共找到 118 条与 城市道路器材设备 相关的标准,共 8 页
Vertical road signs - Portable deformable warning devices and delineators - Portable road traffic signs - Cones and cylinders.
Vertical road signs - Portable deformable warning devices and delineators - Portable road traffic signs - Cones and cylinders.
Road traffic noise reducing devices - Procedures for assessing long term performance - Part 1 : acoustical characteristics.
This European Standard specifies the initial performance requirements and laboratory test methods for retroreflecting road studs intended for use as permanent and temporary road marking materials.
Road marking materials - Retroreflecting road studs - Initial performance requirements
Road marking materials - Road marking performance for road users.
Road marking materials - Road marking performance for road users.
1.1 This specification covers flexible, non-exposed glass bead lens and microprismatic, retroreflective sheeting designed for use on traffic control signs, delineators, barricades, and other devices. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Retroreflective Sheeting for Traffic Control
Covers the requirements for the design and erection of temporary stands that provide seating or accommodation for spectators.Requirements for access to and egress from the stands are also covered.
Temporary stands
Road restraint systems - Part 5 : products requirements and evaluation of conformity for vehicle restraint systems.
Road restraint systems - Part 5 : products requirements and evaluation of conformity for vehicle restraint systems.
Road Traffic Signal Systems - Part 400: Traffic Management Systems
This European Standard specifies requirements for evaluation of conformity of the following vehicle restraint systems: a) safety barriers; b) crash cushions; c) terminals (will be effective when ENV 1317-4 becomes an EN); d) transitions (will be effective when ENV 1317-4 becomes an EN); e) vehicle / pedestrian parapets (only for the vehicle restraint function). Pedestrian parapet requirements are not covered in this document. Requirements for the evaluation of durability with respect to weathering are included in this document. Requirements for other forms of durability (e.g. marine environment, sand abrasion) are not included. Temporary barriers are not within the scope of this document.
Road restraint systems - Part 5: Product requirements and evaluation of conformity for vehicle restraint systems(includes Amendment A1:2008); English version of DIN EN 1317-5:2008-10
This British Standard specifies requirements for access cover systems manufactured from steel or aluminium and with a clear opening greater than 1 m for installations within areas subject to pedestrian and/or slow moving vehicular traffic, for use as covers over chambers and ducts. NOTE For clear openings up to 1 m, BS EN 124 applies. This standard establishes definitions; materials; design; structural performance; technical documentation; installation and operating guidance notes; warning notes; testing requirements; verification and marking of such access cover systems.
Specification for steel and aluminium access cover systems with over 1 m clear opening
Gives recommendations for the design and performance of the most common types of bridge bearings.
Structural bearings - The design of bridge bearings
Covers three categories of retro-reflective roadstuds intended to be fitted onto or into road surfaces for use as supplementary road marking. Does not cover (a) temporary roadstuds; (b) the method of securing the roadstuds to the road surface; (c) the po
Roadstuds
This European Standard defines the means for evaluating the acoustic durability of Road Traffic Noise Reducing Devices In this European Standard, the sound absorption is characterised by the single-number rating of sound reflection DLRL) as defined in CEN/TS 1793-5. The airborne sound insulation is characterised by single-number rating of airborne sound insulation DLsl as defined in CEN/TS 1793-5.
Road traffic noise reducing devices - Procedures for assessing long term performance - Part 1: Acoustical characteristics; English version of DIN EN 14389-1:2008-02
This European Standard specifies performance requirements and defines levels in passive safety terms intended to reduce the severity of injury to the occupants of vehicles impacting with the permanent road equipment support structures. Consideration is also given to other traffic and pedestrians. Three energy absorption types are considered and test methods for determining the level of performance under various conditions of impact are given. This European Standard excludes vehicle restraint systems, noise barriers and transilluminated traffic bollards. It also excludes temporary traffic control devices.
Passive safety of support structures for road equipment - Requirements, classification and test methods
Lays down requirements for the location of holes for the positioning of fencing wires in 6 types of fencing posts and droppers.
Hole location in fencing posts and droppers
This European Standard specifies performance requirements and defines levels in passive safety terms intended to reduce the severity of injury to the occupants of vehicles impacting with the permanent road equipment support structures. Consideration is also given to other traffic and pedestrians. Three energy absorption types are considered and test methods for determining the level of performance under various conditions of impact are given. This European Standard excludes vehicle restraint systems, noise barriers and transilluminated traffic bollards. It also excludes temporary traffic control devices.
Passive safety of support structures for road equipment - Requirements, classification and test methods; English version of DIN EN 12767:2008-01
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号