimensions, tolerances and characteristics of metric series bearings

BS 10:2009 管子,阀门和配件用法兰和螺栓连接规范

This British Standard specifies requirements for a series of carbon steel, alloy steel, cast iron and copper alloy flanges, and also appropriate bolts and nuts, for use with pipes, valves and fittings containing steam, oil, compressed air or water. NOTE 1 The use of flanges complying with this standard for temperatures below −17.8 °C (0 °F) should be agreed between purchaser and manufacturer. These flanges may also be used on pipes, valves and fittings carrying other fluids for which the same requirements for safety and joint tightness are appropriate. The applicability relationship between temperature and pressure for the above materials is specified for each table of flanges in Table 2 and Annex B. NOTE 2 The types of gasket, and gasket materials, and the surface finish of the jointing face are matters for agreement between the purchaser and the manufacturer. When a raised jointing face is specified the outside diameter of the gasket should extend at least to the outside diameter of the raised face. For steel flanges when a raised jointing face is not specified, the gasket should be within the bolt holes.

Specification for flanges and bolting for pipes, valves and fittings

BS EN ISO 1179-3:2008 通用和液压传动用连接件.带弹性体密封件或金属对金属密封件的ISO 228-1螺纹端口和螺柱端头.带扣环O型密封圈(G型和H型)密封的轻型(L系列)螺柱端头

This part of ISO 1179 specifies dimensions, performance requirements and test procedures for non-adjustable and adjustable light-duty (L series) stud ends with ISO 228-1 threads with sealing by O-ring with retaining ring (types G and H, respectively). Light-duty (L series) stud ends in accordance with this part of ISO 1179 may be used at working pressures up to 31,5 MPa (315 bar) for non-adjustable stud ends (type G) and up to 20 MPa (200 bar) for adjustable stud ends (type H). The permissible working pressure depends upon size, materials, design, working conditions, application, etc. Conformance to the dimensional information in this part of ISO 1179 does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this part of ISO 1179 to assure that components made to this part of ISO 1179 comply with the performance ratings.

Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H)

ASME Y14.8-2009 铸件、锻件，和模制零部件

This Standard covers definitions of terms and features unique to casting, forging, and molded part technologies with recommendations for their uniform specification on engineering drawings and related documents. Unless otherwise specified, any reference to features, parts, or processes shall be interpreted as applying to castings, forgings, and molded parts. Castings, forgings, and molded parts are delineated as "parts" throughout the Standard.

Casting, Forgings, and Molded Parts

KS B 1060-2008 钻孔机自攻螺纹

이 표준은 일반적으로 강제 드릴링 태핑 스크루(이하 강 드릴링 스크루라 한다.) 및 마르텐

Self drilling tapping screws