J54 钻、镗、铣床 标准查询与下载

JB/T 11571.2-2013 大型数控铣齿机 第2部分:技术条件

JB/T 11571的本部分规定了大型数控铣齿机设计、制造、检验与验收的要求。本部分适用于最大加工直径2 000 mm~5 000 mm的大型数控铣齿机(以下简称“机床”)。

Large CNC gear milling machines.Part 2: Specifications

JB/T 2254.4-2013 坐标镗床 第4部分:型式与参数

JB/T 2254的本部分规定了坐标镗床的型式与参数。本部分适用于新设计或改进设计的工作台面宽度小于或等于2000 mm的M级和P级精度等级的单柱和双柱坐标镗床。

Jig boring machines.Part 4: Types and parameters

JB/T 11579.1-2013 小型数控深孔钻床 第1部分:精度检验

JB/T 11579的本部分规定了普通精度等级的小型数控深孔钻床的精度要求及检验方法。本部分适用于钻孔直径范围为Φ1 mm~Φ50 mm、最大钻孔深度至3 000 mm的小型数控深孔钻床。

Miniature CNC deep-hole drilling machines.Part 1: Testing of the accuracy

JB/T 11579.2-2013 小型数控深孔钻床 第2部分:技术条件

JB/T 11579的本部分规定了普通精度等级的小型数控深孔钻床的制造和验收要求。本部分适用于钻孔直径范围为Φ1 mm~Φ50 mm、最大钻孔深度至3 000 mm的小型数控深孔钻床。

Miniature CNC deep-hole drilling machines.Part 2: Specifications

JB/T 11568-2013 五轴联动高架横梁移动龙门铣床 技术条件

本标准规定了五轴联动高架横梁移动龙门铣床的设计、制造和验收要求。本标准适用于工作台面宽度1 000 mm~3 000 mm的具有五个数控轴线,即三个线性轴线(X、Y、Z)和两个回转轴线(A、C)或(B、C)的五轴联动高架横梁移动龙门铣床。

Five-axis simultaneous control plano-milling machines with a traveling overhead cross rail.Specifications

KS B ISO 3070-2:2013 机床.卧式镗铣床的精度试验条件.第2部分:台式机床

Machine tools-Test conditions for testing the accuracy of boring and milling machines with horizontal spindle-Part 2:Machines with movable column and fixed table

KS B ISO 3070-3:2013 机床.卧式镗铣床的精度试验条件.第3部分:可拆卸固定工件夹具平台的板形机械

Machine tools-Test conditions for testing the accuracy of boring and milling machines with horizontal spindle-Part 3:Machines with movable column and movable table

KS B ISO 3070-1:2013 机床.卧式镗铣床的精度试验条件.第1部分:固定式机床和可移动工作台机床

Machine tools-Test conditions for testing the accuracy of boring and milling machines with horizontal spindle-Part 1:Machines with fixed column and movable table

BS ISO 3438:2013 螺纹攻丝前钻孔用阶梯麻花钻

Subland twist drills for holes prior to tapping screw threads

SAE J2583-2013 定向转孔规划和制图命名法

This SAE Standard applies to planning and mapping various types of information associated with directional boring/drilling machines. This type of planning and mapping information is typically used with horizontal earthboring machines as defined by SAE J 2022. This is a compilation of terms and definitions commonly associated with the planning and mapping of underground pipe and utility installation by using horizontal earthboring machines.

Directional Drilling Planning and Mapping Nomenclature

SAE J2520-2013 定向钻孔跟踪设备用分类、术语和规范的定义

This SAE Standard applies to directional drilling electronics and tracking equipment of the following types: a. tracking transmitter; b. tracking receiver; c. telemetry device; and d. remote display. This type of tracking equipment is typically used with horizontal earthboring machines as defined in SAE J 2022. The purpose of this document is to define common terms and commercial specifications associated with tracking equipment used in the horizontal earthboring industry.

Classification, Nomenclature, and Specification Definitions for Directional Drilling Tracking Equipment

KS B ISO 3070-4:2012 刨床卧式镗床.精度检查

이 표준은 KS B ISO 230-1과 KS B ISO 230-2에 기초하여 보통 정확정밀

Test conditions for boring and milling machines with horizontal spindle-Testing of the accuracy-Part 4:Planer type machines with movable column

KS B ISO 3190:2012 立式单轴转塔坐标钻床的验收条件.精度试验

이 표준은 KS B ISO 230-1을 기초로 하여 보통 정확정밀도를 가진 범용으로 사용하

Drilling machines(turret and single spindle) withvertical spline-Testing of the accuracy

KS B ISO 3655:2012 单柱或双柱型单一固定或可移工作台的立式车镗床验收条件.一般介绍和精度试验

이 표준은 단주 또는 문형 및 싱글 고정형 또는 이동형 테이블을 갖는 수직 터닝 및 보링

Acceptance conditions for vertical turning and boring lathes with one or two columns and a single fixed or movable table-General introduction and testing of the accuracy

KS B ISO 2772-1:2012 方柱立式钻床的检查条件.精度试验.第1部分:几何参数试验

이 표준은 KS B ISO 230-1을 기초로 일반적인 정확정밀도를 갖는 박스형 직립 드릴

Test conditions for box type vertical drilling machines-Testing of the accuracy-Part 1:Geometrical tests

JIS B 6228-2:2012 机床.桥式铣床测试条件.精度检验.第2部分:移动吊架(吊架式)机械

This Standard specifies, with reference to JIS B 6190-2, JIS B 6190-7, JIS B 6191, geometric tests, machining tests, and tests for checking accuracy and repeatability of positioning of numerically controlled axes for general-purpose normal accuracy bridge-type milling machines with a travelling bridge (gantry-type). This Standard also specifies the applicable tolerances corresponding to the above-mentioned tests.

Machine tools -- Test conditions for bridge-type milling machines -- Testing of the accuracy -- Part 2: Travelling bridge (gantry-type) machines

JIS B 6210-3 ERRATUM 1:2011 勘误表

ERRATUM

JB/T 8332.3-2011 重型深孔钻镗床.第3部分：型式与参数

JB/T 8332的本部分规定了重型深孔钻镗床的型式与参数。 本部分适用于新设计的最大镗孔直径为250mm～1000mm、工件主轴箱固定型和移动型一般用途的重型深孔钻镗床。

Heavy duty deephole drilling & boring machines.Part 3:Types and parameters

JB/T 2254.1-2011 坐标镗床.第1部分：精度检验

JB/T 2254的本部分规定了坐标镗床的几何精度、定位精度、工作精度的检验项目、方法和公差。 本部分适用于工作台面宽度小于或等于2000mm的M级和P级精度等级的单柱和双柱坐标镗床。

Jig boring machines.Part 1:Testing of the accuracy

JB/T 4367.1-2011 落地镗、落地铣镗床.第1部分：型式与参数

JB/T 4367的本部分规定了落地镗床、落地铣镗床的型式与参数。 本部分适用于新设计的镗轴直径为130mm～320mm一般用途的落地镗床、落地铣镗床。

Floor boring machines and floor milling & boring machines.Part 1:Types and parameters