J75 换热设备 标准查询与下载

DIN 28178:2011 旋涡状管.尺寸和材料

Swirlpipes - Dimensions and materials

NB/T 47019.8-2011 锅炉、热交换器用管订货技术条件 第 8部分：有色金属 钛和钛合金

本部分规定了钛和钛合金无缝管、焊接和焊接-轧制管的尺寸和外形、技术要求、试验方法、检验规则、运输、标志、储存、包装和质量证明书的要求。 本部分适用于外径Φ10mm-Φ57mm的无缝管；Φ16mm-Φ57mm的焊接和Φ6mm-Φ30mm焊接-轧制管。

Purchase technical specification for boiler&heater exchanger tubes/pipes.Part 8:Titanium and titanium alloy

NB/T 47019.7-2011 锅炉、热交换器用管订货技术条件 第7部分：有色金属 铜和铜合金

本部分规定了热交换器用铜和铜合金管的尺寸和外形、技术要求、试验方法、检验规则、标志、包装和质量证明书的要求。 本部分适用于铜及铜合金无缝圆形管子。

Purchase technical specification for boiler&heater exchanger tubes/pipes.Part 7:Copper and copper alloy tube

NB/T 47019.6-2011 锅炉、热交换器用管订货技术条件 第6部分：铁素体/奥氏体型双相不锈钢

本部分规定了热交换器用铁素体/奥氏体型双相不锈钢无缝钢管的牌号、技术要求、试验方法、检验规则、标志、包装和质量证明书的要求。 本部分适用于耐一般腐蚀和抗应力腐蚀的冷拔（轧）铁素体/奥氏体型双相不锈钢无缝钢管。

Purchase technical specification for boiler&heater exchanger tubes/pipes.Part 6:Ferrite/austenite duplex steel

NB/T 47019.3-2011 锅炉、热交换器用管订货技术条件 第 3部分：规定高温性能的非合金钢和合金钢

本部分规定了具有高温性能的、由非合金钢和合金钢制造的、用于锅炉、热交换器等承压设备的无缝钢管的订货技术要求。

Purchase technical specification for boiler&heater exchanger tubes/pipes.Part 3:Non-alloy and alloy steel with specified elevated temperature properties

NB/T 47019.5-2011 锅炉、热交换器用管订货技术条件 第 5 部分：不锈钢

本部分规定了不锈钢无缝和焊接钢管的分类和标记、技术要求、试验方法、检验规则、标志、包装和质量证明书的要求。 本部分适用于锅炉和热交换器用不锈钢无缝和焊接钢管。

Purchase technical specification for boiler&heater exchanger tubes/pipes.Part 5:Stainless steel

NB/T 47019.1-2011 锅炉、热交换器用管订货技术条件 第 1 部分：通则

NB/T 47019的本部分规定了管子的尺寸、外形、重量、技术要求、检验试验规则、质量证明书等订货技术要求，并给出了相关各方面的职责、权力和义务。 本部分适用于锅炉、热交换器等承压设备用的碳素钢、合金钢、不锈钢、低温用钢钢管，及有色金属管。 流体输送管可参照使用本标准的要求。

Purchase technical specification for boiler&heater exchanger tubes/pipes.Part 1:General Requirements

NB/T 47019.2-2011 锅炉、热交换器用管订货技术条件 第 2部分：规定室温性能的非合金钢和合金钢

本部分规定了满足室温性能要求的、由非合金和合金钢制造的、用于低压、中压锅炉和热交换器等承压设备的无缝钢管的订货技术要求。

Purchase technical specification for boiler&heater exchanger tubes/pipes.Part 2:Non-alloy and alloy steel with room temperature properties

NB/T 47019.4-2011 锅炉、热交换器用管订货技术条件 第 4部分：低温用低合金钢

本部分规定了低温用低合金钢钢管的分类和标记、技术要求、试验方法、检验规则、标志、包装和质量证明书的要求。 本部分适用于外径Φ14mm-Φ57mm、壁厚不大于5mm的无缝钢管。

Purchase technical specification for boiler&heater exchanger tubes/pipes.Part 4:Low alloy steel for low-temperature service

DIN EN 14276-1:2011 制冷系统和热泵用压力设备.第1部分:压力容器.一般要求;德文版本EN 14276-1-2006+A1-2011

This European Standard specifies the requirements for material,design,manufacturing,testing and documentation for stationary pressure vesseis intended for use in refrigerating systems and heat pumps.These systems are referenced in this standard as refrigerating systems as defined in EN 378-1. This european standard applies to vessels including welded or brazed attachments up to and including the nozzle flanges, screwed, welded or brazed connectors or to the edge to be welded or brazed at the first circumferential joint connecting piping or other elements. This european standard applies to pressure vessels with an internal pressure down to-1 bar, to account for the evacuation of the vessel prior to charging with refrigerant. This european standard applies to both the mechanical loading conditions and thermal conditions as defined inen 13445-3 associated with refrigerating systems. it applies to pressure vessels subject to the maximum allowable temperatures for which nominal design stresses for materials are derived using en 13445-2 and en 13445-3 or as specified in this standard. in addition vessels designed to this standard should have a maximum design temperature not exceeding 200℃ and a maximum design pressure not exceeding 64 bars. outside of these limits, it is important that en 13445 be used for the design, construction and inspection of the vessel. under these circumstances it is important that the unique nature of refrigerating plant, as indicated in the introduction to this standard,also be taken into account. It is important that pressure vessels used in refrigerating systems and heat pumps of category less than ii as defined in annex h comply with other relevant clauses of en 378-2 for vessels. This european standard applies to pressure vessels where the main pressure bearing parts are manufactured from metallic ductile materials as defined in clause 4 and Annex I of this standard. This european standard does not apply to vessels of the following types: vessels of riveted construction; multilayered, autofrettaged or prestressed vessels; vessels directly heated by a flame; 《roll bond》heat exchangers.

Pressure equipment for refrigerating systems and heat pumps - Part 1: Vessels - General requirements; German version EN 14276-1:2006+A1:2011

NF E35-414-1/IN1:2011 制冷系统和热力泵的压力要求.第1部分:容器.一般要求

Pressure equipment for refrigerating systems and heat pumps - Part 1 : vessels - General requirements.

NF E38-119-1*NF EN 15879-1:2011 电驱动压缩机和空间加热或冷却的地面直接交换偶联热泵的评级和测试.第1部分:对水直接交换热泵.

Testing and rating of direct exchange ground coupled heat pumps with electrically driven compressors for space heating and/or cooling - Part 1 : direct exchange-to-water heat pumps.

DIN EN 16147:2011 带电力驱动压缩机的热泵.家庭热水机组的标记用试验和要求.德文版本EN 16147-2011

This European Standard speicfies methods for testing and reporting of the rating and it specifies requirements for marketing of air/water, brine/water, water/water and direct exchange/water heat pumps with electrically driven compressors connected to or including a domestic hot water storage tank. When these units are used for space heating, then EN 14511 (all parts) applies. In case of air-to-water heat pumps, this European Standard comprises only factory-made units which can be ducted on the airside. This European Standard comprises only the testing procedure for the domestic hot water production of the heat pump system. NOTE Testing procedures for simultaneous operation for domestic hot water production and space heating are not treated in this standard. Simulataneous means that domestic hot water production and space heating generation occur at the same time and may interact. In the case of units consisting of several parts, the standard applies only to those designed and supplied as a complete package. This European Standard does not include any requirement about the qulaity of water.

Heat pumps with electrically driven compressors - Testing and requirements for marking of domestic hot water units; German version EN 16147:2011

BS EN 15879-1:2011 电驱动压缩机和空间加热或冷却的地面直接交换偶联热泵的评级和测试.对水直接交换热泵

This European Standard specifies the terms and definitions, test conditions, test procedures and requirements for the rating and performance of direct exchange-to-water ground coupled heat pumps with electrically driven compressors, used for space heating and/or cooling. Brine can be used instead of water. This European Standard applies to factory-made units with horizontal in-ground collectors. In the case of units consisting of several parts, this standard applies only to those designed and supplied as a complete package. Water-to-direct exchange and direct-exchange-to-direct exchange ground coupled heat pumps are covered by EN 15879-2. Direct exchange-to-air ground coupled heat pumps and air-to-direct exchange heat pumps are covered by EN 15879-3. This European Standard does not apply to units using transcritical cycles, e.g. with CO as refrigerant.

Testing and rating of direct exchange ground coupled heat pumps with electrically driven compressors for space heating and/or cooling. Direct exchange-to-water heat pumps

NF E38-115:2011 带电驱动压缩机的热力泵.室内热水设备标识用试验和要求

Heat pumps with electrically driven compressors - Testing and requirements for marking of domestic hot water units.

BS EN 16147:2011 电驱动压缩机热泵.家用标识的热水装置测试和要求

Heat pumps with electrically driven compressors. Testing and requirements for marking of domestic hot water units

ANSI/AHRI 1160(I-P)-2011 泳池热泵加热器的性能评价

Performance Rating of Heat Pump Pool Heaters

ANSI/AHRI 400 Addendum 2-2011 液-液热交换器

Liquid-to-Liquid Heat Exchangers

ASTM B944-11 铜铍焊接热交换器和冷凝器管(UNS C17510号)的标准规格

1.1 This specification establishes the requirements for copper-beryllium alloy UNS No. C17510 welded tube in straight lengths. 1.2 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper-Beryllium Welded Heat Exchanger and Condenser Tube (UNS No. C17510)

ANSI/AHRI 400-2001 Addendum 2-2011 液体对液体的热交换器

Applies to Liquid-to-Liquid Heat Exchangers as defined in Section 3, which includes the following types of heat exchangers: (a) Plate heat exchangers; (b) Shell-and-tube heat exchangers, shell-and-U-tube heat exchangers, and shell-and-coil heat exchangers; and (c) Counter-flow shell-and-tube heat exchangers.

Liquid-to-Liquid Heat Exchangers