Q81 供水、排水器材设备 标准查询与下载

BS EN 14428:2015 淋浴间外壳.功能要求和试验方法

Shower enclosures. Functional requirements and test methods

BS EN 1113:2015 卫生水龙头 1型和2型供水系统卫生水龙头花洒软管通用技术规范

Sanitary tapware. Shower hoses for sanitary tapware for water supply systems of type 1 and type 2. General technical specification

KS C IEC 61770:2015 水管连接用电气器具.软管组件与防逆流装置

Electric appliances connected to the water mains — Avoidance of backsiphonage and failure of hose-sets

DIN EN 14154-4:2015 水表. 第4部分: 其他功能; 德文版本EN 14154-4-2014

Water meters - Part 4: Additional functionalities; German version EN 14154-4:2014

DIN EN 16146:2015 卫生龙头配件. 1型和2型供应系统用卫生空头配件的可拔出淋浴软管. 通用技术规范; 德文版本EN 16146-2012+A1-2014

Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification; German version EN 16146:2012+A1:2014

ANSI/AWWA C704-2015 自来水厂用旋桨式计量表

Propeller-Type Meters for Waterworks Applications

ANSI/AWWA C606-2015 带槽和带肩的接头

Grooved and Shouldered Joints

NF D18-223*NF EN 16146+A1:2015 卫生设备配件.1型和2型供水系统卫生设备配件用可抽出淋浴软管.总体技术规范

La présente Norme européenne s'applique aux flexibles pour douchettes extractibles, quel que soit le matériau utilisé, destinés à équiper les robinetteries sanitaires des éviers et lavabos. Il convient que de tels flexibles ne soient raccordés qu'en aval de l'obturateur de la robinetterie. La robinetterie sera conforme à l'EN 200, l'EN 817, l'EN 1111, l'EN 1286 ou l'EN 1287.

Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification

ASME A112.4.2-2015 抽水马桶个人卫生装置

Personal hygiene devices for water closets

EN 15768:2015 材料对人类饮用水的影响 水可浸出有机物质的 GC-MS 鉴定

This European Standard describes a method for detecting and identifying organic chemicals that are amenable to GC-MS analysis using the procedures described and which can migrate from a product into water intended for human consumption. This European Standard does not provide all the necessary tools to completely identify all the substances that are detected. A method of semi-quantitatively estimating the concentrations of the organic substances detected is also provided, however, concentrations should only be seen as indicative. NOTE The method to be used for the preparation of migration waters is specified by separate ENs, as noted below.

Influence of materials on water intended for human consumption - GC-MS identification of water leachable organic substances

GOST R 56779-2015 饮用水热水供应分配系统. 能耗和有效性的计算方法

Systems of distribution of potable water hot-supply. Computational method of energy consumption and effectiveness

GOST R 54560-2015 纤维增强型热固性塑料管和管道部件. 规格

Fibre reinforced thermosetting plastic pipes and parts of pipelines. Specifications

ASTM A888-15 下水管, 雨水管, 污水管和排气管道用无衬套铸铁管和配件

1.1 This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, manufacture, mechanical and chemical properties, dimensions, coating, test methods, inspection, certification, and product marking for hubless cast iron soil pipe and fittings. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage. 1.2 The EDP/ASA numbers indicated in this section represent a Uniform Industry Code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are either new, special, or transitory and will be assigned numbers on subsequent prints of this specification. 1.3 This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the applicable requirements given in this specification.2 1.3.1 Lengths:   Figures EDP/ASA Identification Numbers for Hubless Pipe Fig. 1 10 ft (3.0 m) in sizes and 5 ft. (1.5 m) 11/2 , 2, 3, 4, 5, 6, 8, 10, 12, and 15 in. Fig. 1, Fig. 2 Method of Specifying Fittings Fig. 3 1.3.2 Fittings:  Quarter Bend Fig. 5 Quarter Bend, Reducing

Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

ASTM A74-15 铸铁污水管和其配件的标准规格

1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection, certification, product markings, dimensions, and dimensional tolerances for extra heavy and service cast iron soil pipe and fittings. These pipe and fittings are not intended for pressure applications as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage. 1.2 This specification covers pipe and fittings of the following patterns and, when so designated, shall apply to any other patterns that conform with the applicable requirements given in this specification. 1.2.1 Pipe:   Tables Extra heavy, 21/2 ft (0.75 m), 31/2 ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) lengths 1, 2 Service, 21/2 ft (0.75 m), 31/2 ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) 1, 2 Outside dimensions (for detailing) X1.1 1.2.2 Fittings:   Tables 1/4 bends; long 1/4 bends 3, 4 1/4 bends, long low-hub 5 1/4x......

Standard Specification for Cast Iron Soil Pipe and Fittings

GOST R 56380-2015 预绝缘管的供水网. 远程质量控制

Water supply networks of pre-insulated pipes. Distant control of quality

GOST R 53630-2015 供水和供暖系统的多层压力管道. 通用规格

Multilayer pressure pipes for water supply and heating systems. General specifications

JIS A 5207:2014 卫生器具

Sanitary wares

EN 16421:2014 饮用水中含有物质的影响 微生物生长的增加(EMG)

This European Standard specifies three methods for determining the ability of non-metallic materials to enhance the growth of micro-organisms. This European Standard is applicable to those materials destined to be used under various conditions for the transport and storage of water intended for human consumption. The standard allows for the testing of a single type of material, or a product in which only one material is in contact with water. It is unsuitable for use with assembled products where more than one material is exposed to water. NOTE The results given by each method are not directly comparable.

Influence of materials on water for human consumption - Enhancement of microbial growth (EMG)

NF T47-274*NF EN ISO 8029:2014 塑料软管.一般用途的纺织物增强的可折叠水管.规范

La présente Norme internationale spécifie les exigences pour quatre types de tuyaux d'eau écrasables thermoplastiques renforcés textiles destinés à des applications générales pour utilisation à des températures comprises entre -10 oC et 55 oC. Ces tuyaux sont classés selon les quatre types suivants :- basse pression, conçus pour une pression maximale de service jusqu'à 0,4 MPa (4,0 bar) à 23 oC et jusqu'à 0,2 MPa (2,0 bar) à 55 oC ;- moyenne pression, pour une pression maximale de service jusqu'à 0,7 MPa (7,0 bar) à 23 oC et jusqu'à 0,36 MPa (3,6 bar) à 55 oC ;- haute pression, pour une pression maximale de service jusqu'à 1,0 MPa (10,0 bar) à 23 oC et de 0

Plastics hose - General-purpose collapsible water hose, textile-reinforced - Specification

DIN EN ISO 4064-3:2014 可饮用冷水和热水表. 第3部分: 试验报告格式 (ISO 4064-3-2014); 德文版本EN ISO 4064-3-2014

Water meters for cold potable water and hot water - Part 3: Test report format (ISO 4064-3:2014); German version EN ISO 4064-3:2014