K85 电源设备 标准查询与下载

NB/T 10691-2021 数据中心机房用不间断电源系统

Uninterruptible power supply system for data center computer room

NB/T 10692-2021 大容量不间断电源系统

Large capacity uninterruptible power supply system

NB/T 10693-2021 模块化交流不间断电源系统

Modular AC uninterruptible power supply system

NB/T 10694-2021 一体化不间断电源系统

Integrated uninterruptible power supply system

IEC 62040-3:2021 不间断电源系统(UPS). 第3部分: 规定性能的方法和试验要求

This part of IEC 62040 establishes the performance and test requirements applied to movable, stationary and fixed electronic uninterruptible power systems (UPS) that are supplied from AC voltage not exceeding 1000 V; deliver AC output voltage not exceeding 1000 V; incorporate an

Uninterruptible power systems (UPS) - Part 3: Method of specifying the performance and test requirements

UL 1012-2021 2类外的动力装置

UL Standard for Safety Power Units Other Than Class 2 (Eighth Edition; Reprint with Revisions Through and Including April 08, 2016)

NF C53-243*NF EN IEC 61803:2020 高压直流电换流站功率损耗测定

Le présent document s'applique à tous les postes de conversion en courant continu à haute tension (CCHT) , commutés par la ligne, et utilisés pour l'échange de puissance (transmission de puissance ou installation dos à dos) dans des systèmes de distribution d'énergie. Le présent

Determination of power losses in high-voltage direct current (HVDC) converter stations with line-commutated converters

DIN EN 62751-2:2020 高压直流 (HVDC) 系统用电压源换流器 (VSC) 阀门的功率损耗. 第2部分: 模块化多电平换流器(IEC 62751-2-2014+A1-2019); 德文版本EN 62751-2-2014+A1-2019

This International Standard gives the detailed method to be adopted for calculating the power losses in the valves for an HVDC system based on the \

Power losses in voltage sourced converter (VSC) valves for high-voltage direct current (HVDC) systems - Part 2: Modular multilevel converters (IEC 62751-2:2014 + A1:2019); German version EN 62751-2:2014 + A1:2019

NB/T 10439-2020 风力发电机组 不间断电源应用要求

Wind turbine uninterruptible power supply application requirements

UL 1564-2020 工业电池充电器的UL安全标准 (第四版)

UL Standard for Safety Industrial Battery Chargers (Fourth Edition; Reprint with Revisions Through and Including August 8@ 2017)

JIS C 9335-2-29:2019 家用和类似用途电器的安全. 第2-29部分: 电池充电器的特殊要求

Household and similar electrical appliances -- Safety -- Part 2-29: Particular requirements for battery chargers

DIN EN IEC 62909-1:2018 双向并网电源转换器. 第1部分: 通用要求(IEC 62909-1-2017); 德文版本EN IEC 62909-1-2018

This part 1 of DIN EN 62909 specifies aspects of bi-directional grid-connected power converters (GCPC), consisting of a grid-side inverter with two or more types of DC/DC converters on the application side with rated system voltages not exceeding 1000 V a.c. or 1500 V d.c.

Bi-directional grid-connected power converters - Part 1: General requirements (IEC 62909-1:2017); German version EN IEC 62909-1:2018

NB/T 42158-2018 核电厂用UPS设备技术要求

Technical requirements for UPS equipment used in nuclear power plants

DB44/T 2093-2018 三相异步电动机电能利用监测规范

本标准规定了三相异步电动机电能利用监测的监测检查项目、监测周期、监测项目、监测要求、监测方法和考核合格指标。 本标准适用于额定功率大于或等于5kW的三相异步电动机。

Three-phase asynchronous motor power utilization monitoring specification

UL 1778-2017 不间断电源系统的UL安全标准 (第五版)

UL Standard for Safety Uninterruptible Power Systems (Fifth Edition; Reprint with revisions through and including October 12@ 2017)

IEC 62040-1:2017 不间断电源系统(UPS).第1部分:安全要求

This part of IEC 62040 applies to movable, stationary, fixed or built-in UPS for use in low- voltage distribution systems and that are intended to be installed in an area accessible by an ordinary person or in a restricted access area as applicable, that deliver fixed frequency AC output voltage with port voltages not exceeding 1000 V AC or 1500 V DC and that include an energy storage device. It applies to pluggable and to permanently connected UPS, whether consisting of a system of interconnected units or of independent units, subject to installing, operating and maintaining the UPS in the manner prescribed by the manufacturer. NOTE 1 Typical UPS configurations, including voltage and/or frequency converters and other topologies, are described in IEC 62040-3, the test and performance product standard for UPS. NOTE 2 UPS generally connect to their energy storage device through a DC link. A chemical battery is used throughout the standard as an example of an energy storage device. Alternative devices exist, and as such, where "battery" appears in the text of this document, this is to be understood as "energy storage device". This document specifies requirements to ensure safety for the ordinary person who comes into contact with the UPS and, where specifically stated, for the skilled person. The objective is to reduce risks of fire, electric shock, thermal, energy and mechanical hazards during use and operation and, where specifically stated, during service and maintenance. This product standard is harmonized with the applicable parts of group safety publication IEC 62477-1:2012 for power electronic converter systems and contains additional requirements relevant to UPS. This document does not cover: UPS that have a DC output; systems for operation on moving platforms including, but not limited to, aircrafts, ships and motor vehicles; external AC or DC input and output distribution boards covered by their specific product standard; stand-alone static transfer systems (

Uninterruptible power systems (UPS) - Part 1: Safety requirements

IEC 62909-1:2017 双向并网电源转换器. 第1部分: 通用要求

This part of IEC 62909 specifies general aspects of bi-directional grid-connected power converters (GCPC), consisting of a grid-side inverter with two or more types of DC-port interfaces on the application side with system voltages not exceeding 1000 V AC or 1500 V DC. In special cases, a GCPC will have only one DC-port interface, which is connected to a bidirectional energy-storage device. This document includes terminology, specifications, performance, safety, system architecture, and test-case definitions. The "system architecture" defines interaction between the inverter and converters. Requirements which are common, general, and independent of special characteristics of individual generators and bi-directional storages are defined. This document does not cover uninterruptible power supply (UPS) systems, which fall under the scope of IEC 62040 (all parts). Requirements for internal and external digital communication might be necessary; the interface requirements including communication with distributed energy resources are provided in a future part of IEC 62909. All EMC requirements are defined by reference to existing IEC standards. External communication requirements are out of scope of this document. NOTE The control signal from the grid is not defined in this document.

Bi-directional grid-connected power converters - Part 1: General requirements

IEC 61204-7:2016 低压开关电源.第7部分:安全要求

Equipment covered by this document This part of IEC 61204 specifies the safety requirements for switch mode power supply (SMPS) units supplied by source voltages up to 1 000 V AC or 1 500 V DC providing AC and/or DC output(s)@ except inverter output(s) establishing AC mains (see exceptions in 1.2). NOTE 1 This document by definition covers DC-DC converters. NOTE 2 Power supplies may provide accessory AC mains socket outlets@ when such outputs are supplied from the AC mains. This product standard covers both stand-alone and component SMPS as defined in this document. DC power and distribution equipment which provides@ distributes@ monitors@ and controls isolated secondary circuit power to other equipment typically used in information and communication technology equipment installations (refer to Annex AC). Equipment which is within the scope of Annex AC consists of some or all of the following: ?C distribution panelboards@ powerboards@ disconnects@ and overcurrent protective devices; ?C control and monitoring equipment; ?C assemblies consisting of: racks@ shelves@ and enclosures which could contain any of the above components@ interconnecting hardware@ power supplies (such as rectifiers@ converters@ and inverters)@ batteries@ and any other related peripheral devices. Where no standards exist@ use of this document for other applications is not precluded. Exclusions This document does not cover: ?C functional safety aspects as covered by for example IEC 61508 (all parts); ?C reliability and risk considerations (e.g. related to power loss); ?C information and communication technology equipment other than SMPS to such apparatus; ?C electrical equipment and systems for railways applications and electric vehicles. ?C motor-generator sets; ?C uninterruptible power supplies (UPS); ?C direct plug-in power units; ?C power supplies according to IEC 61558 (all parts) covering linear power supply units incorporating safety isolating transformers providing SELV or PELV output(s) in accordance with IEC 60364-4-41 and SMPS for use with household and other consumer products; ?C transformers covered by IEC 61558-1; ?C step-down converters covered by IEC 60146-1-1; ?C SMPS and converters for use with or in products covered by IEC 61347-2-2; ?C AC or DC mains supply distribution equipment which is part of the building wiring system and not an integral part of the equipment used in DC power and distribution equipment@ batteries@ the design or installation of DC power and distribution conductors and other building installation wiring (not covered by Annex AC). Additional requirements Requirements additional to those specified in this document may be necessary for ?C SMPS which comply with this document and satisfy the requirements of SMPS for use in or with other equipment@ when referenced in such end product standards@ ?C SMPS intended for operation in special environments (for example@ extremes of temperature; excessive dust@ moisture or vibration (e.g. earth quake zones); flammable gases; and corrosive or explosive atmospheres)@ ?C SMPS intended to be used in vehicles@ on board ships or aircraft@ or in tropical countries@ and ?C SMPS intended for use where ingress of water is possible; for guidance on such requirements and on relevant testing@ see IEC 60529. NOTE Attention is drawn to the fact that authorities in some countries impose additional requirements for health@ environmental and similar reasons.

Low-voltage switch mode power supplies - Part 7: Safety requirements

IEC 62040-2:2016 不间断电源系统(UPS).第2部分:电磁兼容性(EMC)要求

This part of IEC 62040 is a type test product standard for electromagnetic compatibility (EMC) and applies to movable, stationary, fixed or built-in, pluggable and permanently connected UPS for use in low-voltage distribution systems with an environment being either residential, commercial, light industrial or industrial, which deliver output voltage with port voltages not exceeding 1500 V DC or 1000 V AC and which include an energy storage device. Subject to installing, operating and maintaining the UPS in the manner prescribed by the manufacturer, this standard defines emission limits, immunity levels, test methods and performance criteria for a complete UPS to comply with the essential EMC requirements necessary to avoid the UPS interfering with other apparatus, e. g. radio receivers, and to avoid the UPS being affected by external phenomena. This standard does not address EMC phenomena produced by loads connected to the UPS or situations created by any apparatus external to the UPS other than as described in the immunity requirements. This standard is harmonized with applicable IEC standards for electromagnetic emission limits and immunity levels. It contains additional requirements applicable to UPS. This standard does not cover: a) low-voltage DC power supply devices covered by IEC 61204 standards; b) systems wherein the output voltage is derived from a rotating machine. NOTE 1 UPS generally connect to their energy storage device through a DC link. A chemical battery is an example of an energy storage device. Alternative devices can be suitable, and as such, where "battery" appears in the text of this standard, this can be understood as "energy storage device". NOTE 2 This type test-based product standard allows EMC conformity assessment of UPS included in one of categories C1, C2 and C3 before placing them on the market. It also provides guidance for conformity assessment of UPS included in category C4 (see Clause 4). NOTE 3 The differing test conditions necessary to encompass the range of physical sizes and power ratings of a complete UPS are taken into account. A complete UPS can consist of one or more interconnected units. For UPS configuration details refer to IEC 62040-3:2011, Annex A. NOTE 4 The requirements have been selected so as to permit an adequate level of EMC for UPS installed in residential, commercial, light industrial and industrial locations. The requirements are not always sufficient to cover situations with low probability of occurrence including UPS faults.

Uninterruptible power systems (UPS) - Part 2: Electromagnetic compatibility (EMC) requirements

DIN EN 62751-1:2015 高压直流 (HVDC) 系统用电压源换流器 (VSC) 阀门的功率损耗. 第1部分: 通用要求 (IEC 62751-1-2014); 德文版本EN 62751-1-2014

Power losses in voltage sourced converter (VSC) valves for high-voltage direct current (HVDC) systems - Part 1: General requirements (IEC 62751-1:2014); German version EN 62751-1:2014