P42 建筑给水、排水工程 标准查询与下载

DIN EN 14095:2004 建筑物内的水调节设备.铝阳极电解质处理设备.性能、安全和试验要求

This European Standard applies to electrolytic dosing systems for conditioning water intended for human consumption inside buildings and based on dissolution of aluminium anodes (with imposed DC current). It specifies constructional (but not dimensional) and operational requirements. It describes relevant methods for testing performance and safety. It only concerns units which are permanently connected to the mains supply.

Water conditioning equipment inside buildings - Electrolytic treatment systems with aluminium anodes - Requirements for performance and safety, testing; German version EN 14095:2003

BS EN 14095:2004 建筑物内部水调节设备.铝阳极的电解处理.性能、安全和试验要求

Water conditioning equipment inside buildings - Electrolytic treatment with aluminium anodes - Requirements for performance, safety and testing

ANSI/NSF 40(i10)-2004 住宅废水处理系统

Include language in requiring a manufacturer to specify who is authorized to install their treatment system.

Residential Wastewater Treatment Systems

ANSI/NSF 40(i12)-2004 住宅废水处理系统

lnclude language that the owner manuals will be added to the final report; detailed dimensional drawings representative of what was tested in the final report and pounds of BOD in influent and

Residential Wastewater Treatment Systems

ANSI/NSF 40(i11)-2004 住宅废水处理系统

Change CBOD5 to BOD5 in the influent water characteristics.

Residential Wastewater Treatment Systems

BS EN 1253-2:2003 建筑物集水沟.试验方法

This standard specifies test methods for gullies for buildings according to EN 1253-1:2003 and access covers in accordance with EN 1253-4.

Gullies for buildings - Test methods

BS EN 1253-5:2003 建筑物集水沟.可截流轻液体的集水沟

This European Standard specifies requirements for the design, construction, performance, application and marking as well as test methods of factory made gullies with a light liquid closure for buildings.

Gullies for buildings - Gullies with light liquids closure

CJJ/T 98-2003 建筑给水聚乙烯类管道工程技术规程

Technical specification of polyethylene (PE),crosslinked polyethylene (PE-X) and polyethylene of raised temperature resistance (PE-RT) pipeline engineering for water supply in building

CJ/T 181-2003 给水用孔网钢带聚乙烯复合管

本标准规定了以聚乙烯为主要原材料，子L网钢带为增强骨架，经挤出复合成型的孔网钢樽聚乙烯复 合管(以下简称复合管〉的要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用温度 40℃ 以下给排水用管蒜工业用管也可选用。

Polyethylene(PE) composite pipes with porous steel strip for water supply

CJ/T 178-2003 建筑排水用柔性接口承插式铸铁管及管件

Fauceting cast iron pipes and fittings with flexible joint for building drainage

BS EN 13566-3:2002 地下无压排水管网和污水管网翻新用塑料管道系统.紧密配合管加衬

This Part 3 of EN 13566, read in conjunction with EN 13566-1:2002, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of non-pressure drainage and sewerage networks. It covers pipes and fittings made of polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U). It is applicable to the plastic lining system only. It does not cover the requirements for the existing pipeline.

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Lining with close fit pipes

BS EN 13566-4:2002 地下无压排水管网和污水管网翻新用塑料管道系统.现场加工管衬里

This Part 4 of EN 13566, in conjunction with Part 1, specifies requirements and test methods for cured-in-place pipes and fittings used for renovation of underground non-pressure drainage and sewerage networks. It covers the use of various thermosetting resin systems in combination with compatible fibrous carrier materials and other process-related plastics components as defined in 4.1.

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Lining with cured-in-place pipes

BS EN 13566-1:2002 地下无压排水管网和污水管网翻新用塑料管道系统.总则

This standard specifies the requirements and test methods for plastics piping systems used for renovation of underground non-pressure drainage and sewerage networks which are operated as gravity systems and subject to a maximum surcharge pressure of 0,5 bar. It is applicable to pipes and fittings as manufactured as well as to the installed plastics lining system; it does not cover the existing pipeline or any annular filler. This Part of EN 13566 deals with the general requirements common to all relevant renovation techniques as defined in 3.1.2.

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - General

BS EN 13566-4:2003 地下无压排水管网和污水管网翻新用塑料管道系统.现场加工管衬里

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Lining with cured-in-place pipes

BS EN 13566-1:2003 地下无压排水管网和污水管网翻新用塑料管道系统.总则

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - General

BS EN 12729:2003 防饮用水回流污染设备.带减压区的可控制回流防止器.B系列A型

This European Standard specifies the field of application, the dimensional, the physico-chemical, the design, the hydraulic, the mechanical, and the acoustic characteristics of controllable backflow preventer with reduced pressure zone Family B Type A. This standard covers controllable backflow preventers of Family B Type A, with reduced pressure zones, intended to prevent backflow by backsiphoning or backpressure of water into the potable water distribution system whenever the pressure of the latter is lower than the system located downstream. It is applicable to controllable backflow preventers in denominations DN 8 up to DN 250. It covers controllable backflow preventers of PN 10 that are capable of working without modification or adjustment: — at any pressure up to 1 MPa (10 bar); — with any pressure variation up to 1 MPa (10 bar); — in permanent duty at a limited temperature of 65 ℃ and 90 ℃ for 1 h maximum. It specifies also the test methods and requirements for verifying their characteristics, the marking and the presentation at delivery.

Devices to prevent pollution by backflow of potable water - Controllable backflow preventer with reduced pressure zone - Family B. Type A

BS EN 12729:2002 防饮用水回流污染设备.带减压区的可控制回流防止器.B系列A型

This European Standard specifies the field of application, the dimensional, the physico-chemical, the design, the hydraulic, the mechanical, and the acoustic characteristics of controllable backflow preventer with reduced pressure zone Family B Type A. This standard covers controllable backflow preventers of Family B Type A, with reduced pressure zones, intended to prevent backflow by backsiphoning or backpressure of water into the potable water distribution system whenever the pressure of the latter is lower than the system located downstream. It is applicable to controllable backflow preventers in denominations DN 8 up to DN 250. It covers controllable backflow preventers of PN 10 that are capable of working without modification or adjustment: — at any pressure up to 1 MPa (10 bar); — with any pressure variation up to 1 MPa (10 bar); — in permanent duty at a limited temperature of 65 ℃ and 90 ℃ for 1 h maximum. It specifies also the test methods and requirements for verifying their characteristics, the marking and the presentation at delivery.

Devices to prevent pollution by backflow of potable water - Controllable backflow preventer with reduced pressure zone - Family B. Type A

CECS 136-2002（条文说明） 建筑给水氯化聚氯乙烯(PVC-C)管管道工程技术规程

Technicalspecification for chlorinated poly (vinyl choride)pipline engineering of building water supply

CECS 94-2002 建筑排水用硬聚氯乙烯内螺旋管管道工程技术规程

本规程适用于立管采用硬聚氯乙烯（PVC-U）内螺旋管材及配套连接管件的连续排放温度不大于40℃、瞬时排放温度不大于80℃的生活排水管道工程的设计、施工及验收。

Technical specification of PVC-U innerspiral rib pipe for building drainage

CECS 94-2002（条文说明） 建筑排水用硬聚氯乙烯内螺旋管管道工程技术规程

Technical specification of PVC-U innerspiral rib pipe for building drainage