J59 特种加工机床 标准查询与下载

DIN 58737-2:2001 光学加工.定心主轴.第2部分:带圆柱形夹的定心主轴

The document applies to spindles which are used in centring-machines for the production in optical engineering. The aim of the document is the standardization of consistant dimensions to enable an exchangeability to different types of machines in the field of optical engineering.

Production in optical engineering - Spindles - Part 2: Spindles with clamping cylinder

DIN 58736-3:2001 光学加工.定心罩.第3部分:外连接用圆柱形接头.尺寸12mm和25mm

The document applies to centering bells with fitting dimension 12 mm which are used in production for optical engineering. Purpose of these requirements are standardised dimensions for centering bells with cylindrical fittings 12 mm and 25 mm to enable exchangeability.

Production in optical engineering - Centering bells - Part 3: With cylindrical fitting dimension 12 mm and 25 mm for outer connection

BS EN 12478:2001 机床的安全.大型数控车床和车削中心

This European Standard specifies the requirements and/or measures to remove the hazards and limit the risks on general purpose numerically controlled large turning machines and turning centres which are designed primarily to work cold metal as defined in 3.1 and 3.2 and herein after referred to as "machines". This standard covers all significant relevant hazards which are listed in clause 4. This standard is applies to : — numerically controlled large vertical turning machines and turning centres which are equipped with work clamping plate exceeding 500 mm outside diameter. — numerically controlled horizontal spindle turning machines and turning centres with distance between centres exceeding 2 000 mm or which are equipped with work clamping devices exceeding 500 mm outside diameter. The standard also applies to ancillary devices (e.g. for workpieces, tools and work clamping devices handling devices and chip handling equipment, etc.) which are integral to the machine. This standard also applies also to machines which are integrated in an automatic production line or turning cell where the hazard and risks arising are comparable to those of machines working separately. Where additional processes are involved this standard can be taken as a basis (see also annex bibliography) This standard does apply to NC turning machines with machining facilities under manual control which are dealt with in EN 12840:2000. This standard applies to machines which are manufactured after the date of issue of this standard.

Safety of machine tools - Large numerically controlled turning machines and turning centres

ANSI B11.23-2001 组合加工中心机床和自动数控铣床、钻床和镗床的安全要求

This standard specifies the safety requirements for the design, construction, operation and maintenance (including installation, dismantling and transport) of machining centers and automatic numerically controlled milling, drilling and boring machines.

Safety Requirements for Machining Centers and Automatic Numerically Controlled Milling, Drilling and Boring Machines

ANSI B11.22-2001 旋转中心和自动数控旋转机器的安全要求

This standard specifies the safety requirements for the design, construction, operation and maintenance (including installation, dismantling and transport) of turning centers and automatic, numerically controlled turning machines.

Safety Requirements for Turning Centers and Automatic Numerically Controlled Turning Machines

NF E60-140:2000 机床.金属丝放电加工机床的试验条件.术语和准确度试验

Machine tools - Test conditions for wire electrical discharge machines (wire EDM) - Terminology and testing of the accuracy.

NF E60-134-1:2000 机床.冲模放电机器的试验条件.术语和精确度试验.第1部分:单柱机器

Machines tools - Test conditions for die sinking electro-discharge machines (EDM) - Terminology and testing of accuracy - Part 1 : single column machines (cross slide table type and fixed table type).

NF E60-134-2:2000 机床.冲模放电机器的试验条件.术语和精确度试验.第2部分:双柱机

Machines tools - Test conditions for die sinking electro-discharge machines (EDM) -Terminology and testing of the accuracy - Part 2 : two column machines (slide-head type and cross-slide table type).

JB/T 10208-2000 电火花加工机床.操作指示形象化符号

　　本标准规定了电火花加工机床用各种操作指示形象化符号。 本标准适用于电火花加工机床及其附件的操作指示标牌、操作面板和标志等。

Electro-discharge machines.Symbols for indications appearing

BS ISO 14137:2000 机床.金属线放电加工机床的试验条件.术语和准确度试验

ISO 14137 specifies, with reference to ISO 230-1, ISO 230-2 and ISO 230-4, geometric tests, tests of accuracy and repeatability of numerically controlled positioning axes, machining test and circular tests for general purpose, normal-accuracy wire electrical-discharge machines (wire EDM). It also specifies applicable tolerances correspond-ing to the above-mentioned tests. ISO 14137 is applicable to single column machines of cross slide table type and double column type machines. ISO 14137 deals only with the testing of accuracy of the machine. It does not apply to the testing of the machine operation (vibration, abnormal noise, stick-slip motion of components, etc.) nor to machine characteristics (such as speeds, feeds, etc.), which should generally be carried out before testing the accuracy. ISO 14137 provides the terminology used for the principle components of the machine and the designation of the axes in accordance with ISO 841.

Machine tools - Test conditions for wire electrical-discharge machines (wire EDM) - Terminology and testing of the accuracy

ISO 14137:2000 机床 线切割机床(EDM丝)检验条件 术语及精度检验

ISO 14137 specifies, with reference to ISO 230-1, ISO 230-2 and ISO 230-4, geometric tests, tests of accuracy and repeatability of numerically controlled positioning axes, machining test and circular tests for general purpose, normal-accuracy wire electrical-discharge machines (wire EDM). It also specifies applicable tolerances correspond-ing to the above-mentioned tests. ISO 14137 is applicable to single column machines of cross slide table type and double column type machines. ISO 14137 deals only with the testing of accuracy of the machine. It does not apply to the testing of the machine operation (vibration, abnormal noise, stick-slip motion of components, etc.) nor to machine characteristics (such as speeds, feeds, etc.), which should generally be carried out before testing the accuracy. ISO 14137 provides the terminology used for the principle components of the machine and the designation of the axes in accordance with ISO 841.

Machine tools - Test conditions for wire electrical discharge machines (wire EDM) - Terminology and testing of the accuracy

JB/T 10082-2000 电火花线切割机.技术条件

本标准规定了往复走丝（高速走丝）电火花线切割机的安全防护，加工和装配质量，机床空运转试验，机床精度检验，机床负荷试验，标志与使用说明书和包装、运输与贮存的技术要求。 本标准适用于一般用途、常规精度的模具及零件加工用的往复走丝（高速走丝）电火花线切割机。

Wire electro-discharge machines.Techenical requirements

DIN 58722-1:2000 光学工程加工.光学工程加工的定义.第1部分:工艺

The document contains terms and definitions which are used daily in production in optical engineering.

Production in optical engineering - Definitions related to production in optical engineering - Part 1: Processes

JB/T 54455-1999 电火花线切割机产品质量分等（内部使用）

Product quality grading of wire electric discharge machine (internal use)

JB/T 54827-1999 电火花成形机产品质量分等

EDM product quality classification

JIS B 6361-1:1999 机床.模具用放电加工机床(EDM)的试验条件.术语和精度检验.第1部分:单柱机(纵横移动工作台型和固定台型)

この規格は，JIS B 6191及びJIS B 6192に基づいて，普通精度のはん(汎)用シングルコラム形形彫り放電加工機(EDM)の静的精度検査，工作精度検査及び位置決め精度検査について規定する。

Machine tools -- Test conditions for die-sinking electro-discharge machines (EDM) -- Terminology and testing of accuracy -- Part 1: Single column machines (cross slide table type and fixed table type)

JIS B 6360:1999 机床.线切割加工机床(线EDM)的试验条件

Machine tools -- Test conditions for wire electrical discharge machines (wire EDM) -- Terminology and testing of the accuracy

JIS B 6361-2:1999 机床.模具用放电加工机床(EDM)的试验条件.术语和精度检验.第1部分:双柱机(滑动头型和纵横移动工作台型)

この規格は， JIS B 6191及びJIS B 6192に基づいて，普通精度のはん(汎)用門形形彫り放電加工機(EDM)の静的精度検査，工作精度検査及び位置決め精度検査について規定する。

Machine tools -- Test conditions for die-sinking electro-discharge machines (EDM) -- Terminology and testing of accuracy -- Part 2: Two column machines (slide-head type and cross-slide table type)

JB/T 10142-1999 超声抛光机 技术条件

本标准规定了超声抛光机的分类、技术要求和试验方法；还规定了超声抛光机的标志与使用说明书、包装与运输的技术要求。 本标准适用于模具及零件抛光用各类超声抛光机。

Ultrasonic buffing machines。Technical requirements

JB 10143-1999 电火花成形机用自动灭火器.技术条件

本标准规定了用于电火花成形机的自动灭火器的型号与规格，技术要求，试验方法，检验规则，标志与使用说明书，包装与贮存。 本标准适用于使用可燃性工作液的电火花成形机用自动灭火器。

Automatic fire extinguishers for die sinking electro-discharge machines.Technical requirements