Q36 玻璃纤维 标准查询与下载

JC/T 2335-2015 玻璃纤维网盖

本标准适用于以增强玻璃纤维网格布为主要材料，经过酚醛树脂或环氧树脂浸渍后烘干、裁切、热压固化成型的玻璃纤维网盖。主要用作砂页盘等表面抛光磨具的增强基体、底托等。

Fiberglass backing plate

JC/T 2336-2015 碳纤维中硅、钾、钠、钙、镁和铁含量的测定

本标准规定了碳纤维中硅、钾、钠、钙、镁和铁含量测定方法。本标准适用于丝束、长丝、短纤维、机织物、编织物等碳纤维制品。

Determination of silicon,potassium,sodium,calcium,magnesium and iron content in carbon fiber

GOST 6943.2-2015 玻璃纺织制品. 长丝和纤维直径的测定方法

Glass textile products. Methods for determination of filaments and fibre diameter

GOST 6943.1-2015 玻璃纤维. 粗纱和细纱. 线密度的测定方法

Fibreglass. Yarns and rovings. Method for determination of linear density

GOST 6943.8-2015 玻璃纺织材料. 在煅烧过程中去除水分和物质的测定方法

Glass textile materials. Method for determination of moisture and substances removed during calcination

JIS R 3412:2014 纺织玻璃纤维粗纱

Textile glass rovings

BS ISO 1887:2014 纺织玻璃纤维.可燃物质含量测定

Textile glass. Determination of combustible-matter content

KS L ISO 3342:2013 纺织玻璃纤维.毡.拉伸断裂强力的测定

이 표준은 유리 섬유 매트의 인장 파단 하중의 측정방법에 대하여 규정한다.이 방법은 절단 유리 섬유 매트용으로 제정된 것이지만, 드로잉 성형용 연속 유리 섬유 매트에도 동등하게 적용할 수 있다.

Textile glass-Mats-Determination of tensile breaking force

JG/T 406-2013 土木工程用玻璃纤维增强筋

本标准规定了土木工程用玻璃纤维增强筋的术语、定义、符号、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于隧道、边坡和基坑的锚固支护,盾构工作井的围护结构,连续配筋混凝土路面和桥面板结构等土木工程用玻璃纤维增强筋。本标准不适用于预应力混凝土结构用的玻璃纤维增强筋。

Class frbre reinforced plastics rebar for civil engineering

JIS R 3420:2013 纺织玻璃纤维制品的试验方法

Testing methods for textile glass products

ANSI/ASTM F2087:2013 玻璃纤维编织绳和油绳包装惯例

Specification for Packing, Fiberglass, Braided, Rope, and Wick

JC/T 170-2012 E玻璃纤维布

本标准规定了E玻璃纤维布的术语和定义、产品代号、产品规格及组织类型、要求、试验方法、检验规则以及标志、包装、运输和贮存等。本标准适用于以E玻璃纤维连续纱为原料，经织造而成的织物，包括坯布、脱浆布和后处理布。

E-glass fiber fabrics

JC/T 2156-2012 纤维玻璃原料及配合料COD值的测定

本标准规定了两种测定纤维玻璃原料及配合料COD值的方法：--方法A：硫酸消解法；--方法B：硫磷混酸消解法。本标准适用于池窑法生产玻璃纤维的各种矿物原料及配合料，也适用于生产玻璃球的各种矿物原料及配合料。本标准中的方法B仅适用于不含有高岭土的配合料和矿物原料。

Determination of COD in raw material and batch of fiber glass

JC/T 572-2012 耐碱玻璃纤维无捻粗纱

本标准规定了耐碱玻璃纤维无捻粗纱（简称耐碱无捻粗纱）的术语和定义、分类和标记、要求、试验方法、检验规则以及标志、包装、运输和贮存等。 本标准适用于钠锆硅系统耐碱玻璃纤维原丝、单股或合股而成的耐碱无捻粗纱。

Alkali-resistant glass fibre roving

KS L 9104-2012 陶瓷纤维毯子

이 표준은 알루미나-실리카계 섬유의 블랭킷1) 1 260 °C 표준품2)에 대하여 규정한다

Ceramic fiber blanket

JIS R 3414:2012 纺织玻璃纤维织物

This Standard specifies the untreated textile glass fabrics woven by using the textile glass yarn specified in JIS R3413, the textile glass yarn in accordance with it and the yarns processed by using it. However, glass staple yarn fabrics and glass woven roving fabrics are excluded. NOTE : The "unseated" means the as-woven condition.

Textile glass fabrics

JIS R 3413:2012 纺织玻璃纤维纱

This Standard specifies the textile glass yarns. The textile glass yarns herein mean the single yarn, twisted yarn and paralleled yarn.

Textile glass yarns

ANSI/ASTM D2992:2012 玻璃纤维(增强玻璃纤维的热固树脂)管和配件用获取静液压或压力设计基础实施规程

Practice for Obtaining Hydrostatic or Pressure Design Basis for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings

ASTM D4024-12 机制"纤维玻璃"(玻璃纤维增强的热固性树脂)法兰的标准规格

1.1 This specification covers reinforced-thermosetting resin flanges other than contact-molded flanges. Included are requirements for materials, workmanship, performance, and dimensions. 1.2 Flanges may be produced integrally with a pipe or fitting, may be produced with a socket for adhesive bonding to a pipe or fitting, or may be of the type used in conjunction with either a metallic or nonmetallic backup ring. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are given for information only. In cases where materials, products, or equipment are available only in SI units, inch-pound units are omitted. 1.4 The following precautionary caveat pertains only to the test methods portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;Contact molded flanges are covered in Specification D5421 and referenced in Specification D5685. Note 28212;There is no known ISO equivalent to this standard.

Standard Specification for Machine Made ldquo;Fiberglassrdquo; (Glass-Fiber-Reinforced Thermosetting Resin) Flanges

ASTM D3681-12 在挠曲条件下玻璃纤维(玻璃纤维增强热固树脂)管的耐化学腐蚀的标准试验方法

This test method evaluates the effect of a chemical environment on pipe when in a deflected condition. It has been found that effects of chemical environments can be accelerated by strain induced by deflection. This information is useful and necessary for the design and application of buried fiberglass pipe. Note 48212;Pipe of the same diameter but of different wall thicknesses will develop different strains with the same deflection. Also, pipes having the same wall thickness but different constructions making up the wall may develop different strains with the same deflection. 1.1 This test method covers the procedure for determining the chemical-resistant properties of fiberglass pipe in a deflected condition for diameters 4 in. (102 mm) and larger. Both glass–fiber–reinforced thermosetting resin pipe (RTRP) and glass–fiber–reinforced polymer mortar pipe (RPMP) are fiberglass pipes. Note 18212;For the purposes for this standard, polymer does not include natural polymers. 1.2 Inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 9.5. Note 28212;There is no known ISO equivalent to this standard.

Standard Test Method for Chemical Resistance of ldquo;Fiberglassrdquo; (Glassndash;Fiberndash;Reinforced Thermosetting-Resin) Pipe in a Deflected Condition