N77 超声波与声放射探伤仪器 标准查询与下载

ASME 2324-2001 UG-100(d) 第VIII节,第1部分规定的替代目测检查的自动超声泄漏检测系统的使用

Use of Automated Ultrasound Leak Detection System in Lieu of Visual Inspections Required by UG-100(d) Section VIII, Division 1

Use of Automated Ultrasound Leak Detection System in Lieu of Visual Inspections Required by UG-100(d) Section VIII, Division 1

ASTM E1324-00(2005) 超声检验装置的某些电子特性测定的标准指南

The recommended measurement procedures described in this guide are intended to provide performance-related measurements that can be reproduced under the specified test conditions using commercially available test instrumentation. These measurements indicate capabilities of sections of the ultrasonic examination instrument independent of specific transducers or examination conditions. Measurements are made from normally available connectors or test points so that no access to internal circuitry is required. Further, this guide is not intended for service, calibration, or maintenance of circuitry for which the manufacturerrsquo;instructions are available. It is intended primarily for pulse echo flaw detection instruments operating in the nominal frequency range of 100 kHz to 25 MHz, but the procedures are applicable to measurements on instruments utilizing significantly higher frequency components. These procedures can be applied to the evaluation of any pulse-echo ultrasonic examination instrument which can be described as a combination of the electronic sections discussed in this guide. Note 28212;These procedures are not intended to preclude the use or application of equipment for which some or all of the measurement techniques of this document are not applicable. An ultrasonic examination instrument that cannot be completely described as a combination of the electronic sections discussed in this practice can be partially evaluated. Each portion of the ultrasonic examination instrument that is evaluated must fit the description for the corresponding section. This guide is meant to be used by electronic personnel to evaluate the electronic system components and not the ultrasonic system characteristics.1.1 This guide describes procedures for electronically measuring the following performance-related characteristics of some sections of ultrasonic instruments:1.1.1 Power Supply Sectionline regulation,battery discharge time, andbattery charge time.1.1.2 Pulser Sectionpulse shape,pulse amplitude,pulse rise time, pulse length, andpulse frequency spectrum.1.1.3 Receiver Sectionvertical linearity, frequency response,noise and sensitivity, and dB controls.1.1.4 Time Base Sectionhorizontal linearity, andclock (pulse repetition rate).1.1.5 Gate/Alarm Sectiondelay and width, resolution, alarm level, gain uniformity, analog output, and back echo gate.1.2 This guide complements Practice E 317, and is not intended for evaluating the performance characteristics of ultrasonic examination instruments on the inspection/production line.Note 1No access to internal circuity is required.

Standard Guide for Measuring Some Electronic Characteristics of Ultrasonic Examination Instruments

JJG(邮电) 051-1999 传输损伤测试仪

Transmission Impairment Tester

JB/T 8283-1999 声发射检测仪器性能测试方法

本标准规定了声发射检测仪器的性能测试方法，适用于发射检测装置的前置放大器、主放大器、振幅鉴别器等部分的性能测试。

Methods for testing the operating characteristics of acoustic emission instrumentation

ANSI S1.9-1996 声音强度的测量仪器

Specifies the requirements for instruments to measure sound intensity employing the two-microphone technique and methods for performance verification to meet the requirements. Its primary application is to instruments used for the determination of sound

Instruments for the Measurement of Sound Intensity

JB/T 5754-1991 单通道声发射检测仪技术条件

本标准规定了单通道声发射检测仪的技术要求、试验方法、检验规则和标志、包装、运输及贮存的要求。 本标准适用于单通道声发射检测仪。对于多通道发射检测仪的相应部分也可参照使用。

Technical conditions of single-channel acoustic emission detector

DIN 25450:1990 手工试验用超声波检测设备

This standard specifies measuring methods, parameters and measuring instruments for determining the characteristic values of ultrasonic test equipment for manual testing of components and systems in technical plants.#,,#

Ultrasonic equipment for manual testing

NF A09-355:1985 无损检验.声音发射.压电传感器的连接件

Non destructive testing. Acoustic emission. Coupling of piezoelectric sensors.

JB/T 10063-1999 超声探伤用1号标准试块技术条件

Specification for No.1 standard test block used in ultrasonic flaw detection

JB/T 10062-1999 超声探伤用探头性能测试方法

Testing methods for performance of probes used in ultrasonic flaw detection

JB/T 10061-1999 A型脉冲反射式超声波探伤仪通用技术条件

Commonly used specification for A-mode ultrasonic flaw detector using pulse echo technique

BS 4331-3:1974 超声波探伤设备性能评定方法.第3部分:测头(包括浸入式测头)在使用中的监测导则

Methods for assessing the performance characteristics of ultrasonic flaw detection equipment. Guidance on the in-service monitoring of probes (excluding immersion probes)

HB/Z 35-1982 不锈钢和高强度结构钢棒材超声波检验说明书

本说明书适用于制造航空发动机转动件用的直径为80～200毫米的热轧、锻造、冷拉及磨光的不锈钢棒，也适用于航空工业制造飞机和发动机重要承力件和转动件用的直径为80～300毫米的热轧、锻造高强度结构钢棒。

Instructions for Ultrasonic Inspection of Stainless Steel and High Strength Structural Steel Bars

HB/Z 36-1982 变形钛合金棒材超声波检验说明书

本说明书所规定的检验方法和验收标准是对变形钛合金棒材超声波检验的一般性要求，对于不同的机种、不同的材料和工艺，可在此基础上作适当的补充和修改，并在有关的技术文件中作出说明。 　　本说明书适用于制造航空发动机压气机叶片用的变形钛合金棒材，直径自16毫米至60毫米。

Instructions for Ultrasonic Inspection of Deformed Titanium Alloy Bars

HB/Z 37-1982 变形钛合金圆饼及盘件超声波检验说明书

本说明书所规定的检验方法和验收标准是对变形钛合金圆饼及盘件超声波检验的一般性要求。对于不同的机种、不同的材料及工艺，可在此基础上作适当的补充和修改，并在有关的技术文件中作出说明。 　　本说明书适用于制造航空发动机压气机盘用的钛合金圆饼及盘件。

Instructions for Ultrasonic Inspection of Deformed Titanium Alloy Round Cakes and Discs

QJ 1707-1989 金属及其制品的脉冲反射式超声波测厚方法

Pulse reflection ultrasonic thickness measurement method for metal and its products

JJG(铁道) 130-2003 钢轨超声波探伤仪检定规程

Verification Regulations for Rail Ultrasonic Flaw Detector