T33 润滑件、密封件、联接件 标准查询与下载

SAE J1918-2002 汽车密封层膨胀率和吸水率测定方法

This SAE Recommended Practice sets forth methods for determining total expansion gravimetrically and volumetrically, calculating vertical expansion and measuring the water absorption of cut and uncut sealer beads.

Method for the Determination of Expansion and Water Absorption of Automotive Sealers

SAE J2337/3-2002 流体动力和高压的连接,采用带有ISO 261螺纹及O形圈密封的端口,双头螺栓端及塞子 第3部分:端口塞堵要求,尺寸,设计和测试方法

The purpose of SAE J 2337 specifies dimensions, design, and performance requirements for eight plugs using a conical seal to insure leak proof performance with a design factor of 4 to 1. These connectors are intended for general and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These connectors are capable of providing leak proof full flow connections in hydraulic systems operating from 95 kPa vacuum to the working pressures shown in Table 1. Since many factors influence the pressure at which hydraulic systems will or will not perform satisfactorily, these values should not be construed as guaranteed minimums. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and manufacturer to ensure that the required performance levels are met.

Connections for Fluid Power and High Pressure UsePorts, Stud Ends, and Plugs with ISO 261 Threads and O-Ring SealingPart 3: Port Plug Requirements, Dimensions, Design, and Test Methods

DLA MS35252 REV A VALID NOTICE 1-2002 矩形连接环

MS35252A remains inactive for new design, however, the document is valid for use.

RING, CONNECTING, RECTANGULAR

ISO 4086:2001 道路车辆 半挂车牵引座的90号连接销 互换性

This International Standard specifies the characteristics of the 90 [89 mm (3,5") diameter] semi-trailer fifth wheel kingpin used for coupling extra-heavy-duty vehicles exceeding the limitations of weight generally laid down by official requirements. It is applicable to fifth wheel kingpins intended for engaging 90 fifth wheels as defined in ISO 3842 . This International Standard also specifies the dimensional characteristics required for mounting and interchangeability. NOTE The dimensions of the 50 semi-trailer fifth wheel kingpin, normally used to couple semi-trailers to tractors in compliance with mass limitations usually set by compulsory regulations, are given in ISO 337 .

Road vehicles - 90 semi-trailer fifth wheel kingpin - Interchangeability

ISO 1102:2001 商用道路车辆 直径50mm的牵引杆连接器 互换性

This International Standard specifies the characteristics of 50 mm drawbar eyes, necessary for the interchangeability of the coupling components on trailers and permitting interchangeability between towing vehicles and trailers equipped with these components. This International Standard is applicable to mechanical connections designed for commercial vehicles and trailers, the maximum total mass of which is above 3,51.

Commercial road vehicles - 50 mm drawbar eye - Interchangeability

ISO 8755:2001 商用道路车辆 40mm牵引挂钩孔 互换性

This International Standard specifies the characteristics of 40 mm drawbar eyes, necessary for the interchangeability of the coupling components on trailers and permitting interchangeability between towing vehicles and trailers equipped with these components. This International Standard is applicable to mechanical connections designed for commercial vehicles and trailers, the maximum total mass of which is above 3,5 t.

Commercial road vehicles - 40 mm drawbar eye - Interchangeability

ISO 11406:2001 商用道路车辆 带尾部连接器的牵引车辆和牵引杆式挂车间的机械连接 互换性

This International Standard specifies the requirements for the various elements and dimensions of towing vehicles with rear-mounted coupling and of drawbar trailers, to ensure interchangeability. NOTE Annex B gives examples of different configurations of vehicle combinations; this International Standard deals only with No. B.1.1. This International Standard is applicable to road trains for commercial transport of cargo of the greatest possible variety; it does not cover dedicated or special combinations. Nor does it specify limitations of maximum gross mass and overall dimensions, which are generally laid down by legislative requirements. Vehicles whose couplings form the subject of this International Standard are not interchangeable with vehicles whose couplings are mounted forward and below (which form the subject of ISO 11407 [1]).

Commercial road vehicles - Mechanical coupling between towing vehicles with rear-mounted coupling and drawbar trailers - Interchangeability

SAE J646-2000 行星齿轮术语

The following figures illustrate in simplified form the more common planetary gear arrangements in order to establish applicable terminology. Gear ratio is the numerical ratio of input to output speed.

Planetary Gear(s) Terminology

JB/T 10189-2000 汽车用等速万向节及其总成

　　本标准规定了汽车用等速万向节及其总成的定义、类型、结构、尺寸及技术要求。 本标准适用于汽车用等速万向节及其总成,供制造厂生产检验和用户验收收。

Constant velocity universal joints and assemblies for automobiles

SAE J2512-1999 牵引设备等级和规范

This SAE Recommended Practice applies to all trucks that are equipped with armlift bodies, carrier bodies, wheel lift bodies, wrecker, and underlift bodies. Additional rating methods are provided for tow slings, truck hitches, and chain assemblies. The purpose of this document is to establish guidelines for rating towing and recovery equipment and carriers. It is applicable to all towing and recovery equipment manufacturers.

Towing Equipment Ratings and Practices

QC/T 271-1999 微型货车防雨密封性试验方法

本标准规定了微型货车防雨密封性试验方法。 　　本标准适用于微型货车(含微型厢式货车)，也适用于微型客车及其变型车。

Test method for rain-tightness of minivans

SAE J2211-1998 HFC-134a(R-134a)密封装置的推荐服务过程

Refrigerant containment is an important part of servicing mobile air- conditioning (A/C) A/C systems. This procedure provides guidelines for technicians for servicing mobile A/C systems and operating refrigerant recycling equipment designed for HFC-134a (R-134a) (described in SAE J2210).

Recommended Service Procedure for the Containment of HFC-134a (R-134a)

JIS D 1611:1995 汽车零部件.润滑油过滤器试验方法

Automotive parts -- Test methods of lubricating oil filters

JIS D 2612:1995 汽车零件.使用非石油基液压制动液的液压制动主油缸的油缸密封件

Automotive parts -- Reservoir seals for hydraulic brake master cylinders using a non-petroleum base hydraulic brake fluid

SAE J1604-1995 筒式液压制动分泵橡胶罩

This SAE Standard covers molded rubber boots used as end closures on drum- type wheel brake actuating cylinders to prevent the entrance of dirt and moisture, which could cause corrosion and otherwise impair wheel brake operation. The document includes performance tests of brake cylinder boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition, tensile strength, or elongation of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operation in a temperature range of -40 to +120 degrees C ? degrees C (-40 to +248 degrees F ?.6 degrees f).

Rubber Boots for Drum-Type Hydraulic Brake Wheel Cylinders

WJ 186-1994 装甲车辆标准零件 密封毡圈

Sealing felt ring of standard parts of armored vehicles

WJ 225-1994 装甲车辆标准零件 模锻式合页

Forged hinges, standard parts for armored vehicles

WJ 227-1994 装甲车辆标准零件 方形扣环

Armored Vehicle Standard Parts Square Buckle

WJ 188-1994 装甲车辆标准零件 自紧油封

Self-tightening oil seal for standard parts of armored vehicles

WJ 2142-1993 装甲车辆柴油机机油滤清器纸质滤芯规范

本规范规定了装甲车辆柴油机机油滤清器纸质滤芯的主要技术要求、质量保证规定和交货准备等内容。 本规范适用于装甲车辆柴油机体积流量在400 L／min以下的机油滤清器纸质滤芯的设计、制造和验收。

Specification for paper filter element of armored vehicle diesel engine oil filter