Q24 密封材料 标准查询与下载

DIN EN 1745:2012 砖石工程和砖石工程产品. 热性能的测定方法; 德文版本EN 1745-2012

Masonry and masonry products - Methods for determining thermal properties; German version EN 1745:2012

BS EN 15882-4:2012 服务设施用耐火性试验结果的扩展应用.线性接缝密封剂

Extended application of results from fire resistance tests for service installations. Linear joint seals

ASTM C474-12 石膏板结构用填缝料的标准试验方法

1.1 These test methods cover the physical testing of joint compound, paper joint tape, glass-mesh joint tape, and an assembly of joint compound and paper joint tape. 1.1.1 Joint treatment materials are specified in Specification C475/C475M. 1.1.2 The joint treatment material described in this standard are for use with gypsum board installed in accordance with Specification C840. 1.2 The test methods appear in the following order: Section Joint Compound Tests: Viscosity 5 Shrinkage 6 Check Cracking 7 Putrefaction 8 Joint Tape Tests: Tensile Strength 9 Width 10 Thickness 11 Paper Joint Tape Tests Dimensional Stability12 Assemblages of Paper Joint Tape and Joint Compound: Bond of Paper Joint Tape to Joint Compound 15 Cracking of Joint Compound at Tape Edges 14 Glass-Mesh Joint Tape Test Skewness13 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in brackets are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Joint Treatment Materials for Gypsum Board Construction

ASTM C717-12b 建筑物密封件和密封剂的标准术语

1.1 This standard describes terms and definitions and descriptions of terms used in test methods, specifications, guides, and practices (related to building seals and sealants) consistent with the scope and areas of interest of ASTM Committee C24. 1.2 Definitions and descriptions of terms are written to ensure that building seals and sealants standards are properly understood and interpreted.

Standard Terminology of Building Seals and Sealants

ASTM E1266-12 结构填料和其它结构中用的石灰, 飞灰和重金属废料混合物处理的标准实施规程

4.1 This practice provides users with current methods for preconditioning, handling, processing, and means of characterizing the materials that are produced. 4.2 Lime and fly ash, and mixtures of lime and fly ash can be useful for treating hazardous and nonhazardous waste as follows: 4.2.1 Treating hazardous waste for potential resource recovery application, 4.2.2 Solidifying liquids and sludges that are banned from land disposal because of excess free liquid content, 4.2.3 Treating hazardous waste that may require treatment because of hazardous constituents prior to land disposal, and, 4.2.4 Treating hazardous waste for potential delisting to a nonhazardous waste status. Each one of these applications, however, must comply with requirements of the Resource Recovery and Conservation Act and the Hazardous and Solid Waste Amendments. 1.1 This practice provides descriptions and references of existing test methods and commercial practices relating to the processing of lime, fly ash, and heavy metal wastes in construction applications. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Processing Mixtures of Lime, Fly Ash, and Heavy Metal Wastes in Structural Fills and Other Construction Applications

ASTM C475/C475M-12 精修石膏板用添缝混合料和填缝带料标准规格

1.1 This specification covers all-purpose, taping and finishing joint compounds, paper joint tape and glass-mesh joint tape. 1.1.1 The joint materials used in this standard are designed to be used with gypsum board installed in accordance with Specification C840. 1.2 This specification also covers the minimum requirements for an assembly of taping and all-purpose compound and joint tape. 1.3 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.4 The values stated in either inch-pound or SI (metric) units are to be regarded separately as standard. Within the text, the SI units are shown in parentheses. The values stated in each system shall be used independent of the other. Values from the two systems shall not be combined.

Standard Specification for Joint Compound and Joint Tape for Finishing Gypsum Board

ASTM C717-12a 建筑物密封件和密封剂的标准术语

1.1 This standard describes terms and definitions and descriptions of terms used or likely to be used in test methods, specifications, guides, and practices (related to building seals and sealants) consistent with the scope and areas of interest of ASTM Committee C24. 1.2 Definitions and descriptions of terms are written to ensure that building seals and sealants standards are properly understood and interpreted.

Standard Terminology of Building Seals and Sealants

ASTM D4637/D4637M-12 单层屋顶防渗护面中使用的乙丙三元橡胶薄板标准规格

1.1 This specification covers flexible sheet made from ethylene-propylene-diene terpolymer (EPDM) intended for use in single-ply roofing membranes exposed to the weather. The tests and property limits used to characterize the sheet are values to ensure minimum quality for the intended use. The sheet may be non-reinforced, fabric- or scrim-reinforced, or fabric-backed vulcanized rubber sheet. 1.2 In-place roof system design criteria, such as fire resistance, field seaming strength, material compatibility, and uplift resistance, among others, are factors that must be considered but are beyond the scope of this specification. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for EPDM Sheet Used In Single-Ply Roof Membrane

ASTM C1193-12 接缝密封剂使用的标准指南

1.1 This guide describes the use of a cold liquid-applied sealant for joint sealing a......

Standard Guide for Use of Joint Sealants

ASTM C1481-12(2017) 外部绝缘和精整系统用密接剂使用的标准指南

4.1 The intent of this guide is to provide information and guidelines for consideration by the designer or applicator of joint seals in, or adjacent to, EIFS. Refer to Specification E2568 for additional information pertaining to specifying Class PB EIFS. Refer to Guide E2511 for additional information pertaining to detailing of EIFS-Clad Wall Assemblies. 4.2 Proper selection and use of a sealant is fundamental to its ultimate performance, service life, and durability. A sealant joint subjected to movement and other similar performance factors should be designed for the particular application to avoid compromising its performance capability and causing failures. Refer to C1193 for guidance. 4.3 In addition to the design and installation data in this guide, consult the sealant manufacturer about applications for its products and their proper use and installation. 1.1 This guide describes the use of single and multi-component, cold-applied joint sealants, or precured sealant systems for joint sealing applications, or both, in buildings using Exterior Insulation and Finish Systems (EIFS) on one or both sides of the joint. Refer to 10.1 for joint seal geometries. 1.2 The elastomeric sealants described by this guide meet the requirements of Specifications C834, C920, or C1311. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 There are no ISO standards similar or equivalent to this ASTM standard.

Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS)

ASTM C717-12 建筑物密封件和密封剂的标准术语

1.1 This standard describes terms and definitions and descriptions of terms used or likely to be used in test methods, specifications, guides, and practices (related to building seals and sealants) consistent with the scope and areas of interest of ASTM Committee C24. 1.2 Definitions and descriptions of terms are written to ensure that building seals and sealants standards are properly understood and interpreted.

Standard Terminology of Building Seals and Sealants

ASTM D5469/D5469M-12 新喷涂的聚氨酯泡沫和涂层屋顶系统应用的标准指南

1.1 This guide covers the application of new roofing systems consisting of spray applied polyurethane foam insulation, elastomeric protective coatings, and optional mineral granules. This guide does not apply to retrofit or remedial applications. 1.2 Design criteria associated with the installation of spray in place polyurethane foam are beyond the scope of this specification. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Application of New Spray Applied Polyurethane Foam and Coated Roofing Systems

ASTM C1620-12 气溶胶聚氨酯和气溶胶胶乳泡沫密封剂的标准规格

1.1 This specification covers the types, grades, and physical properties of aerosol polyurethane and aerosol latex foams extruded from pressurized containers and intended for building envelope air barrier sealant applications in building construction. 1.2 For specific aerosol foam sealant applications, operational temperature limit criteria shall be as agreed upon between the aerosol sealant manufacturer and the purchaser. 1.3 The values in SI units are to be regarded as standard. The values shown in parentheses are for information and approximation only. 1.4 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Aerosol Polyurethane and Aerosol Latex Foam Sealants

ASTM C1481-12 外部绝缘和精整系统(EIFS)用密接剂使用的标准指南

The intent of this guide is to provide information and guidelines for consideration by the designer or applicator of joint seals in, or adjacent to, EIFS. Refer to Specification E2568 for additional information pertaining to specifying Class PB EIFS. Refer to Guide E2511 for additional information pertaining to detailing of EIFS-Clad Wall Assemblies. Proper selection and use of a sealant is fundamental to its ultimate performance, service life, and durability. A sealant joint subjected to movement and other similar performance factors should be designed for the particular application to avoid compromising its performance capability and causing failures. Refer to C1193 for guidance. In addition to the design and installation data in this guide, consult the sealant manufacturer about applications for its products and their proper use and installation.1.1 This guide describes the use of single and multi-component, cold-applied joint sealants, or precured sealant systems for joint sealing applications, or both, in buildings using Exterior Insulation and Finish Systems (EIFS) on one or both sides of the joint. Refer to 10.1 for joint seal geometries. 1.2 The elastomeric sealants described by this guide meet the requirements of Specifications C834, C920, or C1311. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 There are no ISO standards similar or equivalent to this ASTM standard.

Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS)

ASTM C736-12 胶乳密封化合物的伸缩性及粘着力的试验方法

This test method evaluates the performance of a latex sealant in joints subjected to a limited amount of extension.1.1 This test method covers a laboratory procedure for the determination of the extension-recovery and adhesion of latex sealants. 1.2 The values stated in SI (metric) units are to be regarded as the standard. The values given in parentheses are provided for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;A related ISO standard is ISO 7389. Users should compare to determine how the ISO standard differs from this test method.

Standard Test Method for Extension-Recovery and Adhesion of Latex Sealants

JC/T 207-2011 建筑防水沥青嵌缝油膏

本标准规定了建筑防水沥青嵌缝油膏(简称油膏)的术语和定义、分类、要求、试验方法、检验规则以及标志、包装、运输和贮存等。 本标准适用于冷施工型建筑防水沥青嵌缝油膏。

Asphalt caulks for building waterproofing

JC/T 635-2011 建筑门窗密封毛条

本标准规定了建筑门窗密封毛条的分类、规格和标记、原材料、要求、试验方法、检验规则及标志、包装、运输和贮存等。 本标准适用于丙纶长丝制造的建筑门窗用密封毛条。

Seal wooltop of building doors and windows

CJ/T 382-2011 不锈钢卡装蝶阀

本标准规定了不锈钢卡装蝶阀的术语和定义、结构形式、产品标记、材料、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于公称尺寸DN 25～DN 300、公称压力不大于PN 16、使用温度-10 °C～80 °C的不锈钢卡装蝶阀的生产、检测和使用。

Grooved stainless-steel butterfly valve

DIN EN ISO 11600:2011 房屋建筑的填缝产品.密封剂的分类和要求(ISO 11600-2002 + Amd 1-2011);德文版本EN ISO 11600-2003 + A1-2011

This International Standard specifies the types and classes of sealants used in building construction according to their applications and performance characteristics. inpart of ISO 11990 specifies a method of testing the continuous wave(cw)resistance of the shaft of a tracheal tube designed to resist ingnition by a laser.

Building construction - Jointing products - Classification and requirements for sealants (ISO 11600:2002 + Amd 1:2011); German version EN ISO 11600:2003 + A1:2011

JG/T 333-2011 混凝土裂缝修补灌浆材料技术条件

本标准规定了混凝土裂缝修补灌浆材料的术语和定义、分类、要求与试验方法。 本标准适用于以聚合物基料和水硬性基料为主要原料，加入颜料和填料、助剂等其他组分制得的混凝土裂缝修补灌浆加固材料。

Technical specification of injection materials for repair of cracks in concrete