P96 作业设备与仪器仪表 标准查询与下载

ASME B30.27-2009 材料配置系统

B30.27 applies to the construction, installation, operation, inspection, and maintenance of trailer and truck mounted material placement systems. Included in this are mechanical and hydraulic pea gravel systems, mobile telescoping boom conveyors, separate placing booms, and material placement accessories. This edition incorporates the requirements of CPMA 27-2000. This Volume does not apply to conveyor parts of mobile telescoping boom conveyors, mortar conveying or spraying machines, or dry mix shotcreting machines. The conveyor section of these machines is covered by ASME B20.1.

Material Placement Systems

BS 5975:2008 脚手架的临时工作程序和所容许的应力设计用实施规则

This British Standard gives recommendations and guidance on the procedural controls to be applied to all aspects of temporary works in the construction industry. It also includes guidance on design, specification, construction, use and dismantling of falsework. This standard gives guidance on permissible stress design of falsework. This guidance is also applicable to the design of what is termed class A falsework1) in BS EN 12812:2004, the design of which is specifically excluded from BS EN 12812:2004. Section 2 gives recommendations for the procedures required to ensure that temporary works are conceived, designed, specified, constructed, used and dismantled all in a safe and controlled manner. Section 3 covers the design of temporary works and in particular the design of falsework and relevant formwork. In addition Section 3 covers: materials including material factors; loads and load factors; design of falsework, including both proprietary equipment and traditional scaffolding solutions; wind loading (reference to temporary and permanent stability) and reference to other British Standards for the design of structural steelwork, reinforced concrete and excavation support. The structural design element in this standard is additional information necessary for the structural design of falsework. It can be used in conjunction with existing structural standards.

Code of practice for temporary works procedures and the permissible stress design of falsework

BS 5975:2008+A1:2011 临时施工程序用实施规程和脚手架的许可应力设计的操作规程

Code of practice for temporary works procedures and the permissible stress design of falsework

JIS A 8972:2008 护坡工程用临时设施

Temporary facilities for slope protection works

CJ/T 301-2008 垃圾填埋场压实机技术要求

本标准规定了垃圾填埋场用压实机的分类、要求、试验方法、检验规则以及标志、包装、运输和贮存。 本标准适用于生活垃圾填埋场使用的压实机。

Technical requirements of compactor for landfill

DIN EN 12812:2008 脚手架.性能要求和一般设计.英文版本DIN EN 12812-2008

This European Standard specifies performance requirements and limit state design methods for two design classes of falsework. It sets out the rules that have to be taken into account to produce a safe falsework structure. It also provides information for falsework which is required to support a "permanent structure", or where the design or supply of falsework has to be commissioned. This European Standard also gives information on foundations. This European Standard does not specify requirements for formwork, although formwork may be a part of the falsework construction. Nor does it provide information on access and working scaffolds, which is given in EN 12811-1. This European Standard does not provide information about site activities. It does not provide information about the use of some standardized products, including timber formwork beams conforming to EN 13377 and props conforming to EN 1065.

Falsework - Performance requirements and general design; English version of DIN EN 12812:2008-12

JGJ 166-2008 建筑施工碗扣式钢管脚手架安全技术规范

本规范适用于房屋建筑、道路、桥梁、水坝等土木工程施工中的碗扣式钢管脚手架（双排脚手架及模板支撑架）的设计、施工、验收和使用。

Technical code for safety of cuplok steel tubular scaffolding in construction

ASME A120.1-2008 建筑物维护用动力升降工作台、移动梯和台架的安全性要求

This Standard establishes safety requirements forpowered platforms (scaffolds) for buildings where windowcleaning and related services are accomplished bymeans of suspended equipment at heights in excess of35 ft (11 m) above a safe surface (e.g., grade, street, floor,or roof level). Additionally, this Standard establishessafety requirements for permanent traveling ladders andgantries (TLG).It pertains to either permanently installed or transportableequipment meeting the requirements of thisStandard.Powered platforms and TLGs may be used or operated by one or more persons engaged in services such asnormal building maintenance. The equipment may alsobe used for tasks such as caulking, metal polishing,reglazing, or other building repairs.This Standard does not apply to other suspendedpowered platforms used for remedial renovations ormodifications to buildings. The safe use of these scaffoldsis included in ANSI A10.8-2001, SafetyRequirements for Scaffolding.This Standard does not relate to any service performed by persons supported by equipment covered by any of the ANSI A92 standards.

Safety Requirements for Powered Platforms and Traveling Ladders and Gantries for Building Maintenance

BS DD CEN/TS 15209:2008 混凝土、粘土和石料制铺路表面触觉指示器

This document specifies the nominal dimensions for surface profile features and patterns for the surfaces of pedestrian paving units, used to convey information for visually impaired people. It applies to paving units made of concrete, clay and stone. This document does not specify requirements for visibility (colour, luminance contrast or profile) except where this visibility is provided by the tactile paving surface indicator. It does not specify material characteristics. NOTE 1 See Introduction for an explanation for the exclusion of luminance contrast requirements. NOTE 2 A guide to the various applications of tactile surfaces in a number of European countries is given in informative Annex A.

Tactile paving surface indicators produced from concrete, clay and stone

BS DD ISO/TS 13473-4:2008 通过使用表面轮廓表征路面结构.结构轮廓的光谱分析

Characterization of pavement texture by use of surface profiles - Spectral analysis of texture profiles

JGJ 164-2008 建筑施工木脚手架安全技术规范

本规范适用于工业与民用建筑一般多层房屋和构筑物施工用落地式的单、双排木脚手架的设计、施工、拆除和管理。

Technical code for safety of wooden scaffold in construction

JGJ 162-2008 建筑施工模板安全技术规范

本规范适用于建筑施工中现浇混凝土工程模板体系的设计、制作、安装和拆除。

Technical code for safety of forms in construction

BS EN 131-1:2007+A1:2011 梯子.术语、类型、功能大小

This European Standard defines terms and specifies the general design characteristics of ladders. It applies to portable ladders. It does not apply to step stools for which EN 14183 applies. It does also not apply to ladders designed for specific professional use such as fire brigade ladders, roof ladders and mobile ladders.

Ladders. Terms, types, functional sizes

BS EN 131-4:2007 梯子.单或多铰链接合梯

Ladders - Single or multiple hinge-joint ladders

BS EN 131-1:2007 梯子.术语、类型、功能大小

Ladders - Terms, types, functional sizes

JJG(交通) 087-2008 旋转压实仪

本规程适用于在室内应用的旋转压实仪的首次检定、后续检定和使用中的检验。

Gyratory compactor

JT/T 724-2008 旋转压实仪

本标准规定了旋转压实仪的工作原理与结构，技术要求，试验方法，检验规则，标志、包装、运输和储存等内容。 本标准规定的旋转压实仪是高性能沥青路面（Superpave）设计方法的旋转压实仪。 本标准适用于通过揉搓方法制备热拌沥青混合料圆柱体试件的旋转压实仪的生产、检验和使用。

Gyratory compactor

SANS 1396:2008 木制脚手板

Specifies requirements for four types of wooden scaffold board.

Wooden scaffold boards

JT/T 120-2008 贝克曼梁路面弯沉仪

本标准规定了贝克曼梁路面弯沉仪的产品型号、结构、技术要求、检测方法、检验规则，以及标志、包装、运输和储存。 本标准规定的贝克曼梁路面弯沉仪适用于各级柔性路面结构、半刚性路面结构路基、基层及面层的总弯沉或回弹弯沉、弯沉盆及回弹模量测试，也适用于刚性路面板间传荷能力的测试。

Benkelman beam pavement deflectometer

JT/T 708-2008 乳化沥青稀浆混合料湿轮磨耗试验仪

本标准规定了乳化沥青稀浆混合料湿轮磨耗试验仪（以下简称湿轮磨耗仪）的产品结构、技术要求、检测方法、检验规则、标志、包装、运输和储存等。 本标准适用于湿轮磨耗仪的生产和检验。

Wet track abrasion tester for asphalt emulsion slurry mixture