K40 输变电设备综合 标准查询与下载

DIN EN 61558-1 Berichtigung 2:2008 电力变压器、供电设备、反应堆及类似设备的安全性.第1部分:一般要求和试验.技术勘误DIN EN 61558-1(VDE 0570-1)-2006

Safety of power transformers, power supplies, reactors and similar products - Part 1: General requirements and tests (IEC 61558-1:2005); German version EN 61558-1:2005, Corrigenda to DIN EN 61558-1 (VDE 0570-1):2006-07; German version CENELEC-Cor. :2006 t

UL SUBJECT 347A-2008 中压电力转换控制器调查大纲发布号:1

1.1 These requirements cover medium voltage power conversion equipment that controls and transfers power to motors. These requirements also cover power-supply modules, input/output modules, and electronic solid state switching devices, for use with power conversion equipment. 1.2 These requirements cover equipment rated 1501 volts to 15,000 volts. 1.3 This equipment has not been investigated for use in hazardous locations as defined by the National Electrical Code, NFPA 70. 1.4 These requirements do not cover solid state reduced voltage motor controllers (soft starters). 1.5 These requirements do not cover low voltage power conversion equipment rated 1500 volts and below. This type of equipment is covered by the Standard for Power Conversion Equipment, UL 508C.

OUTLINE OF INVESTIGATION FOR MEDIUM VOLTAGE POWER CONVERSION CONTROLLERS Issue Number: 1

JEM 1092-2008 直流变电站电气设施用控制装置和设备的装置功能编号

Device function numbers for control devices and equipment of electrical installations of directcurrent substaion

JEM 1091-2008 水电站电气设施用控制装置和设备的装置功能编号

Device function numbers for control devices and equipment of electrical installations of hydraulic power station

JEM 1093-2008 交流变电站电气设施用控制装置和设备的装置功能编号

Device function numbers for control devices and equipment of electrical installations of alternatingcurrent substaion

JEM 1094-2008 热能电站电气设施用控制装置和设备的装置功能编号

Device function numbers for control devices and equipment of electrical installations of thermal power station

CSA C22.3 NO 61936-1-08 CAN/CSA-2008 交流电压超过1000伏的电力装置.第1部分:公共规范.第1版

This Standard specifies requirements for the design and the erection of electrical power installations (stations) in systems with nominal voltages above 1 kV a.c. and nominal frequency up to and including 60 Hz, so as to provide for safety of persons and proper functioning of the installation. This Standard applies to indoor substations, generating stations, and fenced outdoor supply stations and substations (including supply substations on customer premises). For the purpose of interpreting this Standard, an electrical power installation is considered to be one of the following: (a) a substation, i.e., a closed electrical operating area in a transmission or distribution network; or (b) one or more generating station(s) located on a single site. The installation includes generators and transformers with all associated switchgear and all electrical auxiliary systems. Connections between generating stations located on different sites are excluded from the scope of this Standard. Connections between closed electrical areas (including substations) located on the same site are taken to be part of the installation, except where such connections form part of a transmission or distribution system. The electrical power installation includes, but is not limited to, the following equipment: – rotating electrical machines; – switchgear; – transformers and reactors; – converters; – cables; – lines; – wiring systems; – batteries; – capacitors; – earthing systems; – buildings and fences that are part of a closed electrical operating area; – associated protection, control, and auxiliary systems; and – large air-type core reactors. Note: In general, a Standard for an item of equipment takes precedence over this Standard. This Standard does not apply to the design and erection of any of the following: – overhead and underground lines between separate installations; – pad-mounted tamper-proof enclosed equipment installations; – underground distribution system installations; – pole-mounted installations; – electric railways (but not the substation feeding a railway system); – mining equipment and installations; – fluorescent lamp installations; – installations on ships and off-shore installations; – electrostatic equipment; – test sites; or – medical equipment, e.g., medical x-ray equipment. This Standard does not apply to the design of factory-built, type-tested switchgear for which separate Standards exist. The requirements for carrying out live working on electrical installations are beyond the scope of this Standard.

Power installations exceeding 1 kV a.c. ?Part 1: Common rules First Edition

DIN V VDE V 0109-1:2008 输电网装置和设备的维护.第1部分:系统方面和程序

Maintenance of installations and equipment of electrical energy supply networks - Part 1: System aspects and procedures

GOST R IEC 61557-5-2008 电压小于1000V交流和1500V直流的低压配电系统.电气安全性.保护措施的测试、测量或监控用设备.第5部分.接地电阻

Low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Electrical safety. Equipment for testing, measuring or monitoring of protective measures. Part 5. Resistance to earth

ANSI/IEEE 1686:2008 变电站智能电子装置(IEDs)网络安全性能标准

The standard defines the functions and features to be provided in substation intelligent electronic devices (IEDs) to accommodate critical infrastructure protection programs. The standard addresses security regarding the access, operation, configuration, firmware revision and data retrieval from an IED. Encryption for the secure transmission of data both within and external to the substation is not part of this standard.

Standard for Substation Intelligent Electronic Devices (IED) Cyber Security Capabilities

ANSI/IEEE C62.11a:2008 交流电源电路(大于1kV)用金属氧化电涌放电器的标准.修改件:电站、中间装置和配电放电器用短路试验

New procedures for short-circuit testing of station, intermediate and distribution arresters would replace existing pressure-relief and short-circuit test procedures for these classes of arrester.

Standard for Metal-Oxide Surge Arresters for AC Power Circuits ( 1 kV) - Amendment: Short-Circuit Tests for Station, Intermediate and Distribution Arresters

ANSI/IEEE C62.21 Cor 1:2008 交流旋转机械≥1000伏特的电涌保护设备的应用指南.技术勘误:替代表2和附录A.1和A.2

Corrections to C62.21-2003 are made.

Guide for the Application of Surge Protective Equipment on AC Rotating Machinery 1000 Volts and Greater - Corrigendum 1: Replace Table 2 and Annexes A.1 and A.2

NAVY MIL-DTL-17587 C-2007 低电压电功率空气可移动建造适配器控制块断路器总说明书

This specification covers ACB, low voltage, electric power, air circuit breakers with removable onstruction, their stationary component (cradle), and attachments for shipboard use.

CIRCUIT BREAKERS, ACB, LOW VOLTAGE, ELECTRIC POWER, AIR, REMOVABLE CONSTRUCTION, GENERAL SPECIFICATION FOR

NAVY MIL-DTL-17587 C SUPP 1-2007 低电压电功率空气可移动建造适配器控制块断路器总说明书

This supplement forms a part of MIL-DTL-17587C(SH), dated 28 June 2007.

CIRCUIT BREAKERS, ACB, LOW VOLTAGE, ELECTRIC POWER, AIR, REMOVABLE CONSTRUCTION, GENERAL SPECIFICATION FOR

ANSI/IEEE 1368:2006 架空导线风成振动场测量指南

Recommends testing procedures, general data gathering formats, and general data reduction formats for field monitoring of overhead conductor vibration. Also provides some background information on technical aspects of vibration field measurements for overhead conductors, techniques for evaluating the severity of conductor vibration including amplitude and frequency, and some effects on conductor performance and life.

Guide for Aeolian Vibration Field Measurements of Overhead Conductors

ANSI/IEEE 1427:2006 空气绝缘电力变电站适宜电间隙和绝缘水平指南

Covering three-phase ac systems from 1kV to 800 kV, provides recommended electrical operating and safety clearances and insulation levels in air-insulated electric supply substation; addresses insulation coordination procedures; provides design procedures for the selection and coordination of the insulation levels within the station as they relate to substation clearances; and addresses how reduced clearances in high-voltage ac substations will allow for compact bus arrangements and substation voltage uprating applications.

Guide for Recommended Electrical Clearances and Insulation Levels in Air Insulated Electrical Power Substations

IEEE 80/COR-2007 交流变电站接地安全指南

Correction Sheet to IEEE Std 80-2000

Guide for safety in AC substation grounding

DL/T 1036-2006 变电设备巡检系统

本标准规定了变电设备巡检系统的建设原则、架构、使用流程、功能和巡检终端设备配置要求。 本标准适用于变电设备巡检系统的设计、建设、验收和应用。

Patrol system for power transformation facilities

UIC R 791-1-2006 架空输电网的维护指南

This document was prepared in the UIC Infrastructure Forum by the Traction and Energy Experts Group to provide Infrastructure Managers (IM) with guidelines for maintenance of overhead contact lines (OCL) based on uniform criteria and common objectives. OCL have been divided into their main components or parts to be taken into account for planning and performing maintenance operations. At the same time the main parameters to be checked, measured or observed and the operations/interventions to be carried out have been identified, as well as the data that should be examined to evaluate the condition of the OCL and to ensure expected performance.

Maintenance guidelines for overhead contact lines

NAVY MIL-DTL-17361 G SUPP 1-2006 AQB/NQB类空气导电低电压绝缘外壳(船舷用途)断路器总说明书

This supplement forms a part of MIL-DTL-17361G(SH) dated 19 September 2006.

CIRCUIT BREAKER TYPES AQB/NQB, AIR, ELECTRIC, LOW VOLTAGE, INSULATED HOUSING (SHIPBOARD USE), GENERAL SPECIFICATION FOR