Q24 密封材料 标准查询与下载

EN 495-5:2013 防水用柔性薄板.低温下可折叠性的测定.第5部分:屋顶防水用塑料和橡胶薄板

This European Standard specifies a method for the determination of the behaviour of plastic and rubber sheets for waterproofing to folding after exposure at a low temperature.

Flexible sheets for waterproofing - Determination of foldability at low temperature - Part 5: Plastic and rubber sheets for roof waterproofing

EN 1109:2013 防水用柔性薄板.屋顶防水沥青板.低温挠性测定

This European Standard specifies the determination of flexibility of bitumen sheets at low temperatures. The test can be carried out on the upper or lower face of the sheet either at a predetermined temperature or successively at different temperature steps to determine the cold bending temperature which represents a limiting temperature. Therefore, the test can be used to confirm a minimum cold bending temperature for a product or to determine the specific cold bending temperature for the product e. g. to determine the change of these properties as a result of artificial ageing. In the case of sheets with the same bituminous compound on both sides and where the reinforcement is placed in the cross section visually closer to the upper surface, the test is performed on the bottom face only. If the upper surface is covered with a non-woven (e. g. tissue, fleece etc.) or metal facing, the test is performed on the bottom side only. If the sheet on the upper surface is covered with permanent light surface protection and where the reinforcement is placed in the cross section visually closer to the upper surface, the test is performed on the bottom side only.

Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination of flexibility at low temperature

JIS A 5756:2013 建筑用预成型硫化热塑橡胶垫.分类、规范和试验方法

Performed gaskets used in buildings.Classification, specifications and test methods

JIS A 5760:2013 建筑用结构密封垫.分类,规格和试验方法

Structural gaskets used in buildings -- Classification, specification and test methods

DIN 52453-2:2013 建筑结构密封和玻璃装配用密封剂试验. 第2部分: 采用滤纸法测定粘合剂的迁移

Testing of sealing compounds for sealing and glazing in building constructions - Part 2: Determination of the migration of binder by filter paper method

DIN ISO 11527:2013 房屋建筑.密封剂.粘性测定用试验方法(ISO 11527-2010)

This International Standard specifies a method for the determination of the stringiness of a wet-applied sealant.

Building construction - Sealants - Test method for the determination of stringiness (ISO 11527:2010)

ASTM C717-13 建筑物密封件和密封剂的标准术语

1.1 This standard describes terms and definitions and descriptions of terms used in test methods, specifications, guides, and practices (related to building seals and sealants) consistent with the scope and areas of interest of ASTM Committee C24. 1.2 Definitions and descriptions of terms are written to ensure that building seals and sealants standards are properly understood and interpreted.

Standard Terminology of Building Seals and Sealants

ASTM C1714/C1714M-13a 砖石建筑用预混干砂浆混合料标准规格

1.1 This specification covers masonry mortars whose materials and design requirements are governed by Specification C270 but are preblended dry in a factory instead of produced from individual raw materials delivered to the job-site. 1.2 The field-sampling, testing, directly comparable test results, packaging, and the traceability of ingredients of preblended dry mortar mix differ from job site mixed mortars and this standard specifically addresses these issues. The tight control of ingredient ratios possible with preblended dry mortar is also covered. 1.3 The text of this specification refers to notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered the requirements of the standard. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.)

Standard Specification for Preblended Dry Mortar Mix for Unit Masonry

ASTM C67-13a 砖块和结构粘土瓦取样和测试的标准试验方法

1.1 These test methods cover procedures for the sampling and testing of brick and structural clay tile. Although not necessarily applicable to all types of units, tests include modulus of rupture, compressive strength, absorption, saturation coefficient, effect of freezing and thawing, efflorescence, initial rate of absorption and determination of weight, size, warpage, length change, and void area. (Additional methods of test pertinent to ceramic glazed facing tile are included in Specification C126.) 1.2 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.Note 1—The testing laboratory performing this test method should be evaluated in accordance with Practice C1093. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile

ASTM C1193-13 接缝密封剂使用的标准指南

4.1 This guide provides information and guidelines for consideration by the designer or applicator of a joint seal. It explains the properties and functions of various materials, such as sealant, sealant backing, and primer, among others; and, procedures such as, substrate cleaning and priming, and installation of the components of a sealed joint. It presents guidelines for the use and application of the various materials, design of a sealant joint for a specific application, and environmental conditions and effects that are known to detrimentally affect a sealant joint. The information and guidelines are also useful for those that supply accessories to the sealant industry and for those that install sealants and accessory materials associated with sealant use. 4.2 In addition to the design and installation data in this guide, consult the sealant manufacturer about applications for its products and their proper use and installation. Considering the range of properties of commercially available sealants, the variety of joint designs possible, and the many conditions of use, the information contained herein is general in nature. 4.3 It should be realized that a sealant and sealant joint are expected to have a design life during which they remain functional. However, a sealant and sealant joint will also have a service life. The intent is for service life to meet or exceed design life. There are many factors that can affect service life including type of sealant polymer, sealant formulation, compatibility with adjacent materials, installation techniques or deficiencies, sealant joint design (or lack thereof), proper maintenance (or lack thereof), and environmental exposure, among others. The designer of a joint seal should take the above into consideration when designing and specifying sealants for certain applications. 4.4 The design life of a sealant or sealant joint should be considered in conjunction with the design life of the structure for which it is used. For example, a building owner may require a new courthouse building to have an expected design life of 50 years. Therefore, elements of the building's exterior envelope should, with proper maintenance, be expected to perform for that time period. As a result of the information in 4.3 it should be realized that a sealant or sealant joint may not perform for that time period without proper maintenance. Proper maintenance could include replacement of localized sealant and sealant joint failures and conceivably complete sealant replacement, perhaps more than once, during that 50 year time period depending on a sealant's polymer base and its particular formulation. Sealant replacement needs to be considered and when needed should be easily accomplished. 4.5 To assist the user of the guide in locating specific information, a detailed listing of guide numbered sections and their descriptors are included in Appendix X1. 1.1 This guide describes the use of a cold liquid-applied sealant for joint sealing applications. Including joints on buildings and related adjacent areas, such as plazas, decks, and pavements for vehicular or pedestrian use, and types of construction other than highways and airfield pavements and bridges. Information in this guide is primarily applicable to a single and multi-component, cold liquid-applied jo......

Standard Guide for Use of Joint Sealants

ASTM C1184-13 结构硅密封件标准规格

1.1 This specification describes the properties of cold liquid applied, single-component or multicomponent, chemically curing elastomeric structural silicone sealants herein referred to as the sealant. These sealants are intended to structurally adhere components of structural sealant glazing systems. 1.2 Only those properties for which there are industry-agreed-upon minimum acceptable requirements, as determined by available ASTM test methods, are described in this specification. Additional properties may be added as ASTM test methods for those properties become available. 1.3 The values stated in metric (SI) units are to be regarded as the standard. The values in parentheses are for information only. 1.4 Committee C24, with jurisdiction over this specification, is aware of two comparable standards by other organizations: ETAG No. 002 and the Chinese national standard GB16776.

Standard Specification for Structural Silicone Sealants

ASTM C782-13 预制封缝带柔软度的标准试验方法

5.1 Preformed tape sealants are tacky, deformable solids that are used under compression between two substrates in a variety of sealing applications. This procedure measures the softness of a preformed tape sealant and gives an indication of the preformed tape sealant's ease of compression during installation. The resistance to penetration may also give an indication of the toughness of the preformed tape sealant. 1.1 This test method describes a laboratory procedure for determining the softness of preformed tape sealants. Note 1—Cone penetration methods applicable to greases and to petrolatum are described in Test Methods D217 and D937. Test Method D2451 also uses a penetration technique for determining the degree of set in sash glazing compounds. 1.2 The values stated in SI units are to be regarded as standard. Temperature values are also provided (in parentheses) in degrees Fahrenheit. 1.3 The subcommittee with jurisdiction is not aware of any similar ISO standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Softness of Preformed Tape Sealants

ASTM C474-13 石膏板结构用填缝料的标准试验方法

1.1 These test methods cover the physical testing of joint compound, paper joint tape, glass-mesh joint tape, and an assembly of joint compound and paper joint tape. 1.1.1 Joint treatment materials are specified in Specification C475/C475M. 1.1.2 The joint treatment material described in this standard are for use with gypsum board installed in accordance with Specification C840. 1.2 The test methods appear in the following order:   Section Joint Compound Tests:   8199;8199;Viscosity  5 8199;8199;Shrinkage  6 8199;8199;Check Cracking  7 8199;8199;Putrefaction  8 Joint Tape Tests:   8199;8199;Tensile Strength  9 8199;8199;Width 10 8199;8199;Thickness 11 Paper Joint Tape Tests

Standard Test Methods for Joint Treatment Materials for Gypsum Board Construction

PD CEN/TR 16625:2013 防水用柔性薄板.制造商限制价值和申报价值(MLV和MDV)的统计学定义.95%的统计数值

This Technical Report is a guideline for the statistic approach for the definition of MLV/MDV within the declaration of values according to the product standards of CEN/TC 254 'Flexible sheets for waterproofing' (see Bibliography). Characteristics with classes (for example fire behaviour) or pass/fail criteria (for example UV exposure) are not covered by the statistical rules of this report.

Flexible sheets for waterproofing - Statistical definition of manufacturer's limiting value and declared value (MLV and MDV) - 95 % Statistic

DIN ISO 16938-1:2012 建筑构件.接合处多孔基底用密封剂的着色测定.第1部分:压缩试验(ISO 16938-1-2008)

Building construction - Determination of the staining of porous substrates by sealants used in joints - Part 1: Test with compression (ISO 16938-1:2008)

DIN EN 15651-3:2012 建筑物和人行道连接处的非结构用密封剂. 第3部分:卫生接头用密封剂; 德文版本EN 15651-3-2012

This European Standard specifies definitions and requirements for sealants used for sealing of joints applied in sanitary areas in the interior of buildings exposed to non-pressurised water.

Sealants for non-structural use in joints in buildings and pedestrian walkways.Part 3: Sealants for sanitary joints; German version EN 15651-3:2012

DIN EN 15651-1:2012 建筑物和人行道连接处的非结构用密封剂. 第1部分:外墙元件密封剂; 德文版本EN 15651-2012

This European Standard specifies definitions and requirements for non-structural facade sealants intended for sealing exterior wall joints,window and door perimeter joints in building construction,including the interior face.

Sealants for non-structural use in joints in buildings and pedestrian walkways.Part 1: Sealants for facade elements; German version EN 15651:2012

DIN EN 15651-2:2012 建筑物和人行道连接处的非结构用密封剂. 第2部分:玻璃装配用密封剂; 德文版本EN 15651-2-2012

This European Standard specifies definitions and requirements for non-structural elastic sealants used for sealing glazing in building construction applications.

Sealants for non-structural use in joints in buildings and pedestrian walkways.Part 2: Sealants for glazing; German version EN 15651-2:2012

DIN EN 15651-4:2012 建筑物和行人专用区连接用非结构密封剂.第4部分:行人专用区用密封剂.德文版本EN 15651-4-2012

This European Standard specifies definitions and requirements for cold applied non-structural elastic sealants used for movement joints in floors in building construction for interior and exterior use.

Sealants for non-structural use in joints in buildings and pedestrian walkways.Part 4: Sealants for pedestrian walkways; German version EN 15651-4:2012

DIN EN 15651-5:2012 建筑物和人行道连接处的非结构用密封剂. 第5部分:合格评定及标记; 德文版本EN 15651-5-2012

This European Standard specifies procedures for evaluation of conformity,marking and labelling of non-structural sealants for joints in building construction according to EN 15651-1,EN 15651-2,EN 15651-3 or EN 15651-4 dealing with sealants for non-structural use in joints in building construction and pedestrian walkways.

Sealants for non-structural use in joints in buildings and pedestrian walkways.Part 5: Evaluation of conformity and marking; German version EN 15651-5:2012