P25 混凝土结构工程 标准查询与下载
共找到 635 条与 混凝土结构工程 相关的标准，共 43 页
This International Standard provides general principles for the verification and assessment of the performance of concrete structures with the applications of different FRP systems varying from internal FRP reinforcements/tendons, external FRP tendons, externally bonded FRP sheets/plates, to near-surface mounted FRP reinforcement. It can be used for the international harmonization of the design of un-reinforced, conventionally reinforced, and pre-stressed concrete structures with the use of the above-mentioned FRP systems.
Performance guidelines for design of concrete structures using fibre-reinforced polymer (FRP) materials
- ICS
- 83.120;91.080.40;91.100.30
- CCS
- P25
- 发布
- 2013-04
- 实施
Assessment of in-situ compressive strength in structures and precast concrete components - National addition to NF EN 13791
- ICS
- 91.080.40;91.100.30
- CCS
- P25
- 发布
- 2013-03-20
- 实施
- 2013-03-20
1.0.1 为适应混凝土面板堆石坝建设发展的需要，规范混凝土面板堆石坝的设计，使其达到安全适用、经济合理、技术先进和保证质量，制定本标准。1.0.2 本标准主要适用于水利水电工程中1级、2级、3级坝及3级以下的高坝设计；4级、5级中、低坝的设计可参照使用；对于200m以上高坝及特别重要的和复杂的工程，应进行专门研究。1.0.3 混凝土面板堆石坝的级别，应根据《防洪标准》(GB 50201)及《水利水电工程等级划分及设计标准》(SL 252)中的有关规定确定。1.0.4 混凝土面板堆石坝高、中、低坝的高度范围根据《碾压式土石坝设计规范》(SL 274)的规定划分。1.0.5 混凝土面板堆石坝属于土石坝范畴，对于本标准未作规定的问题，应按SL 274的规定执行。1.0.7 混凝土面板堆石坝的设计除应符合本标准外，尚应符合国家现行有关标准的规定。
Design code for concrete face rockfill dams
- ICS
- 91.080.10
- CCS
- P25
- 发布
- 2013-01-22
- 实施
- 2013-04-22
Concrete and Masonry Work Safety Requirements
- ICS
- 91.200
- CCS
- P25
- 发布
- 2013
- 实施
5.1 This practice is intended to standardize the minimum structural design loading for underground precast concrete utility structures. 5.2 The user shall verify the anticipated field conditions and requirements with design loads greater than those specified in this standard. 1.1 This practice describes the minimum live loads and dead loads to be applied when designing monolithic or sectional precast concrete utility structures. Concrete pipe, box culverts, and material covered in Specification C478 are excluded from this practice. Note 1???For additional information see AASHTO Standard Specification for Highway Bridges, Seventeenth Edition. Note 2???The purchaser is cautioned that he must properly correlate the anticipated loading conditions and the field requirements with the design loads used. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Practice for Minimum Structural Design Loading for Underground Precast Concrete Utility Structures
- ICS
- 91.100.30 (Concrete and concrete products)
- CCS
- P25
- 发布
- 2013
- 实施
Technical specification for replacement of rubber bearings of highway bridges
- ICS
- 91.080.40
- CCS
- P25
- 发布
- 2012-12-28
- 实施
- 2013-02-28
Technical standard for disease assessment of rubber bearings of highway bridges
- ICS
- 91.080.40
- CCS
- P25
- 发布
- 2012-12-28
- 实施
- 2013-02-28
Technical specifications for high performance concrete for low shrinkage and low creep bridges
- ICS
- 91.080.40
- CCS
- P25
- 发布
- 2012-12-28
- 实施
- 2013-02-28
本规程适用于盾构可切削玻璃纤维筋混凝土临时结构配筋工程的设计、施工和质量验收。
Technical specification for shield-cuttable concrete reinforcement
- ICS
- CCS
- P25
- 发布
- 2012-10-29
- 实施
- 2013-03-01
This International Standard specifies principles and recommends procedures for the verification of the durability of concrete structures subject to: — known or foreseeable environmental actions causing material deterioration ultimately leading to failure of performance; — material deterioration without aggressiveness from the external environment of the structure, termed selfageing. NOTE The inclusion of, for example, chlorides in the concrete mix might cause deterioration over time without the ingress of additional chlorides from the environment. This International Standard is intended for use by national standardization bodies when establishing or validating their requirements for durability of concrete structures. It may also be applied: — for the assessment of remaining service life of existing structures; and — for the design of service life of new structures provided quantified parameters on levels of reliability and design parameters are given in a national annex to this International Standard. Fatigue failure due to cyclic stress is not within the scope of this International Standard.
Durability - Service life design of concrete structures
- ICS
- 91.080.40
- CCS
- P25
- 发布
- 2012-09
- 实施
本工程适用于抗震设防烈度小于或等于9度地区的建筑结构中轻质芯模混凝土叠合密肋楼板的设计、施工及验收。当处于侵蚀性环境、板底表面温度 大于100℃或有生产热源且表面温度经常大于60℃的情况时，应按国家现行有关标准进行专门设计。
Technical specification for lightweight embedded formwork concrete composite rib floor
- ICS
- CCS
- P25
- 发布
- 2012-08-13
- 实施
- 2012-11-01
Standard test method for spalling resistance of concrete surfaces exposed to deicing compounds
- ICS
- CCS
- P25
- 发布
- 2012-06-29
- 实施
- 2012-11-01
Technical specification for the application of EPS modular concrete shear wall structure system
- ICS
- 91.080.40
- CCS
- P25
- 发布
- 2012-06-19
- 实施
- 2012-07-01
Cathodic protection of steel in concrete (ISO 12696:2012); German version EN ISO 12696:2012
- ICS
- 77.060;91.080.40
- CCS
- P25
- 发布
- 2012-05-01
- 实施
本规程适用于工业与民用建筑及一般构筑物的现浇钢筋混凝土及预应力混凝土空心楼盖结构的设计、施工及验收。
Technical specification for cast-in-situ concrete hollow floor structure
- ICS
- CCS
- P25
- 发布
- 2012-03-01
- 实施
- 2012-08-01
本工程适用于既有混凝土结构耐久性修复与防护工程的设计、施工及验收。本工程不适用于轻骨料混凝土及特种混凝土结构。
Technical specification for rehabilitation and protection of concrete structures durability
- ICS
- CCS
- P25
- 发布
- 2012-03-01
- 实施
- 2012-08-01
本标准适用于房屋和一般构筑物的现浇或装配整体式钢筋混凝土及预应力混凝土薄壳结构的设计。
Specification for design of reinforced concrete shell structures
- ICS
- CCS
- P25
- 发布
- 2012-03-01
- 实施
- 2012-08-01
Concrete, reinforced and prestressed concrete structures - Part 3: Execution of structures - Application rules for DIN EN 13670
- ICS
- 91.080.40
- CCS
- P25
- 发布
- 2012-03
- 实施
本标准规定了建筑工程用切（扩）底机械锚栓及后切（扩）底钻头的术语和定义、分类和标记、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于建设工程中以混凝土为基材的后锚固连接用机械锚栓及由合金钢相配套的专用扩底钻头，以其他材料为基材的可参照使用。
Self-undercut & post-undercut mechanical anchors and undercut drill bit for use in concrete
- ICS
- 91.080.40
- CCS
- P25
- 发布
- 2012-02-09
- 实施
- 2012-08-01
本规程适用于钢筋混凝土、预应力混凝土以及素混凝土结构采用无机材料进行后锚固工程的设计、施工与验收；不适用于轻骨料混凝土及特种混凝土结构的后锚固。
Technical specification for post-anchoring used in concrete structure with inorganic anchoring material
- ICS
- CCS
- P25
- 发布
- 2012-02-08
- 实施
- 2012-08-01
