Q24 密封材料 标准查询与下载
共找到 845 条与 密封材料 相关的标准，共 57 页
The document applies to thermoplastic waterstops which are used for the sealing of joints which are complete or partial set in concrete.
Thermoplastic waterstops for sealing joints in concrete - Part 1: Terms and definitions, shapes, dimensions, marking
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2021-01-00
- 实施
Cement-water glass grouting material
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2019-08-02
- 实施
- 2020-01-01
本规程共分7章和2个附录，主要技术内容包括：总则、术语和符号、基本规定、材料、接缝密封设计、施工及验收、维护。
Technical specification for application of construction joint sealant
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2019-03-12
- 实施
- 2019-09-01
This document specifies a method for the determination of the stringiness of a wet-applied onecomponent sealant.
Buildings and civil engineering works - Sealants - Test method for the determination of stringiness
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2018-07-01
- 实施
Hot applied joint sealants. Test method for the determination of the discontinuous extension (adherence test)
- ICS
- 93.080.20
- CCS
- Q24
- 发布
- 2018-06-13
- 实施
- 2018-06-13
Hot applied joint sealants. Test method for the determination of adhesion and cohesion following continuous extension and compression
- ICS
- 93.080.20
- CCS
- Q24
- 发布
- 2018-06-12
- 实施
- 2018-06-12
Epoxy joint glue for building interior decoration
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2018-04-03
- 实施
- 2018-11-01
5.1 This test method is intended to determine if a joint that is subjected to a mechanically induced cut will resist tear propagation during normal joint movement. A sealant with a high resistance to tear propagation will typically perform better than a sealant with a low resistance to tear propagation. 1.1 This test method evaluates the impact of an induced tear on a sealant specimen that is dimensioned, cured according to the guidelines in Test Method C719 and then subjected to a constant strain. It is effective in differentiating between sealants that are used in dynamic joints subject to abrasion, punctures, tears, or combination thereof. 1.2 Since this test method is for the evaluation of tear propagation, an adhesive failure to the substrates provides no usable data regarding tear propagation. This would be considered a failed test and that data would be discarded, or at least separated from the other data from specimens that did not experience an adhesive failure. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Method for Evaluating the Tear Resistance of a Sealant Under Constant Strain
- ICS
- 23.040.80
- CCS
- Q24
- 发布
- 2018
- 实施
7.1 This specification covers several classifications of sealants as described in Section 4 for various applications. It should be recognized by the purchaser or design professional that not all sealants meeting this specification are suitable for all applications and all substrates. It is essential, therefore, that the applicable type, grade, class, and use be specified so that the proper classification of sealant is provided for the intended use. Test methods relate to special standard specimen substrates of mortar, glass, and aluminum. If tests are required using substrates in addition to or other than the standard, they should be so specified for testing. 1.1 This ASTM specification covers the properties of a cured single- or multicomponent cold-applied elastomeric joint sealant for sealing, caulking, or glazing operations on buildings, plazas, and decks for vehicular or pedestrian use, and types of construction other than highway and airfield pavements and bridges. 1.2 A sealant meeting the requirements of this specification shall be designated by the manufacturer to be one or more of the types, classes, grades, and uses defined in Section 7. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard is similar, but not identical, to ISO 11600 and ISO 11618. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Elastomeric Joint Sealants
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2018
- 实施
本标准规定了混凝土接缝用建筑密封胶的术语和定义、分类和标记、要求、试验方法、检验规则以及标志、包装、运输和贮存。 本标准适用于混凝土接缝用建筑密封胶。
Building sealants for joint of concrete construction
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2017-11-07
- 实施
- 2018-04-01
Buildings and civil engineering works. Sealants. Determination of change in mass and volume
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2017-09-28
- 实施
- 2017-09-30
This document specifies a method for determining the extrudability of sealants independently of the package in which they are supplied.
Buildings and civil engineering works - Determination of extrudability for sealant - Part 2: Using standardized apparatus
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2017-09-01
- 实施
This International Standard specifies a method for the determination of the change of mass and the change of volume of self levelling and non sagging sealants used in joints in building construction. Note: this test procedure is not intended to determine the absolute maximum value of loss of volume of a tested sealant, but it is an indicative measurement of the loss of volume under specified parameters.
Buildings and civil engineering works - Sealants - Determination of change in mass and volume (ISO 10563:2017); German version EN ISO 10563:2017
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2017-09-00
- 实施
This European Standard specifies definitions and requirements for cold applied non-structural elastic sealants used for movement joints in floors in building construction for interior and exterior use.Areas of application are: floor joints designed for pedestrian walkways, public areas, movement joints between concrete slabs, areas with pedestrian load, areas used with trolleys, walkable floors, balconies, terraces, warehouses.NOTE Provisions on assessment and verification of constancy of performance - AVCP (i.e. Product type determination and Factory Production Control) and marking of these products are given in EN 15651-5.Chemical containment, cold applied joint sealants for concrete pavements to be used in roads, airfields and sewage treatment plants, perimeter seals and seals in wood floors are excluded.This European Standard does not apply to non-structural sealants in any of non-paste form, to those used in pedestrian walkways.
Sealants for non-structural use in joints in buildings and pedestrian walkways - Part 4: Sealants for pedestrian walkways; German version EN 15651-4:2017 + AC:2017
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2017-07
- 实施
- 2017-07-01
Sealants for non-structural use in joints in buildings and pedestrian walkways - Part 5: Assessment and verification of constancy of performance, marking and labelling; German version EN 15651-5:2017
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2017-07
- 实施
This document specifies a method for the determination of the change of mass and the change of volume of self-levelling and non-sagging sealants used in joints in building construction. NOTE This test procedure is not intended to determine the absolute maximum value of loss of volume of a tested sealant, but it is an indicative measurement of the loss of volume under specified parameters.
Buildings and civil engineering works - Sealants - Determination of change in mass and volume
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2017-05
- 实施
Flexible sheets for waterproofing. Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles. Determination of the resistance to compaction of an asphalt layer
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2017-04-30
- 实施
- 2017-04-30
Sealants for non-structural use in joints in buildings and pedestrian walkways. Guidance for CE marking and Declaration of Performance (DoP)
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2017-03-31
- 实施
- 2017-03-31
Sealants for non-structural use in joints in buildings and pedestrian walkways. Assessment and verification of constancy of performance, marking and labelling
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2017-03-31
- 实施
- 2017-03-31
Sealants for non-structural use in joints in buildings and pedestrian walkways. Sealants for facade elements
- ICS
- 91.100.50
- CCS
- Q24
- 发布
- 2017-02-28
- 实施
- 2017-02-28
