J75 换热设备 标准查询与下载

BS EN 1048:2014 热交换器.空气冷化液体冷却器“干冷却器”.性能稳定性的试验方法

Heat exchangers. Air cooled liquid coolers ('dry coolers'). Test procedures for establishing the performance

EN 328:2014 热交换器-强制对流单元空气冷却器.用建立性能的试验程序

This European Standard is applicable to non-ducted unit air coolers for refrigeration operating: a) with direct dry expansion of a refrigerant; b) with liquid overfeed by pump circulation of a refrigerant; c) with a liquid. This standard specifies uniform methods of performance assessment to test and ascertain the following:- product identification; - standard capacity; - standard liquid pressure drop; - standard refrigerant pressure drop (for operation with liquid overfeed by pump circulation only); - nominal air flow rate; - nominal fan power. It does not cover evaluation of conformity. It is not applicable to air coolers for duct mounting or with natural air convection. This standard does not cover technical safety aspects.

Heat exchangers - Forced convection unit air coolers for refrigeration - Test procedures for establishing the performance

EN 327:2014 热交换器.强制对流空气冷却器.建立性能的试验程序

This European Standard applies to non-ducted forced convection air cooled refrigerant condensers/gas coolers with dry air side surface within which the refrigerant changes phases or is cooled. Its purpose is to establish uniform methods of performance assessment. It does not deal with evaluation of conformity. This European Standard does not apply to air cooled condensers/gas coolers, designed primarily for installation within the machinery compartment of packaged products or in factory-assembled condensing/gas cooling units. This European Standard does not apply to condensers with an integral subcooling part. This European Standard specifies methods to test and ascertain the following:- product identification; - standard capacity; - nominal air flow rate; - nominal fan power. This European Standard does not cover technical safety aspects.

Heat exchangers - Forced convection air cooled refrigerant condensers - Test procedures for establishing performance

JB/T 11183.2-2013 密筋式热交换器 第2部分：技术条件

Close-reinforced heat exchangers Part 2: Specifications

BS ISO 16345:2014 水冷却塔. 热性能测试和评价

Water-cooling towers. Testing and rating of thermal performance

DB35/T 1428-2014 烟气换热器经济运行评定

本标准规定了烟气换热器经济运行评定的术语和定义、基本要求、评定等要求。 本标准适用于TSG G0001规定范围内锅炉使用的烟气换热器，其他用热设备使用的烟气换热器可参照本标准。

Evaluation of Economical Operation of Flue Gas Heat Exchanger

CECS 362-2014 热源塔热泵系统应用技术规程

本规程适用于以室外空气为冷热源,以热源塔为排热和取热装置,采用蒸气压缩式热泵技术进行供冷、供热的系统工程的设计、施工安装和调试验收。热源塔热泵系统适用于冬季室外计算空气干球温度在2℃~-8℃的地区。

Technical specification for heat-source-tower heat pump system

NF E38-116-3:2013 空间加热和制冷用带电驱动压缩机的空调、液体制冷包装件和热泵.第3部分:试验方法

Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling - Part 3: test methods

YD/T 2557-2013 通信用制冷剂泵-压缩机双循环系统技术要求和试验方法

本标准规定了通信用制冷剂泵-压缩机双循环系统(以下简称“双循环空调机”)的术语和定义、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于名义制冷量大于14kW的通信用具有制冷剂泵-压缩机双循环制冷的风冷式空气调节系统。

Technical requirements and testing methods for CRAC with refrigerant pumping-compressing dual cycles

JB/T 11631-2013 换热器专用胀管机

本标准规定了换热器专用胀管机(以下简称胀管机)的术语和定义、型式及基本参数、要求、试验方法、检验规则及标志、包装、运输和贮存、本标准适用于加工换热器(由符合GB/T 17791的铜管或铝管和符合GB/T 3198的铝箔或铜泊组成)的胀管机、

Expander for heat exchanger

JB/T 11632-2013 换热器发夹型弯管机

本标准规定了换热器发夹型(长U型)弯管机(以下简称弯管机)的术语和定义、型式及基本参数、要求、试验方法、检验规则及标志、包装、运输和贮存、本标准适用于对符合GB/T 17791的铜管(或铝管),供应状态为软态(M)并经过光亮退火,对其弯曲成发夹型形状的半自动和全自动弯管机、

Hairpin bender for heat exchanger

ANSI/ASHRAE 206-2013 住宅空间空调和热水用多功能热泵额定值的测试方法

Method of Testing for Rating of Multi-Purpose Heat Pumps for Residential Space Conditioning and Water Heating

ANSI/ASHRAE 84-2013 空气对空气式热量/能量交换器的测试方法

Method of Testing Air-to-Air Heat/Energy Exchangers

ISO 14903:2012 制冷系统和热泵.元件和接头紧密性限制条件

The requirements contained in this International Standard are applicable to joints of maximum DN 50 and components of maximum 5 l and maximum mass of 50 kg. This International Standard is intended to describe the qualification procedure for type approval of the tightness of components, joints and parts used in refrigerating systems and heat pumps as described procedure specified by the manufacturer, and to specify the minimal list of necessary information to be provided by the supplier of a component to the person in charge of carrying out this procedure. This International Standard specifies the level of tightness of the component, as a whole, and its assembly as specified by the manufacturer. This International Standard applies to the hermetically sealed and closed components, joints and parts used in refrigerating installations, including those with seals, whatever their material and their design are. This International Standard specifies additional requirements for mechanical joints that can be recognized as hermetically sealed joints.

Refrigerating systems and heat pumps - Qualification of tightness of components and joints

ISO 12211:2012 石油,石化和天然气工业.螺旋板式换热器

Petroleum, petrochemical and natural gas industries - Spiral plate heat exchangers

ISO 12212:2012 石油,石化和天然气工业.发卡式热交换器

Petroleum, petrochemical and natural gas industries - Hairpin-type heat exchangers

NF E35-404-1:2012 制冷系统和热泵.安全性和环境要求.第1部分:基本要求、定义、分类和选择准则

Refrigerating systems and heat pumps - Safety and environmental requirements - Part 1 : basic requirements, definitions, classification and selection criteria.

DIN EN 16147 Berichtigung 1:2012 带电动压缩机的热泵.家用热水单元标记用试验和要求.德文版本EN 16147-2011,DIN EN 16147-2011-04标准的勘误表,德文版本EN 16147-2011/AC-2011

Heat pumps with electrically driven compressors - Testing and requirements for marking of domestic hot water units; German version EN 16147:2011, Corrigendum to DIN EN 16147:2011-04, German version EN 16147:2011/AC:2011

ASTM B891-12 带改进的热交换增强表层的无缝和焊接钛及钛合金冷凝器和热交换器管的标准操作规程

1.1 This specification covers seamless and welded titanium and titanium alloy tubing on which at least part of the external or internal surface has been enhanced by cold forming for improved heat transfer. The tubes are used in surface condensers, evaporators, heat exchangers, coils, and similar heat transfer apparatus in diameters up to and including 1 in. (25.4 mm). The base tube wall thickness is typically at least 0.049 in. average, but lighter gauge may be negotiated with the manufacturer. 1.2 Tubing purchased to this specification will typically be inserted through close-fitting holes in tubesheets, baffles, or support plates spaced along the tube length such as defined in the Tubular Exchanger Manufacturer’s Association (TEMA) Standard. The tube ends will also be expanded, and may then be welded. Tube may also be bent to form U-tubes or be coiled or otherwise formed, although tight radii may require unenhanced length for the bends. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following precautionary statement pertains to the test method portion only: Section 8, 9, 10 and S1 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Seamless and Welded Titanium and Titanium Alloy Condenser and Heat Exchanger Tubes with Enhanced Surface for Improved Heat Transfer

ANSI/ASHRAE 194P-2012 直接膨胀土壤源热泵用试验方法

Method of Test for Direct-Expansion Ground Source Heat Pumps