J10 通用零部件综合 标准查询与下载

ANSI/ITSDF B56.11.1-2012 双轴承圈或双旋转节和刚性工业自位轮

Double Race or Bi-Level Swivel and Rigid Industrial Casters

ASTM A961/A961M-12 管道设施用钢法兰,锻件,阀门和部件通用要求的标准规格

1.1 This specification covers a group of common requirements that shall apply to steel flanges, forged fittings, valves, and parts for piping applications under any of the following individual product specifications: Title of Specification ASTM Designation Forgings, Carbon Steel, for Piping Components A105/A105M Forgings, Carbon Steel, for General-Purpose Piping A181/A181M Forged or Rolled Alloy-Steel Pipe Flanges, Forged A182/A182M Fittings, and Valves and Parts for High Temperature Service Forgings, Carbon and Low Alloy Steel, Requiring Notch A350/A350M Toughness Testing for Piping Components Forged or Rolled 8 and 9 % Nickel Alloy A522/A522M Steel Flanges, Fittings, Valves, and Parts for Low-Temperature Service Forgings, Carbon and Alloy Steel, for Pipe Flanges, A694/A694M Fittings, Valves, and Parts for High-Pressure Transmission Service Flanges, Forged, Carbon and Alloy Steel for Low A707/A707M Temperature Service Forgings, Carbon Steel, for Piping Components with A727/A727M Inherent Notch Toughness Forgings, Titanium-Stabilized Carbon Steel, for A836/A836M Glass-Lined Piping and Pressure Vessel Service 1.2 In case of conflict between a requirement of the individual product specification and a requirement of this general requirement specification, the requirements of the individual product specification shall prevail over those of this specification. 1.3 By mutual agreement between ......

Standard Specification for Common Requirements for Steel Flanges, Forged Fittings, Valves, and Parts for Piping Applications

ASTM A182/A182M-12a 高温设施用锻造或轧制合金和不锈钢管法兰、锻制配件、和阀门及部件的标准规格

1.1 This specification2 covers forged low alloy and stainless steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts to specified dimensions or to dimensional standards, such as the ASME specifications that are referenced in Section 2. 1.2 For bars and products machined directly from bar (other than those directly addressed by this specification; see 6.4), refer to Specifications A479/A479M and A739 for the similar grades available in those specifications. Products made to this specification are limited to a maximum weight of 108201;000 lb [4540 kg]. For larger products and products for other applications, refer to Specifications A336/A336M and A965/A965M for the similar ferritic and austenitic grades, respectively, available in those specifications. 1.3 Several grades of low alloy steels and ferritic, martensitic, austenitic, and ferritic-austenitic stainless steels are included in this specification. Selection will depend upon design and service requirements. Several of the ferritic/austenitic (duplex) grades are also found in Specification A1049/A1049M. 1.4 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.5 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable ???M??? specification designation (SI units), the material shall be furnished to inch-pound units. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service

KS B ISO 11342:2011 机械振动.挠性转子机械平衡捕捉的方法和标准

이 표준은 그 특성과 요구되는 평형 정도에 따라 대표적인 연성 회전체 형태를 제시하고, 평

Mechanical vibration-Methods and criteria for the mechanical balancing of flexible rotors

KS B ISO 16039:2011 道路建设和维护设备.滑模铺料机.定义和商业规范

이 표준은 일반적인 명칭으로 “슬립폼 페이버”이고, 소성 상태의 콘크리트를 성형하여 시멘트

Road construction and maintenance equipment-Slipform pavers-Definitions and commercial specifications

KS B 1073-2011 无头六角孔及花键定位螺钉

이 표준은 무두 6각 소켓 및 스플라인 소켓 세트스크루(이하, “세트스크루”라 한다.)에

Headless hexagon socket and spline socket setscrews

ASTM A182/A182M-11 高温设施用锻造或轧制合金和不锈钢管法兰,锻制配件,和阀门及部件的标准规格

1.1 This specification covers forged low alloy and stainless steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts to specified dimensions or to dimensional standards, such as the ASME specifications that are referenced in Section 2. 1.2 For bars and products machined directly from bar (other than those directly addressed by this specification; see 6.4), refer to Specifications A479/A479M and A739 for the similar grades available in those specifications. Products made to this specification are limited to a maximum weight of 10 000 lb [4540 kg]. For larger products and products for other applications, refer to Specifications A336/A336M and A965/A965M for the similar ferritic and austenitic grades, respectively, available in those specifications. 1.3 Several grades of low alloy steels and ferritic, martensitic, austenitic, and ferritic-austenitic stainless steels are included in this specification. Selection will depend upon design and service requirements. Several of the ferritic/austenitic (duplex) grades are also found in Specification A1049/A1049M. 1.4 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.5 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service

ASTM A989/A989M-11 高温设备用热等静压压制的合金钢法兰,配件,阀门和部件的标准规格

1.1 This specification covers hot isostatically-pressed, powder metallurgy, alloy steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts made to specified dimensions or to dimensional standards, such as in ASME Specification B16.5. 1.2 Several grades of alloy steels are included in this specification. 1.3 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.4 This specification is expressed in both inch-pound units and in SI units. Unless the order specifies the applicable “M” specification designation (SI units), however, the material shall be furnished to inch-pound units. 1.5 The values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.6 The following safety hazards caveat pertains only to test methods portions, 8.1, 8.2, and 9.5-9.7 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Standard Specification for Hot Isostatically-Pressed Alloy Steel Flanges, Fittings, Valves, and Parts for High Temperature Service

ASTM A988/A988M-11 高温下使用的热等静加压成形的不锈钢法兰盘,管配件,阀及零件的标准规格

1.1 This specification covers hot isostatically-pressed, powder metallurgy, stainless steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts made to specified dimensions or to dimensional standards, such as in ASME specification B16.5. 1.2 Several grades of martensitic, austenitic, age hardening, and austenitic-ferritic stainless steels are included in this specification. 1.3 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.4 This specification is expressed in both inch-pound units and in SI units. Unless the order specifies the applicable “M” specification designation (SI units), however, the material shall be furnished to inch-pound units. 1.5 The values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in parentheses. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 The following safety hazards caveat pertains only to test methods portions 8.1, 8.2, 9.5-9.7, and Section 10 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Hot Isostatically-Pressed Stainless Steel Flanges, Fittings, Valves, and Parts for High Temperature Service

ASTM A961/A961M-11 管道设施用钢法兰,锻件,阀门和部件的通用要求的标准规格

1.1 This specification covers a group of common requirements that shall apply to steel flanges, forged fittings, valves, and parts for piping applications under any of the following individual product specifications:

Standard Specification for Common Requirements for Steel Flanges, Forged Fittings, Valves, and Parts for Piping Applications

KS B ISO 1234:2010 开口销

이 표준은 분할 핀에 대하여 규정한다.

Split pins

KS B ISO 12240-1:2010 关节轴承.第1部分:径向球面滑动轴承

이 표준은 (KS B) ISO 12240 중에서 레이디얼 스페리컬 미끄럼 베어링(이하 베어

Spherical plain bearings-Part 1:Radial spherical plain bearings

KS B ISO 113:2010 滚动轴承附件轴承座外形尺寸

이 표준은 ISO 15에서 규정된 지름 계열 0, 1, 2, 3에서 주로 구름베어링에 대한

Rolling bearings-Plummer block housings

KS B 1324-2010 弹簧防松垫圈

이 표준은 일반용 볼트ㆍ작은 나사 등에 사용하는 강제, 스테인리스 강제 및 인청동제의 스

Spring lock washers

KS B ISO 16156:2010 机床安全性.工件夹具用卡盘的设计和建造的安全性要求

이 표준은 공작기계의 공작물 고정척에 대한 위험을 제거하고 제한하기 위한 요건과 측정 방법

Machine-tools safety-Safety requirements for the design and construction of work holding chucks

DB13/T 1239-2010 潜孔钻机和钻凿机械通用技术条件

本标准规定了潜孔钻机和钻凿机械产品应遵循的通用技术规范。其内容包括该类机械产品的术语和定义、型号命名要求、安全要求、通用技术要求、试验方法、检验规则和标志、包装、运输及贮存的要求。本标准适用于河北省范围内生产的潜孔钻机和钻凿机械产品。

General specifications for down-the-hole drilling rigs and drilling machinery

KS B 1016-2010 地基螺母

이 표준은 일반적으로 사용하는 강제의 기초 볼트(이하 볼트라 한다.)에 대하여 규정한다.

Foundation bolts

KS B 1045-2009 机床锁紧螺帽

이 표준은 공작 기계의 베어링 고정용으로 사용하는 공작기계용 로크 너트(이하 로크 너트라고

Lock nuts for machine tools

KS B 1347-2009 同步环

이 표준은 차량용 수동 변속기의 싱크로나이저 링(이하 링이라고 한다.)에 대하여 규정한다.

Synchronizer ring

KS B 1010-2009 摩擦接合用高张力六角螺栓、六角螺母、平垫圈组

이 표준은 주로 강 구조물에 사용하는 마찰 접합용 고장력 6각 볼트ㆍ6각 너트ㆍ평와셔의 세

Set of high strength hexagon bolt, hexagon nut and plain washers for friction grip joints