Q81 供水、排水器材设备 标准查询与下载

BS EN ISO 15876-2:2017 冷热水装置用塑料管道系统.聚丁烯.管道

Plastics piping systems for hot and cold water installations. Polybutene (PB). Pipes

BS EN ISO 15876-1:2017 冷热水装置用塑料管道系统.聚丁烯.总则

Plastics piping systems for hot and cold water installations. Polybutene (PB). General

BS EN 13598-2:2016 无压力地下排水和排污用塑料管道系统.非增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE).第2部分:检修孔和检查室用规范

Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE). Specifications for manholes and inspection chambers

JIS S 3201:2017 家用水净化器的试验方法

Testing methods for household water purifiers

ISO 15876-3:2017 热水和冷水装置用塑料管系统. 聚丁烯(PB). 第3部分: 配件

Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings

ISO 15876-5:2017 热水和冷水装置用塑料管系统. 聚丁烯(PB). 第5部分: 系统用配合性

Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system

ASME A112.19.3-2017 不锈钢管子附件

Stainless steel plumbing fixtures (Second Edition; Errata 1: May 2017; Errata 2: August 2017)

ISO 15876-1:2017 热水和冷水装置用塑料管系统. 聚丁烯(PB). 第1部分: 总则

Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 1: General

ISO 15876-2:2017 热水和冷水装置用塑料管系统. 聚丁烯(PB). 第2部分: 管

Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes

ASTM C1628-17 使用橡胶垫圈的混凝土重力排水管接头的标准规格

1.1 This specification covers flexible leak resistant joints for concrete gravity flow sewer pipe using rubber gaskets for sealing the joints, where measurable or defined infiltration or exfiltration is a factor of the design. The specification covers the design of joints and the requirements for rubber gaskets to be used therewith, for pipe conforming in all other respects to Specifications C14, C76, C655, C985, and C1417, provided that, if there is conflict in permissible variations in dimension, the requirements of this specification shall govern for joints. Note 1: Infiltration or exfiltration quantities for an installed pipeline are dependent upon many factors other than the joints, and allowable quantities must be covered by other specifications and suitable testing of the installed pipeline and system. This specification covers the design, material, and performance of the rubber gasket joint only. Joints covered by this specification are for hydrostatic pressures up to 13 psi without leakage, when plant tested in accordance with Section 10. 1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Joints for Concrete Gravity Flow Sewer Pipe, Using Rubber Gaskets

ASTM A1105-17 波纹钢人孔组件的标准规格

1.1 This specification covers the manufacture and purchase requirements of products used for assembly and construction of circular reinforced corrugated steel manholes used in sewer and water works. Products covered by this specification are not normally used for the conveyance of sanitary or industrial wastes. The steel sheet used in fabrication of the manhole structures has a protective metallic coating of zinc (galvanizing), aluminum, 55 % aluminum-zinc alloy, or zinc-58201;% aluminum-mischmetal alloy, or a polymer pre-coating. 1.2 Part I, Sections 1 through 11, of this specification presents general requirements and requirements that are common to each corrugated steel product in the sections outlined in 1.3. 1.3 Part II of this specification presents specific requirements for each manhole product in the following section: Product Section Grade Rings 12 Manhole Structures 13 Base Section 14 Steps and Ladders 15 1.4 Steel sheet with zinc, aluminized or polymeric coating may be specified for the fabrication of the manhole structures. Manhole structures made from sheets with composite coatings are always furnished with an approved coating. Note 1: Pipe fabricated with polymeric coated sheet may be used for sanitary sewers and industrial applications. Note 2: This specification is a manufacturing specification and purchase specification only and does not include requirements for backfill, or the relationship between field load conditions. 1.5 This inter

Standard Specification for Corrugated Steel Manhole Assemblies

ASTM A74-17 铸铁污水管和配件的标准规格

1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection, certification, product markings, dimensions, and dimensional tolerances for extra heavy and service cast iron soil pipe and fittings. These pipe and fittings are not intended for pressure applications as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage. 1.2 This specification covers pipe and fittings of the following patterns and, when so designated, shall apply to any other patterns that conform with the applicable requirements given in this specification. 1.2.1 Pipe:   Tables Extra heavy, 21/2 ft (0.75 m), 31/2 ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) lengths 1, 2 Service, 21/2 ft (0.75 m), 31/2 ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) 1, 2 Outside dimensions (for detailing) X1.1 1.2.2 Fittings:   Tables 1/4 bends; long 1/4 bends 3, 4 1/4 bends, long low-hub 5 1/4 ben

Standard Specification for Cast Iron Soil Pipe and Fittings

ASTM F2536-17 安装悬吊于等内板材的塑料排水, 排渣与放气管道的标准指南

4.1 This guide is for use by designers, specifiers, installation contractors, regulatory agencies, owners and inspection organizations who are involved in these piping installations in buildings of this type. 1.1 This guide provides procedures for the installation of DWV piping in buildings that are built where soil conditions require the use of pier or piling supported grade beam construction or in filled ground where the soil compaction is less than 958201;%. These procedures are intended to ensure that the DWV piping suspended from the on grade concrete slabs is not damaged or destroyed by movement of the soil or fill under the slab after the building is completed and occupied. 1.2 In this type of construction, the area within the grade beams is filled with soil up to a level that allows the concrete slab to be poured directly on the fill without a supporting form. In this process the sanitary waste piping is installed by trenching into the fill, and then putting hangers with support rods on the pipes as they are installed. The hanger rods extending upward must be long enough so that the top of the rod will be embedded in and anchored in the concrete. 1.3 The hanger rods are intended to provide adequate strength and corrosion resistance to assure long term service. 1.4 The details of installation are intended to ensure that the rods remain vertical, that they extend into the concrete an adequate amount and that the upper ends are terminated so that they have adequate “pull out” strength. 1.5 The details of backfill are intended to limit or minimize the loads on the a suspended piping. These loads result from consolidation or movement of the soil/fill beneath the slab. 1.6 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Installing Plastic DWV Piping Suspended from On-Grade Slabs

BS EN 13618:2016 饮用水装置中的柔性软管组件 功能要求和测试方法

Flexible hose assemblies in drinking water installations. Functional requirements and test methods

JIS A 5706:2016 未增塑聚氯乙烯檐口滴水沟和落水管

Unplasticized polyvinyl chloride eaves gutters and downspouts

DIN EN 12897:2016 供水.间接加热的未放气（封闭）储水式热水器的规范.德文版本EN 12897-2016

Water supply - Specification for indirectly heated unvented (closed) storage water heaters; German version EN 12897:2016

DIN EN 14527:2016 家用淋浴盆;德文版本EN 14527-2016

Shower trays for domestic purposes; German version EN 14527:2016

DIN EN 12566-7:2016 50 PT以下小型废水处理系统.第7部分:预制三级处理装置.德文版本EN 12566-7-2016

Small wastewater treatment systems for up to 50 PT - Part 7: Prefabricated tertiary treatment units; German version EN 12566-7:2016

DIN EN 12566-4:2016 50PT以下小型废水处理系统.第4部分:预制袋就地组装的化粪池.德文版本EN 12566-4-2016

Small wastewater treatment systems for up to 50 PT - Part 4: Septic tanks assembled in situ from prefabricated kits; German version EN 12566-4:2016

DIN EN 12566-3:2016 50 PT以下的小型废水处理系统. 第3部分:包装的和/或现场装配的家用废水处理设备.德文版本EN 12566-3-2016

Small wastewater treatment systems for up to 50 PT - Part 3: Packaged and/or site assembled domestic wastewater treatment plants; German version EN 12566-3:2016