Q76 建筑暖通、空调器材设备 标准查询与下载

ANSI/ASHRAE 193P-2010 HVAC设备密封性的测定试验方法

Proposed new Standard 193 specifies a laboratory test for the airtightness of individual components in an HVAC system. Although ASHRAE Standards 62.2 and 152 address air leakage in HVAC systems as a whole, they do not provide a way to determine the airtightness of specific components in an HVAC system. Targeted at systems that move less than 3000 cfm (1400 L/s), Standard 193 will provide laboratory results that may be used by cognizant authorities who wish to regulate the air leakage of HVAC equipment and by contractors and installers that wish to specify and install equipment with known leakage characteristics.

Method of Test for Determining the Airtightness of HVAC Equipment

ANSI/AHRI 430-2010 中心站空调设备

This standard applies to central station air-handling units.

Central Station Air-Handling Units

ANSI/AHRI 365-2010 商业和工业单体式空气调节冷凝装置

This standard applies to factory-made Commercial and Industrial Unitary Air-Conditioning Condensing Units greater than or equal to 135,000 Btu/h as defined in Section 3.

Performance Rating of Commercial and Industrial Unitary Air-Conditioning Condensing Units

ANSI/AIHA Z9.9-2010 便携式通风系统

This Standard discusses portable ventilation equipment and systems used for the reduction, control or prevention of exposure to hazardous atmospheres or airborne substances in the occupational environment, and for provision of comfort to employees.

Portable Ventilation Systems

ANSI/AIHA Z9.10-2010 对工业场所的稀释通风系统设计和操作的基本调节

Fundamentals Governing the Design and Operation of Dilution Ventilation Systems in Industrial Occupancies

ASTM C1668-10 供暖、通风和空调(HVAC)系统中的刚性管道上的外部施用反射隔热系统的标准规范

1.1 This specification covers the requirements and physical properties of reflective insulation systems applied externally to Rigid Heating, Ventilation, and Air Conditioning (HVAC) duct systems operating at or below 250ºF (121.1 °C). These insulation systems consist of one or more low-emittance surfaces, such as metallic foil or metallic deposits, mounted on substrates to produce reflective air spaces. Reflective insulation systems derive their thermal performance from surfaces with an emittance of no greater than 0.1 facing enclosed air spaces. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Externally Applied Reflective Insulation Systems on Rigid Duct in Heating, Ventilation, and Air Conditioning (HVAC) Systems

ANSI/AHRI 366-2010 商业和工业单一空调冷凝机组的性能等级

This standard applies to factory-made Commercial and Industrial Unitary Air-Conditioning Condensing Units greater than or equal to 135,000 Btu/h as defined in Section 3.

Performance Rating of Commercial and Industrial Unitary Air-Conditioning Condensing Units

ANSI/AHRI 680(I-P)-2010 住宅空气过滤设备的性能等级评定

Performance Rating Of Residential Air Filter Equipment

ANSI/ASHRAE 94.3-2010 基于热力性能的有源敏感型热能设备测试方法

The purpose of this standard is to provide a standard procedure for determining the thermal performance of sensible thermal energy storage devices used in heating, air-conditioning, and service hot water systems.

Method of Testing Active Sensible Thermal Energy Devices Based on Thermal Performance

ANSI/AHRI 711(SI)-2010 液体线干燥剂性能等级

Performance Rating of Liquid-Line Driers

ANSI/AHRI 681(SI)-2010 住宅空气过滤设备的性能等级

Performance Rating Of Residential Air Filter Equipment

ASTM F2707-10 游泳池,温泉,热水浴池,和浅水池中避免吸入截留用限制吸入通风系统的安全设计和安装的安全性能标准规范

1.1 This safety performance specification provides requirements for safety in design and installation when using a suction-limiting vent system for suction entrapment prevention in swimming pools, spas, hot tubs, or wading pools. 1.2 The purpose of the vent is to relieve the vacuum at the suction outlet(s) caused by any blockage of the suction outlet(s). The vent is intended to prevent body entrapment at the suction outlet(s) and may also mitigate limb entrapment. It is not intended to prevent other injuries caused by the suction outlet(s) such as hair entrapment, mechanical entrapment, or evisceration. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Safety Performance Specification for Safe Design and Installation of Field Fabricated Suction-Limiting Vent Systems for Suction Entrapment Prevention in Swimming Pools, Spas, Hot Tubs, and Wading Pools

ANSI/AHRI 901-2010 冷却用蓄热器设备作业等级

This standard applies to Thermal Storage Equipment used for cooling which may be charged and discharged with any of a variety of heat transfer fluids. The equipment, as further described in Sections 3 and 4, may be fully factory assembled; assembled on site from factory supplied components; or field erected in accordance with pre-established design criteria.

Performance Rating of Thermal Storage Equipment Used for Cooling

ANSI/AHRI 580-2010 与低压离心液体冷却器一起使用的不可压缩式气体净化设备

This standard applies to Non-Condensable Gas Purge Equipment for use with Low Pressure Centrifugal Liquid Chillers as defined in Section 3. This standard defines general equipment requirements, test methods and analysis techniques used to determine the performance rating for Purge Equipment that remove Non-Condensable gases from Low Pressure Centrifugal Liquid Chillers. This purge equipment is typically used in conjunction with chillers which operate with at least a portion of the system below atmospheric pressure.

Non-Condensable Gas Purge Equipment For Use with Low Pressure Centrifugal Liquid Chillers

BS EN 1822-3:2009 高效空气过滤器(HEPA和ULPA).试验扁平片状过滤介质

This European Standard applies to high efficiency particulate air filters and ultra low penetration air filters (EPA, HEPA and ULPA) used in the field of ventilation and air conditioning and for technical processes, e.g. for applications in clean room technology or pharmaceutical industry. It establishes a procedure for the determination of the efficiency on the basis of a particle counting method using a liquid test aerosol, and allows a standardized classification of these filters in terms of their efficiency. This European Standard applies to testing sheet filter media used in high efficiency air filters. The procedure includes methods, test assemblies and conditions for carrying out the test, and the basis for calculating results.

High efficiency air filters (EPA, HEPA and ULPA) - Testing flat sheet filter media

DIN SPEC 13779:2009 非住宅建筑物的通风.通风和房间空调系统的性能要求.DIN EN 13779:2007-09的国家附件

Ventilation for non-residential buildings - Performance requirements for ventilation and room-conditioning systems - National Annex to DIN EN 13779:2007-09

DIN SPEC 1057-100:2009 独立式烟囱用建筑材料.第100部分:具有特殊属性的弧形砖

Building materials for Free-standing chimneys - Part 100: compass bricks with specific properties

AS/NZS 3823.2:2009 电器的性能.空气调节器和热泵.第2部分:能量标注和最低性能标准(MEPS)的要求

This Standard specifies the energy labelling requirements for single-phase non-ducted air conditioners of the vapour compression type and the minimum energy performance standard (MEPS) requirements for single-phase and three-phase air conditioners of the vapour compression type up to a rated total cooling capacity of 65 kW that fall within the scope of AS/NZS 3823.1.1, AS/NZS 3823.1.2 or AS/NZS 3823.1.3. Particular regulatory requirements for different categories of air conditioning equipment and validity dates are summarized in Appendix E of this Standard. This Standard does not specify electrical safety requirements. This Standard specifies the following values for cooling and heating, as applicable: (a) Rated power (input). (b) Rated capacity (output). (c) Energy Efficiency Ratio (EER) for cooling. (d) Coefficient of Performance (COP) for heating. (e) Annual Energy Efficiency Ratio (AEER) for cooling. (f) Annual Coefficient of Performance (ACOP) for heating. (g) Star Rating Index (SRI). (h) Star rating. (i) Some of the requirements for energy label validity. (j) The performance criteria for energy labelling validity. (k) Test report format. (l) Printing requirements for air conditioner appliance energy labels. (m) Minimum energy performance standard requirements for cooling and heating. (n) Power quality (power factor). 1.2 EXCLUSIONS The following equipment is excluded from the scope of this Standard: (a) Close controlled air conditioners within the scope of AS/NZS 4965 and chillers within the scope of AS/NZS 4776. (b) Multi-split systems (i.e., those having more than one indoor unit with an independent control for each indoor unit) pending the development of a suitable test method. MEPS levels are under consideration. (c) Evaporative coolers or any other cooling systems that are not of the vapour compression type. (d) Ground-water-sourced or ground-loop-sourced heat pumps within the scope of Part 1.3. NOTE: Water loop heat pumps as defined in Part 1.3 are included within the scope of this Standard. (e) Unbalanced air conditioners and spot coolers (these include some portable types). Regulatory requirements for these types are under consideration. (f) Single phase models that are designed for commercial applications, and where the requirements of (i), (ii) and (iii) below are met, are not required to display an Energy Rating label but are still required to be registered. (i) designed for and used only in non-residential applications; and (ii) not on display for sale through retail outlets; and (iii) not promoted in any catalogue or advertising material that could be interpreted as suitable for some residential applications. (g) Air conditioners powered by mains electricity specifically designed and sold only for installation in end-use mobile applications of caravans, mobile homes, camper vans and rail cars. (h) Models that have been granted exemption by the relevant Australian/New Zealand regulatory authority due to their specific design for application such as process heating or cooling, or for heating or cooling of spaces to conditions that are not intended for human comfort.

Performance of electrical appliances— Air conditioners and heat pumps Part 2: Energy labelling and minimum energy performance standard (MEPS) requirements

ISO/TS 21220:2009 一般通风用颗粒空气滤清器.过滤性能测定

Particulate air filters for general ventilation - Determination of filtration performance

DIN 18017-3:2009 无外窗浴室和洗手间的通风.第3部分:风扇通风

Ventilation of bathrooms and WCs without outside windows - Part 3: Ventilation by fans