T04 基础标准与通用方法 标准查询与下载
共找到 1071 条与 基础标准与通用方法 相关的标准，共 72 页
This part of ISO 11451 specifies methods for testing the immunity of passenger cars and commercial vehicles to electromagnetic disturbances from on-board transmitters connected to an external antenna and portable transmitters with integral antennas, regardless of the vehicle propulsion system (e.g. spark ignition engine, diesel engine, electric motor).
Road vehicles - Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 3: On-board transmitter simulation
- ICS
- 33.100.20;43.040.10
- CCS
- T04
- 发布
- 2015-06
- 实施
This part of ISO 11451 specifies general conditions, defines terms, gives practical guidelines, and establishes the basic principles of the vehicle tests used in the other parts of ISO 11451, for determining the immunity of passenger cars and commercial vehicles to electrical disturbances from narrowband radiated electromagnetic energy, regardless of the vehicle propulsion system (e.g. spark-ignition engine, diesel engine, electric motor). The electromagnetic disturbances considered are limited to continuous narrowband electromagnetic fields. A wide frequency range (0,01 MHz to 18000 MHz) is allowed for the immunity testing in this and the other parts of ISO 11451.
Road vehicles - Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 1: General principles and terminology
- ICS
- 33.100.20;43.040.10
- CCS
- T04
- 发布
- 2015-06
- 实施
Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 8: Immunity to magnetic fields
- ICS
- 33.100.20;43.040.10
- CCS
- T04
- 发布
- 2015-06
- 实施
Road vehicles - Test procedures for evaluating child restraint system interactions with deploying air bags
- ICS
- 43.040.80
- CCS
- T04
- 发布
- 2015-03
- 实施
Measurement of noise emitted by accelerating road vehicles. Engineering method. M and N categories
- ICS
- 17.140.30;43.020
- CCS
- T04
- 发布
- 2015-01-31
- 实施
- 2015-01-31
Single road vehicles. Test methods for compliance assessment
- ICS
- 13.040.30
- CCS
- T04
- 发布
- 2015
- 实施
- 2017-04-01
Motor vehicles. Test procedures of brake discs drums on the inertia bench
- ICS
- 43.040.40
- CCS
- T04
- 发布
- 2015
- 实施
- 2017-04-01
State system for ensuring the uniformity of measurements. Automatic instruments for weighing road vehicles in motion and measuring axle loads. Methods of verification
- ICS
- 17.100
- CCS
- T04
- 发布
- 2015
- 实施
- 2016-09-01
Testing and measuring instruments for vehicles. Technical requirements and test methods
- ICS
- 43.040.30
- CCS
- T04
- 发布
- 2015
- 实施
- 2017-01-01
Automotive Vehicles. Controls for disabled drivers with dysfunction of the hands and feet. Technical requirements and test methods
- ICS
- 43.060.40
- CCS
- T04
- 发布
- 2015
- 实施
- 2017-04-01
Road vehicles. Open Test sequence eXchange format (OTX). Core data model specification and requirements
- ICS
- 43.020
- CCS
- T04
- 发布
- 2014-11-30
- 实施
- 2014-11-30
This British Standard specifies requirements for automotive vehicle (vehicle,see 2.1) damage repair processes undertaken at fixed facilities or through provision of a mobile service and includes requirements for: a)repair processes; b)competence of personnel; c)tools and equipment; d)parts and controlled consumables; e)repair process management; f)quality control; g)complaints procedure. This British Standard also specifies the information to be included in any claim of conformity.
Automotive services. Specification for vehicle damage repair processes
- ICS
- 43.040.60
- CCS
- T04
- 发布
- 2014-11-30
- 实施
- 2014-11-30
Road vehicles - Measurement of driver visual behaviour with respect to transport information and control systems - Part 1: Definitions and parameters (ISO 15007-1:2014)
- ICS
- 01.040.43;43.040.15;43.040.30
- CCS
- T04
- 发布
- 2014-11
- 实施
This part of ISO 15007 defines key terms and parameters applied in the analysis of driver visual behaviour focused on glance and glance-related measures. These terms and parameters can be applied in environments from real-world driving experiments to laboratory-based driving simulator studies. The procedures described in this part of ISO 15007 could also apply to more general assessments of driver visual behaviour without the introduction of TICS-specific systems. The parameters and definitions described below are intended to assist development of a common source of reference for driver visual behaviour data. Minimum requirements for reporting the results of Transport Information and Control Systems (TICS) evaluations are provided. Further guidance including the specification of how to analyse and present the results of studies of visual behaviour is available in other ISO publications (see, for example, ISO 2854 and ISO/TR 13425:2006). However, data collected and analysed according to this standard will allow comparisons to be performed across different TICS applications and experimental scenarios.
Road vehicles - Measurement of driver visual behaviour with respect to transport information and control systems - Part 1: Definitions and parameters
- ICS
- 13.180;43.040.15
- CCS
- T04
- 发布
- 2014-11
- 实施
Road vehicles. Multimedia data exchange format for impact tests
- ICS
- 43.020
- CCS
- T04
- 发布
- 2014-09-30
- 实施
- 2014-09-30
Procedure to construct injury risk curves for the evaluation of road user protection in crash tests
- ICS
- 43.020
- CCS
- T04
- 发布
- 2014-09-30
- 实施
- 2014-09-30
Road vehicles - Measurement of driver visual behaviour with respect to transport information and control systems - Part 2: Equipment and procedures
- ICS
- 13.180;43.040.15;43.040.30
- CCS
- T04
- 发布
- 2014-09-01
- 实施
Dieser Teil der Norm enthält allgemeine Informationen und Strukturen der einzelnen Teile der Normenreihe. Außerdem werden Anwendungsfälle in Bezug auf Systeme für Reparatur- und Wartungsinformationen (RMI) festgelegt, die der Standardisierung des Zugangs auf RMI durch unabhängige Marktteilnehmer dienen. Dieser Teil der Norm beschreibt die auf den standardisierten Zugang zu RMI zutreffenden Anwendungsfälle. Die Anwendungsfälle spiegeln reale Szenarien wider (z. B. bei der Instandhaltung von Fahrzeugen), der für den Zugang zu Informationen erforderlich ist, um Pannenhilfe, Untersuchungen, Diagnose, Reparaturen und Wartungen, sowie die Neuprogrammierung und Ersatz elektronischer Steuergeräte (ECUs), durchzuführen. RMI-Systeme, die vom Personal für die Durchführung von Instandhaltungsleistungen verwendet werden, bestehen aus: - einem webbasierten System, das Zugang zu RMI gewährt, die für die Durchführung von Instandhaltungsleistung(en) erforderlich ist (sind); - liefert spezifische RMI-Kontaktinformationen; - einem Sicherheitsrahmen, mit dem der Zugang zu diebstahlrelevanten RMI geschützt wird. Dieser Teil der Norm gibt einen Überblick über die gesamte Norm und deren Anwendung auf die Automobilindustrie. Dieser Teil der Norm gilt für leichte Personenkraftwagen und Nutzfahrzeuge, wie in der Verordnung (EG) 715/2007, Art. 2 festgelegt.
Road vehicles - Standardized access to automotive repair and maintenance information (RMI) - Part 1: General information and use case definition
- ICS
- 43.040.15;43.180
- CCS
- T04
- 发布
- 2014-09
- 实施
Dieser Teil von ISO 18541 umfasst Anforderungen an die funktionale Nutzerschnittstelle in Bezug auf Reparatur- und Wartungsinformationssysteme (RMI), die der Standardisierung des Zugangs zu RMI durch unabhängige Marktteilnehmer dienen. In diesem Teil von ISO 18541 sind alle Anforderungen an die funktionale Nutzerschnittstelle angegeben, die sich auf das RMI-System eines Fahrzeugherstellers beziehen. Diese Anforderungen spiegeln die Bedürfnisse wider, die von denen in ISO 18541-1 beschriebenen Anwendungsfällen abgeleitet sind.
Road vehicles - Standardized access to automotive repair and maintenance information (RMI) - Part 3: Functional user interface requirements
- ICS
- 43.040.15;43.180
- CCS
- T04
- 发布
- 2014-09
- 实施
Road vehicles - Standardized repair and maintenance information (RMI) terminology - Part 2: Standardized process implementation requirements, Registration Authority (ISO 18542-2:2014); German version EN ISO 18542-2:2014
- ICS
- 43.040.15;43.180
- CCS
- T04
- 发布
- 2014-09
- 实施
