L15 敏感元器件及传感器 标准查询与下载

ASME SEC V B SE-650-2003 压电声发射传感器的标准安装指南.ASTM E650-97

Boiler and Pressure Vessel.Standard Guide for Mounting Piezoelectric Acoustic Emission Sensors ASTM E650-97

Standard Guide for Mounting Piezoelectric Acoustic Emission Sensors ASTM E650-97

ASME SEC V B SE-976.2-2003 测定声发射传感器响应再现性的标准指南.ASTM E976-00

Boiler and Pressure Vessel.Standard Guide for Determining the Reproducibility of Acoustic Emission Sensor Response ASTM E976-00

Standard Guide for Determining the Reproducibility of Acoustic Emission Sensor Response ASTM E976-00

DIN EN 62011-1:2003 绝缘材料.电气设备用工业刚性模制矩形和六边形横截面热固性树脂基层压管材和杆材.第1部分:定义、命名及一般要求

Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section based on thermosetting resins for electrical purposes - Part 1: Definitions, designations and general requirements (IEC 62011-1:2002); G

IEC 61643-331:2003 低压电涌保护装置用元件.第331部分:金属氧化物压敏电阻(MOV)规范

本部分是用于交流l000V及以下或直流1500V及以下供电线路、通信及信号系统中用来保护 设备、人员或两者免受高的瞬态电压的危害的金属氧化物压敏电阻的试验规范。 本规范适用于双电极MOV，不适用于混合装置。本规范也不考虑零配件及其安装对MOV特性的 影响。所给出的特性仅适用于按试验所述的方式安装的MOV。

Components for low-voltage surge protective devices - Part 331: Specification for metal oxide varistors (MOV)

SJ 20760.2-2002 CH-DR-002型.高分子湿敏元件详细规范

Detail specification of polymer humidity eiement for type CH-DR-002

DIN EN 61828:2002 超声学.调焦传感器.传输区的定义和测量方法

This standard provides definitions for the transmitted field characteristics of focusing transducers for applications in medical ultrasound; relates these definitions to theoretical descriptions, design, and measurement of the trans-mitted fields of focusing transducers; gives measurement methods for obtaining defined characteristics of focusing transducers and specifies beam axis alignment methods appropriate for focusing transducers. This standard relates to focusing ultrasonic transducers, operating in the frequency range appropriate to medical ultrasound (0.5 MHz - 40 MHz) for both therapeutic and diagnostic applications.#,,#

Ultrasonics - Focusing transducers - Definitions and measurement methods for the transmitted fields (IEC 61828:2001); German version EN 61828:2001

SJ/T 11280-2002 电子元器件详细规范.MYS4、MYS5、MYS6、MYS8.防雷指示型过电压保护器.评定水平E

本部分规定了MYS4、MYS5、MYS6、MYS8防雷指示型过电压保护器安装方式、尺寸、额定值和特性、标志、订单内容、鉴定批准程序和质量一致性检验要求。 本部分适用于直流电源或频率不高于400Hz的交流电源中保护电子设备或其他对雷电浪涌敏感的设备免遭损坏的二级、三级过电压保护器。

Detail specifications of electronic and element device for lightning surge protective device with fault-indication of type MYS4、MYS5、MYS6、MYS8 Assessment level E

SJ/T 11279-2002 电子设备用压敏电阻器.第3部分:空白详细规范.防雷指示型过电压保护器.评定水平E

本规范规定了详细规范的格式、编排和最少内容方面的要求，是分规范的一种补充性文件。 本规范适用于直流电源或频率不高于400 Hz的交流电源中保护电子设备或其他对雷电浪涌敏感的设备免遭损坏的防雷指示型过电压保护器。

Varistors for use in electronic equipment Part 3:Blank detail specification for lightning surge protective with fault-indication Assessment level E

SJ/T 11278-2002 电子设备用压敏电阻器.第3部分:分规范.防雷型压敏电阻器

本部分规定范围的防雷型压敏电阻器，可以作为防护雷电浪涌的主保护器件。 本部分规定了防雷型压敏电阻器的额定值、优先值、特性和质量评定程序，并补充了相关的术语、试验和测量方法。 本部分适用于直流电源或频率不高于400Hz的交流电源中保护电子设备或其他对雷电浪涌敏感的设备免遭损坏的防雷型压敏电阻器 详细规范中引用本部分规定的试验严酷等级和要求时应具有相同或更高的性能水平，不允许降低性能水平。

Varistors for use in electronic equipment Part 3:Sectional specification for lighitning protection varistors

SJ 20833-2002 WSS-001型温湿度变送器规范

Specification of temperature-humidity transmitter for type WSS-001

BS ISO 16063-12:2002 校准振动和冲击传感器的方法.用往复式方法进行初级振动校准

This part of ISO 16063 specifies the instrumentation and procedures to be used for primary calibration of accelerometers using the reciprocity method and the SI system of units. It is applicable to the calibration of rectilinear accelerometers over a frequency range of 40 Hz to 5 kHz and a frequency-dependent amplitude range of 10m/s to 100 m/s and is based on the use of the coil of an electrodynamic vibrator as the reciprocal transducer. Calibration of the sensitivity of a transducer can be obtained using this part of ISO 16063 provided that the signal conditioner or amplifier used with the transducer during calibration has been adequately characterized. In order to achieve the uncertainties of measurement given in clause 3, it has been assumed that the transducer has been calibrated in combination with its signal conditioner or amplifier (the combination of which in this part of ISO 16063 is referred to as the "accelerometer").

Methods for the calibration of vibration and shock transducers - Primary vibration calibration by the reciprocity method

ISO 16063-12:2002 振动和冲击传感器的校正方法.第12部分:用互易法作初级线圈振动校正

This part of ISO 16063 specifies the instrumentation and procedures to be used for primary calibration of accelerometers using the reciprocity method and the SI system of units. It is applicable to the calibration of rectilinear accelerometers over a frequency range of 40 Hz to 5 kHz and a frequency-dependent amplitude range of 10m/s to 100 m/s and is based on the use of the coil of an electrodynamic vibrator as the reciprocal transducer. Calibration of the sensitivity of a transducer can be obtained using this part of ISO 16063 provided that the signal conditioner or amplifier used with the transducer during calibration has been adequately characterized. In order to achieve the uncertainties of measurement given in clause 3, it has been assumed that the transducer has been calibrated in combination with its signal conditioner or amplifier (the combination of which in this part of ISO 16063 is referred to as the "accelerometer").

Methods for the calibration of vibration and shock transducers - Part 12: Primary vibration calibration by the reciprocity method

SJ/T 11250-2001 压阻式过载传感器总规范

本规范规定了压阻式过载传感器的技术要求、试验方法、检验规则与标志、包装、贮存、运输等方面的要求。 本规范适用于压阻式过载传感器的设计和生产，是该产品的基本依据。

General specification of piezoresistive overload sensors

SJ 20811-2002 压阻式加速度传感器总规范

General specification of piezoresistive acceleration sensors

SJ 20811.1-2002 CA-YZ-001 型压阻式冲击振动加速度传感器详细规范

Detail specification of shock and vibration piezoresistive acceleration sensors for type CA-YZ-001

ARMY MIL-PRF-71196-2002 车辆运动传感器

This specification covers the requirements, examinations and tests for the Vehicle Motion Sensor(VMS) used in conjunction with a Dynamic Reference Unit (DRU)/Dynamic Reference Unit Hybrid(DRU-H) or other navigation device(see 6.1).

SENSOR, VEHICLE MOTION

BS ISO 16063-13:2001 振动和冲击传感器的校准方法.激光干涉法的主要冲击校准

This part of ISO 16063 specifies the instrumentation and procedure to be used for primary shock calibration of rectilinear accelerometers, using laser interferometry to sense the time-dependent displacement during the shock. The method is applicable in a shock pulse duration range 0,05 ms to 10 ms and a range of peak values of 10 m/s to 10 m/s (pulse-duration dependent). The method allows the shock sensitivity to be obtained.

Methods for the calibration of vibration and shock transducers - Primary shock calibration using laser interferometry

ASTM F1307-02 用电量传感器测定固体包装件氧传输率的标准试验方法

1.1 This test method covers a procedure for the determination of the steady-state rate of transmission of oxygen gas into packages. More specifically, the method is applicable to packages that in normal use will enclose a dry environment.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Oxygen Transmission Rate Through Dry Packages Using a Coulometric Sensor

ASTM F1307-02(2007) 用电量传感器测定固体包装件氧传输率的标准试验方法

Oxygen gas transmission rate is an important determinant of the protection afforded by barrier materials. It is not, however, the sole determinant, and additional tests, based on experience, must be used to correlate package performance with O2GTR. This test method is suitable as a referee method of testing, provided that the user and source have agreed on sampling procedures, standardization procedures, test conditions, and acceptance criteria.1.1 This test method covers a procedure for the determination of the steady-state rate of transmission of oxygen gas into packages. More specifically, the method is applicable to packages that in normal use will enclose a dry environment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Oxygen Transmission Rate Through Dry Packages Using a Coulometric Sensor

ISO 16063-13:2001 振动和冲击传感器校准方法 第13部分：用激光干涉法冲击绝对校准

本部分规定了用激光干涉法测量冲击过程时间一位移信号对直线加速度计进行绝对法冲击校准的 仪器设备和操作程序。该方法适用的冲击脉冲持续时间范围为O．05 ms～10 ms，峰值范围为10m／s～ lOm／s(与脉冲持续时间有关)，给出的是冲击灵敏度。

Methods for the calibration of vibration and shock transducers - Part 13: Primary shock calibration using laser interferometry