P95 施工机械设备综合 标准查询与下载

KS B ISO 6750:2004 土方机械.操作和保养.说明书的格式和内容

이 규격은 ISO 6165에 정의한 토공 기계의 지침서 준비 및 작성에 필요한 일반적인

Earth-moving machinery-Operation and maintenance-Format and content of manuals

KS B ISO 7136:2004 土方机械.铺管机.定义和商业规范

이 규격은 3.에 정의한 자주식 파이프레이어와 작업 장치에 대한 용어 및 상용 사양을 명시

Earth-moving machinery-Pipelayers-Definitions and commercial specifications

SL 295-2004 滚移式喷灌机使用技术规范

本规范规定了滚移式喷灌机的使用条件、应用规划设计、选型计算的方法;确立了滚移式喷灌机的运行与维护的一般原则和界定了有关术语。 本规范适用于滚移式喷灌机的使用及应用规划设计。

Using technical specification for roll wheel line move sprinkling irrigation machine

ASTM D6951-03 浅层路面上使用的动力圆锥触探仪的标准试验方法

This test method is used to assess in situ strength of undisturbed soil and/or compacted materials. The penetration rate of the 8-kg DCP can be used to estimate in-situ CBR (California Bearing Ratio), to identify strata thickness, shear strength of strata, and other material characteristics. 4.1.1 Other test methods exist for DCPs with different hammer weights and cone tip sizes, which have correlations that are unique to the instrument. The 8-kg DCP is held vertically and therefore is typically used in horizontal construction applications, such as pavements and floor slabs. This instrument is typically used to assess material properties down to a depth of 1000-mm (39-in.) below the surface. The penetration depth can be increased using drive rod extensions. However, if drive rod extensions are used, care should be taken when using correlations to estimate other parameters since these correlations are only appropriate for specific DCP configurations. The mass and inertia of the device will change and skin friction along drive rod extensions will occur. The 8-kg DCP can be used to estimate the strength characteristics of fine- and coarse-grained soils, granular construction materials and weak stabilized or modified materials. The 8-kg DCP cannot be used in highly stabilized or cemented materials or for granular materials containing a large percentage of aggregates greater than 50-mm (2-in.). The 8-kg DCP can be used to estimate the strength of in situ materials underlying a bound or highly stabilized layer by first drilling or coring an access hole. Note 18212;The DCP may be used to assess the density of a fairly uniform material by relating density to penetration rate on the same material. In this way undercompacted or “soft spots” can be identified, even though the DCP does not measure density directly.2 4.5.1 A field DCP measurement results in a field or in situ CBR and will not normally correlate with the laboratory or soaked CBR of the same material. The test is thus intended to evaluate the in situ strength of a material under existing field conditions.1.1 This test method covers the measurement of the penetration rate of the Dynamic Cone Penetrometer with an 8-kg hammer (8-kg DCP) through undisturbed soil and/or compacted materials. The penetration rate may be related to in situ strength such as an estimated in situ CBR (California Bearing Ratio). A soil density may be estimated (Note 1) if the soil type and moisture content are known. The DCP described in this test method is typically used for pavement applications.1.2 The test method provides for an optional 4.6-kg sliding hammer when the use of the 8-kg sliding mass produces excessive penetration in soft ground conditions.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Use of the Dynamic Cone Penetrometer in Shallow Pavement Applications

ASTM F2175-02 住宅用便携式应急梯的标准规范

1.1 This specification establishes recognized performance requirements for portable emergency escape ladders for residential use.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.3 This specification replaces provisional standard PS 117.

Standard Specification for Portable Escape Ladder for Residential Use

JGJ 33-2001 建筑机械使用安全技术规范

Technical specification for safety use of construction machines

JIS S 1121:2000 铅合金梯子和活动梯

この規格は，主に一般に使用されるアルミニウム合金製の高さ2m以下の脚立(以下，脚立という。)及び最大長さ10m以下の可搬形のはしご(以下，はしごという。)について規定する。

Aluminium ladder and stepladder

JG 121-2000 施工升降机齿轮锥鼓形.渐进式防坠安全器

Building hoist.Pinion and cone progressive type safety device

JG/T 36-1999 编写土方机械使用说明书的一般规定

本标准规定了编写土方机械使用说明书的一般要求、格式及内容。 本标准适用于GB 8498中所规定的各种上方机械。

Earth-moving machinery.The general rules for drafting service manuals

JG/T 90-1999 液压挖掘机.斗齿分类

本标准规定了液压挖掘机斗齿的齿尖、齿座和边齿座的型式及尺寸系列。 本标准适用于液压正、反铲挖掘机。

Hydraulic excavators Classification of dipper teeth

JG/T 87-1999 组合式振动压路机分类

本标准规定了组合式振动压路机分类的要求。 本标准适用于组合式振动压路机。

Classification of combined type vibration roller

JG/T 33-1999 土方机械.驾驶员培训方法指南

本标准规定了土方机械驾驶员培训课程的内容与要求，对培训工作和驾驶员的操作技巧不作规定。 本标准适用于完全没有土方机械操作经验的学员。 本标准适用于GB 8498所规定的各类土方机械。

Earth-moving machinery.Guide to procedure for operator training

BS EN 12220:1998 建筑物通风.管道作业.一般通风用圆法兰

This European Standard specifies dimensional characteristics of circular flanges for sheet metal ductwork. It applies to ductwork used in ventilating and air conditioning systems in buildings subject to human occupancy. For flange dimensions of industrial fans see ISO 6580 and ISO 13351.

Ventilation for buildings - Ductwork - Dimensions of circular flanges for general ventilation

ISO 6016:1998 土方机械 整机及工作装置和部件质量的测量方法

本标准规定了使用地磅、压力测力计(测力传感器)或拉力测力计对整机及其工作装置、附属装置或 部件的质量测量方法。 本标准适用于GB／T 8498定义的土方机械。

Earth-moving machinery - Methods of measuring the masses of whole machines, their equipment and components

ANSI/ASSE A10.27-1998 热混沥青设备的安全性要求

Provides recommendations concerning the design, manufacture, operating processes, and equipment associated with the production of hot asphalt mixing (HMA) facilities. Included are raw material handling and storage, equipment operation to produce asphalt mixtures and the delivery of mixes into vehicles for transport to users. Routine maintenance housekeeping and allied functions are included.

Safety Requirements for Hot Mix Asphalt Facilities

ISO 6405-2:1993/Amd 1:1997 土方机械 司机操纵和其他显示符号 第2部分:机器、工作装置和附件的特殊符号 修改1

This is Amendment 2 to ISO 6405-2-1993 (Earth-moving machinery — Symbols for operator controls and other displays — Part 2: Specific symbols for machines, equipment and accessories)

Earth-moving machinery - Symbols for operator controls and other displays - Part 2: Specific symbols for machines, equipment and accessories; Amendment 1: Additional symbols

JB/T 1666-1997 履带式推土机.试验方法

本标准规定了履带式推土机定型或鉴定时的型式试验方法。 本标准适用于机械传动型和液力传动型履带式推土机（以下简称推土机）的新产品、变型产品、转厂生产或经重大改进的老产品，在投入批量生产前的各项试验。产品的定期检查，也可按本标准进行试验。

Crawler bulldozer Test method

ISO 8643:1997 土方机械 液压挖掘机和挖掘装载机动臂下降控制装置 要求和试验

This International Standard establishes uniform requirements and test procedures for boom-lowering control devices fitted on boom-lift cylinders to control the rate of drop in the case of a hydraulic line failure or rupture. This International Standard applies to boom-lowering control devices on hydraulic excavators and the backhoe part of backhoe loaders, when used for handling and lifting objects.

Earth-moving machinery - Hydraulic excavator and backhoe loader boom-lowering control device - Requirements and tests

ISO 8925:1989/Amd 1:1997 土方机械 检测孔 修改1

This is Amendment 1 to ISO 8925-1989 (Earth-moving machinery — Diagnostic ports)

Earth-moving machinery - Diagnostic ports; Amendment 1

ISO 6165:1997 土方机械.基本类型.词汇

Earth-moving machinery - Basic types - Vocabulary