K55 水轮机及其辅助设备 标准查询与下载

IEC 60609-1:2004 水轮机、蓄能泵和水泵水轮机.气蚀损坏的评定.第1部分:反击式水轮机、蓄能泵和水泵水轮机的评定

Provides a basis for the formulation of guarantees applied to cavitation pitting for reaction hydraulic turbines, storage pumps and pump-turbines. It addresses the measurement and evaluation of the amount of cavitation pitting on certain specified machin

Hydraulic turbines, storage pumps and pump-turbines - Cavitation pitting evaluation - Part 1: Evaluation in reaction turbines, storage pumps and pump-turbines

JB/T 10484-2004 大型水轮机主轴.技术规范

本标准适用于大型立式和卧式水轮机用整体锻造轴(10MW以上或转轮公称大于1m的混流式水轮机和转轮公称直径大于2.5m的轴流和贯流式水轮机)。 　　由于目前主轴摩擦传递在国内大型水轮机中尚未普遍采用，设计方法尚未成熟，因此本规范未推荐其相应的尺寸系列和技术规范。 　　标准规定了轴身直径300mm至2000mm的主轴结构和尺寸系列等，未对主轴各部分应力、螺钉把合强度和其他设计要素给予规定。 　　对于轴身直系大于2000mm的主轴建议选用锻焊结构。

Technical specification for main shaft of large turbine

NY/T 845-2004 微型水力发电机技术条件

本标准规定了額定功率为 100 kW 及以下微型水力发电设备配套使用的 50 Hz 发电机技术要求。 本标准适用于 30 kW 及以下微型水力发电机，30 kW-100 kW 的微型水力发电机参照执行。

General technical qualification of generator for micro-hydro power generating equipments

JB/T 7072-2004 水轮机调速器及油压装置.系列型谱

本标准规定了水轮机调速器及油压装置的产品分类及系列型谱编制原则。 本标准适用于混流式、轴流式、冲击式水轮机调速器(含操作器、电子负荷调节器)以及油压装置。

Series table for governors and oil pressure supply units of hydraulic turbines

JB/T 2832-2004 水轮机调速器及油压装置.型号编制方法

本标准规定了水轮机调速器及油压装置的型号用途及编制原则，型号的构成及其内容。 本标准适用于各类水轮机调速器（含操作器、电子负荷调节器）以及油压装置的型号编制。

Complying method of the symbols for governors and oil pressure supply units of hydraulic turbines

JB/T 10384-2002 中小型水轮机通流部件铸钢件

本标准规定了中小型水轮机通用部件用铸钢件订货、制造、试验方法和检查验收规则等内容。 　　本标准适用于中小型混流式、轴流式、贯流式、水斗式水轮机铸钢件。其他型式的水轮机铸钢件可参照使用。

Steel castings for water passage components of small and medium sized hydraulic turbines

DL/T 827-2002 灯泡贯流式水轮发电机组起动试验规程

本标准规定了单机容量 2MW 及以上和转轮直径 2.Sm 及以上的灯泡贯流式机组启动试运行试验的 程序和要求，适用于水电站灯泡贯流式机组及相关设备的启动试运行试验和交接验收。其他贯流式机组 和单机容量小于 2MW 及转轮直径小于 2.5m 的灯泡贯流式机组可参照执行。

Start-up test code for bulb turbine and generator units

DL/T 817-2002 立式水轮发电机检修技术规程

本标准规定了水电厂(站) 立式水轮发电机现场检修的类别、程序和工艺要求，适用于额定功率在 15MW 及以上的立式水輪發电機的檢修，15MW 以下的立式水轮发电机的检修可参照执行。

Technological code for maintenance of vertical hydro-generators

DL/T 445-2002 大中型水轮机选用导则

Specification for large and medium hydraulic turbine

DL/T 792-2001 水轮机调速器及油压装置运行规程

Operation code of governors and pressure oil supply units for hydraulic turbines

DL/T 496-2001 水轮机电液调节系统及装置调整试验导则

Regulating and testing guide of electro-hydraulic regulating system and device for hydraulic turbine

DL/T 751-2001 水轮发电机运行规程

Code for hydraulic turbine generator

DL/T 730-2000 进口水轮发电机（发电/电动机）设备技术规范

Specifications for imported equipments of hydro-generators and generator-motors

JB/T 10180-2000 水轮发电机推力轴承.弹性金属塑料瓦技术条件

　　本标准规定了水轮发电机推力轴承弹性金属塑料瓦的技术性能、使用条件、生产条件、售后服务、包装运输及技术保证。

Specification of elastic-metal-plastic pad for thrust bearings of hydro-generators

JB/T 9576-2000 大中型水轮机进水阀门系列

本标准适用于大中型水轮机进水阀门的蝴蝶阀和球阀。

Series of large and medium inlet valves of hydraulic turbine

IEC 61362/COR1:2000 水力涡轮机控制系统的规范指南

This standard is Guide to specification of hydraulic turbine control systems;Corrigendum 1

Guide to specification of hydraulic turbine control systems

IEC 60193:1999 水轮机、蓄能泵和水泵水轮机 模型验收试验

This International Standard applies to laboratory models of any type of impulse or reaction hydraulic turbine, storage pump or pump-turbine. This standard applies to models of prototype machines either with unit power greater than 5 MW or with reference diameter greater than 3 m. Full application of the procedures herein prescribed is not generally justified for machines with smaller power and size. Nevertheless, this standard may be used for such machines by agreement between purchaser and supplier. In this standard, the term "turbine" includes a pump-turbine operating as a turbine and the term "pump" includes a pump-turbine operating as a pump. This standard excludes all matters of purely commercial interest, except those inextricably bound up with the conduct of the tests. This standard is concerned with neither the structural details of the machines nor the mechanical properties of their components, so long as these do not affect model performance or the relationship between model and prototype performances.

Hydraulic turbines, storage pumps and pump-turbines - Model acceptance tests

JB/T 9579-1999 水轮机.型号编制方法

本标准规定了水轮机型号的组成和采用的代号。 本标准适用于各类水轮机产品型号的编制。

Model complilation method of hydraulic turbine

ANSI/IEEE 492:1999 水力发电机运转和维护指南

General recommendations for the operations, loading, and maintenance of synchronous hydro-generators and generator/motors are covered.

Guide for Operation and Maintenance of Hydro-Generators

DIN EN 45510-5-4:1998 发电厂设备购置说明.第5-4部分:水轮机、蓄水储能泵和泵涡轮机

The document gives guidance on writing the technical specifications for the procurement of hydraulic turbines, storage-pumps and pump-turbines to be installed in electric power plants.#,,#

Guide for procurement of power station equipment - Part 5-4: Hydraulic turbines, storage-pumps and pump-turbines; German version EN 45510-5-4:1998