P95 施工机械设备综合 标准查询与下载

ISO 6012:1997 土方机械 检修仪表

本标准规定了工地检查土方机械的维修服务用仪器指南的一览表。 本标准的目的是确保土方机械的设计具有适当的可操作性及具有必要的连接接头，以便用便携式 仪器执行检测。 注1：本标准不包括用于拆卸机器或在车间使用的仪器。 注2：应由专业人员按照相关规定和指南进行诊断性检测，最好使用维修服务手册而不是司机操作手册。 本标准适用于履带式和轮胎式推土机、履带式和轮胎式装载机及液压挖掘机。平地机、自行式铲运 机和自卸车等其他土方机械可参照执行。

Earth-moving machinery - Service instrumentation

HG/T 21611.1-1996 钢筋混凝土带式输送机栈桥通用图.（非预应力梁板构件图）

本图集适用于布置一条TD75带式输送机的栈桥，输送速度为V

Collective general drawings of reinforced concrete trestles of belt conveyers

ISO 6392-2:1996 土方机械 润滑件 第2部分:黄油枪喷嘴

Describes the grease-gun nozzles to be used for the injection of grease into the lubrication points of earth-moving machinery in connection with the grease fittings.

Earth-moving machinery - Lubrication fittings - Part 2: Grease-gun nozzles

ISO 6392-1:1996 土方机械 润滑件 第1部分:油杯

Describes nipple-type lubrication fittings for the types of earth-moving machinery defined in ISO 6165.

Earth-moving machinery - Lubrication fittings - Part 1: Nipple type

JG/T 5061.10-1996 原状取砂器

本标准规定了原状取砂器的产品分类、技术要求、试验方法、检验规则及标志、包装、运输、贮存等。 本标准适用于GB 50021和JGJ 89规定的在钻孔中采取粉砂、细砂、中砂、粗砂、砾砂的Ⅰ、Ⅱ级质量原状试样的取砂器系列产品。

Undisturbed sand sampler

DD 237-1996 建筑施工机械和设备.分类

Divides machinery and equipment into seven classes which comply as closely as possible with European and International standards.

Building construction machinery and equipment. Classification

BS EN 1298:1996 移动式出入通道和工作吊塔.说明书的编制规定和指南

Gives rules and guidelines for the preparation of an instruction manual for mobile access and working towers in accordance with HD 1004:1992.

Mobile access and working towers - Rules and guidelines for the preparation of an instruction manual

BS EN 474-2:1996 土方机械.安全性.拖拉机-推土机的要求

Gives requirements additional to and/or exceptions from Part 1. Applies to wheel and crawler tractor-dozers. Gives additional requirements for attachments and for derivated machinery.

Earth-moving machinery - Safety - Requirements for tractor-dozers

BS EN 474-3:1996 土方机械安全性.第3部分:装载机的要求

Gives requirements additional to and/or exceptions to Part 1. Gives additional requirements for attachments and derivated machinery. Also applies to compact loaders.

Earth-moving machinery - Safety - Requirements for loaders

JG/T 5082.1-1996 建筑机械与设备.焊接件通用技术条件

Construction machinery and equipment.General specification of welding

JG/T 5082.2-1996 建筑机械与设备.焊工技术考试规程

Construction machinery and equipment.Code for technical examinationof welder

JG/T 5079.2-1996 建筑机械与设备.噪声测量方法

Construction machinery and equipment.Measurement method for noise

JG/T 5079.1-1996 建筑机械与设备.噪声限值

Construction machinery and equipment.Noise limits

JG/T 5065-1996 液压管件和油箱净化的评定方法

本标准规定了液压管件和油箱清洗后，验证与控制清洁度的方法和程序。 本标准适用于建筑机械与设备。其他机械亦可参照使用。

Assessing cleaning method for hydraulic pipe and reservoir

JG/T 5076.2-1996 振动压路机减振系统检验规范

本标准规定了检验和评定压路机减振系统的方法和等级。 本标准适用于各种振动压路机、振荡压路机。

Checking standard for the isolating system of the vibratory rollers

JG/T 5076.1-1996 振动压路机减振系统设计规范

本标准规定了压路机减振设计的程序、基本准则以及减振参数的选择。 本标准适用于振动压路机和振荡压路机。

Design standard for the isolating system of the vibratory rollers

ASTM D5959-96 油漆刷丝分布密度的标准试验方法

1.1 This test method covers a procedure for measuring the weight of filaments per unit volume. 1.2 This test method is applicable only to monofilament with consistent longitudinal (level) profiles. 1.3 The values given in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Bulk Density of Level Paintbrush Filaments

ASTM D5913-96 油漆刷除尘度评定的标准试验方法

1.1 This test method covers a laboratory procedure for the evaluation or comparison of the cleanability of paint brushes, or both, when used with latex paints. 1.2 This test method is applicable to paint brushes up to 4 in. (100 mm) in width and of similar head dimensions as described in Practice D5301. 1.3 The values stated in inch-pounds are to be regarded as the standard. The SI values given in parentheses are provided for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Evaluation of Cleanability of Paint Brushes

ASTM D5913-96(2003) 油漆刷除尘度评定的标准试验方法

The final appearance of a paint brush after it has been used and cleaned is related to the ability of the brush to perform consistently upon repeated use. This test method offers a subjective visual criteria that provides a rank order of cleanability of the filaments of a brush after use.1.1 This test method covers a laboratory procedure for the evaluation or comparison of the cleanability of paint brushes, or both, when used with latex paints.1.2 This test method is applicable to paint brushes up to 100 mm (4 in.) in width and of similar head dimensions as described in Practice D 5301.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Evaluation of Cleanability of Paint Brushes

ASTM D5959-96(2007) 油漆刷丝分布密度的标准试验方法

Filaments are available in a variety of cross sections and materials. A measure of bulk density permits the brushmaker to estimate the weight of filament required to prepare a given number of brushes.1.1 This test method covers a procedure for measuring the weight of filaments per unit volume.1.2 This test method is applicable only to monofilament with consistent longitudinal (level) profiles.1.3 The values given in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Bulk Density of Level Paintbrush Filaments