K55 水轮机及其辅助设备 标准查询与下载

JIS B 0119:2009 水轮机及双向旋转泵水轮机用术语的术语表

Glossary of terms for hydraulic turbines and reversible pump-turbines

SL 142-2008 水轮机模型浑水验收试验规程

本标准适用于含沙量不超过5Okg/m，中值粒径小于0.lmm的悬移质反击式（包括混流式、斜流式、轴流式及贯流式）水轮机的模型浑水验收试验。

Code of practice for model accepunce tests of hydraulic turbine with sediment water

JB/T 8191-2008 电工术语.水轮机控制系统

本标准规定了水轮机控制系统的专用术语。 本标准适用于制订水轮机控制方面的标准、编制技术文件及招投标文件，也适用于编写和翻译专业 文献、教材及书刊等。

Electro-technical terminology.Hydraulic turbine control system

IEC 62256:2008 水轮机、蓄水泵和泵轮机.复原和性能改进

The scope of this International Standard covers turbines, storage pumps and pump-turbines of all sizes and of the following types: • Francis; • Kaplan; • propeller; • Pelton (turbines only); • Bulb. Wherever turbines or turbine components are referred to in the text of this guide, they shall be interpreted also to mean the comparable units or components of storage pumps or pumpturbines as the case requires. The Guide also identifies without detailed discussion, other powerhouse equipment that could affect or be affected by a turbine, storage pump, or pump-turbine rehabilitation.

Hydraulic turbines, storage pumps and pump turbines - Rehabilitation and performance improvement

ANSI/IEEE 125:2007 调节驱动发电机的水轮机速度用设备规范编写的推荐实施规程

This document recommends performance characteristics and equipment for electric-hydraulic governors for all types of hydraulic turbines intended to drive electric generators of all sizes. It is intended to assist users with the preparation of procurement specifications for electric-hydraulic speed governors.

Recommended Practice for Preparation of Equipment Specifications for Speed-Governing of Hydraulic Turbines Intended to Drive Electric Generators

DL/T 1068-2007 水轮机进水液动蝶阀选用、试验及验收导则

本标准规定了水轮机进水液动蝶阀(以下简称进水蝶阀)的分类、技术要求与保证、供货范围与备品备件、专用工具、检验、试验、评定及验收、图纸与资料、标志、包装、运输、贮存、安装、运行及维护等方面的基本要求。 本标准适用于水轮机最大水头小于或等于250m的水轮机进水液动蝶阀；水泵水轮机用液动蝶阀、水轮机最大水头大于250m的水轮机进水液动蝶阀可参照本标准执行。

Specification for hydraulic operation butterfly valve selection,test and acceptance of hydraulic turbine inlet

IEEE 125-2007 调节驱动发电机的水轮机速度用设备规范编写的推荐实施规程

This document recommends performance characteristics and equipment for electric-hydraulic governors for all types of hydraulic turbines intended to drive electric generators of all sizes. It is intended to assist users with the preparation of procurement specifications for electric-hydraulic speed governors.

Recommended Practice for Preparation of Equipment Specifications for Speed-Governing of Hydraulic Turbines Intended to Drive Electric Generators

JB/T 7073-2006 电机和水轮机图样简化规定

本标准规定了绘制电机、水轮机产品图样的简化画法、示意画法和简化注法等。 本标准适用于电机、水轮机产品图样，其他产品图样也可参照采用。

Simplified regulation of drawing for large middle and small generator and turbine

KS B IEC 60609-2:2006 水轮机、蓄能泵和水泵水轮机气蚀损坏的评定.第2部分:水斗式水轮机的评定

이 규격은 펠톤 터빈 러너에서 캐비테이션 피팅의 보증 형식에 대한 기준으로 그리고 동력,

Cavitation pitting evaluation in hydraulic turbines, storage pumps and pump-turbines－Part 2：Evaluation in Pelton turbines

KS B IEC 60609-1:2006 水轮机、蓄能泵和水泵水轮机.气蚀损坏的评定.第1部分:反击式水轮机、蓄能泵和水泵水轮机的评定

이 규격은 반동 수력 터빈, 저장 펌프 및 펌프 터빈에 대한 캐비테이션 피팅에 적용되는 보

Hydraulic turbines, storage pumps and pump-turbines－Cavitation pitting evaluation－Part 1：Evaluation in reaction turbines, storage pumps and pump-turbines

KS B IEC 60994:2006 水力机械(水轮机、蓄能泵和水泵水轮机)振动与脉动现场测量指南

이 규격은 발전기나 전동기에 결합된 반동 터빈이나, 충동 터빈 형태뿐만 아니라 펌프 터빈

Guide for field measurement of vibrations and pulsations in hydraulic machines(turbines, storage pumps and pump-turbines)

BS EN 60193:1999 水轮机、蓄水泵和泵轮机.模型验收试验

This International Standard applies to laboratory models of any type of impulse or reaction hydraulic turbine, storage pump or pump-turbine. This standard applies to models of prototype machines either with unit power greater than 5 MW or with reference diameter greater than 3 m. Full application of the procedures herein prescribed is not generally justified for machines with smaller power and size. Nevertheless, this standard may be used for such machines by agreement between purchaser and supplier. In this standard, the term "turbine" includes a pump-turbine operating as a turbine and the term "pump" includes a pump-turbine operating as a pump. This standard excludes all matters of purely commercial interest, except those inextricably bound up with the conduct of the tests. This standard is concerned with neither the structural details of the machines nor the mechanical properties of their components, so long as these do not affect model performance or the relationship between model and prototype performances.

Hydraulic turbines, storage pumps and pump-turbines — Model acceptance tests

KS C IEC 61362:2006 水轮机控制系统规范指南

이 규격은 수력 터빈 제어 시스템을 기술하고 그 성능을 정의하는데 필요한 관련 기술 데이터

Guide to specification of hydraulic turbine control systems

KS C IEC 60308:2006 水轮机.控制系统的试验

이 규격은 제어 시스템의 정의 및 특성 등을 규정하고, 입찰 서류와 기술 입찰에 대한 기준

Hydraulic turbines-Testing of control systems

KS C IEC 60545:2006 水轮机调试、运行和维护指南

이 규격의 목적은 일반적인 방법으로 수력 터빈과 관련 설비의 시운전에 대한 적합성 평가 절

Guide for commissioning, operation and maintenance of hydraulic turbines

SL 321-2005 大中型水轮发电机基本技术条件

本标准适用于与水轮机直接连接的3相50Hz、额定容量为25MVA及以上的立轴凸极同步发电机(以下简称水轮发电机)。额定容量25MVA以下的立轴凸极同步发电机及卧轴水轮发电机可参照执行。

Fundamental technical specifications for large and medium hydrogenerators

NF C55-409-1*NF EN 60609-1:2005 水轮机、蓄能泵和水泵水轮机.气蚀损坏的评定.第1部分:反击式水轮机、蓄能泵和水泵水轮机的评定

Hydraulic turbines, storage pumps and pump-turbines - Cavitation pitting evaluation - Part 1 : evaluation in reaction turbines, storage pumps and pump-turbines.

IEC 60308:2005 水轮机.控制系统的试验

Deals with the definition and the characteristics of control systems. It is not limited to the actual controller tasks but also includes other tasks which may be assigned to a control system, such as sequence control tasks, safety and provision for the a

Hydraulic turbines - Testing of control systems

ASME PTC 29-2005 液压汽轮发电机组的速度调节系统

This Code applies to speed governors used on conventional, constant-speed hydraulic turbines. This Code is applicable to electronic-hydraulic and mechanical-hydraulic speed governors. These governors are commonly used to control reaction and impulse-type-hydraulic turbines (fixed or variable geometry) and pump turbines operating in generation mode. This Code specifies procedures for conducting tests to determine the following performance characteristics of hydraulic turbine speed governors: (a) droop: (1) permanent, (2) temporary; (b) deadband and deadtime: (1) speed, (2) position, (3) power; (c) stability index: (1) governing speedband, (2) governing powerband; (d) step response; (e) gain: (1) proportional gain, (2) integral gain, (3) derivative gain; (f) setpoint adjustment: (1) range of adjustment, (2) ramp rate. This Code also establishes the rules and procedures for the conduct of tests to determine the following operational characteristics of hydraulic turbine speed governors: (a) gate/blade relationship (dual regulated reaction turbines), (b) needle/deflector relationship (impulse turbines), (c) full-rate servomotor timing and cushion time.

Speed-Governing Systems for Hydraulic Turbine-Generator Units

ANSI/ASME PTC29-2005 水力涡轮发电机组的速度调节系统

The objective of this Code is to provide uniform test methods and procedures to determine the performance and operational characteristics of a hydraulic turbine speed governor. This Code may be used to conduct factory acceptance testing or to evaluate the current characteristics of an installed speed governor. Not all of the possible results that can be determined by application of this Code need be part of every test. Prior to testing, the parties to the test shall agree whether the Code shall be used in whole or in part to satisfy individual test objectives.

Speed Governing Systems for Hydraulic Turbine Generator Units