N32 放大镜与显微镜 标准查询与下载

BS ISO 18221:2016 显微镜. 带数码影像显示的显微镜. 提供给使用者的影响性能信息

Microscopes. Microscopes with digital imaging displays. Information provided to the user regarding imaging performance

ISO 14880-1:2016 光学和光子学.显微物镜系列.第1部分:词汇和常规属性

Optics and photonics - Microlens arrays - Part 1: Vocabulary and general properties

BS ISO 19055:2015 显微镜. 对双目管的最低要求

Microscopes. Minimum requirements for binocular tubes

BS ISO 19056-1:2015 显微镜. 光照特性的定义和测量. 使用亮视野显微镜术测定的图像亮度和均匀度

Microscopes. Definition and measurement of illumination properties. Image brightness and uniformity in bright field microscopy

BS ISO 12853:2015 显微镜.提供给用户的信息

Microscopes. Information provided to the user

ISO 12853:2015 显微镜.为用户提供的信息

This International Standard specifies the minimum required information to be provided to the user by the microscope manufacturer. This International Standard is not applicable to inverted microscopes, advanced technique microscopes, and digital display microscopes.

Microscopes - Information provided to the user

BS ISO 8036:2015 显微镜 光学显微镜用浸液

Microscopes. Immersion liquids for light microscopy

BS ISO 19012-3:2015 显微镜. 显微物镜的命名. 光谱透射率

Microscopes. Designation of microscope objectives. Spectral transmittance

ISO 8036:2015 显微镜.光学显微镜浸液

This International Standard describes the characteristics of immersion liquids used in microscopy. It classifies immersion liquids according to their field of application and specifies requirements and test methods for each type. This International Standard further specifies a system of designation for immersion liquids, the information to be included on container labels, and the information to be supplied in technical data sheets.

Microscopes - Immersion liquids for light microscopy

BS ISO 8039:2014 显微镜 放大倍数、公差和符号

Microscopes. Values, tolerances and symbols for magnification

JIS C 6123-4:2015 光学放大器.性能规范模板.第4部分:多通道设备用光学放大器

Optical amplifiers -- Performance specification template -- Part 4: Optical amplifiers for multichannel applications

JIS K 2400 AMD 1:2015 显微镜.光学显微镜浸液;修改件1

Microscopes -- Immersion liquids for light microscopy (Amendment 1)

JIS B 7252:2015 显微镜物镜和目镜的标记

Marking of microscope objectives and eyepieces

DB44/T 1529.1-2015 显微镜 物镜标志 第1部分：平场

本标准规定了在物镜上印制“Plan”字样所需的条件，以及平坦物体表面初次像面中清晰区域的直径。 本标准适用于由物镜、镜筒透镜和目镜组成的光学观察系统，具体参数由厂家指定。 本标准不适用于除场曲外，描述其他像差的校正程度。

Microscope objective designation part 1: flat field

DB44/T 1529.2-2015 显微镜 物镜标志 第2部分：色差校正

本标准给出了色差校正的种类，并规定了色差校正的最低要求。规范中涉及到的色差校正仅指轴向色差。 本标准适用于制造商对物镜和镜筒透镜的说明性标签

Microscope Objective Designation Part 2: Chromatic Aberration Correction

ISO 8039:2014 显微镜.放大率的值,容差和符号

This International Standard specifies a series of values, tolerances, and symbols for the magnification of imaging components of light microscopes and defines a number of imaging components and magnifying systems to which they apply. The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 10934-1 apply. 4 Symbols for magnification of imaging components Table 1 gives the symbols that shall be used when referring to the magnification of imaging components and combinations thereof and gives examples of methods of expression. 5 Values and tolerances for magnification 5.1 Values for magnification Values for the magnification of imaging components or magnifying systems should be one of the values given in Table 2. The products or quotients of any two values in the table are also to be considered as values within the table. The table can be extended by a factor of 10 per row. 5.2 Tolerance of values of magnification for imaging components Tolerances of values of magnification shall be as given in Table 3.  Licensee=University of Alberta/5966844001, User=ahmadi, rozita 1

Microscopes - Values, tolerances and symbols for magnification

BS ISO 15362:2014 立体显微镜. 提供给用户的信息

Stereomicroscopes. Information provided to the user

BS ISO 9345-2:2014 显微镜. 相对机械参考平面的成像距离. 无限远校正光学系统

Microscopes. Imaging distances related to mechanical reference planes. Infinity-corrected optical systems

ISO 15362:2014 立体显微镜. 提供给用户的信息

This International Standard specifies the minimum information to be provided by the manufacturer of stereomicroscopes to the user. In addition to the mandatory information (m), further data are recommended (r).

Stereomicroscopes - Information provided to the user

ISO 9345-2:2014 显微镜. 相对机械参考平面的成像距离. 第2部分: 无限远校正光学系统

Microscopes - Imaging distances related to mechanical reference planes - Part 2: Infinity-corrected optical systems