T38 照明与信号设备 标准查询与下载

CAS 139-2006 机动车用三角电子警告牌

本标准规定了机动车用三角电子警告牌的技术要求、试验方法、检验规则等。 本标准适用于机动车随车携带的、使用时放置在道路上，能昼夜发出警告信号以表示停驶机动车存在的警告装置。

Electronic Warning Triangle for Motor Vehicle Use

SAE J1383-2006 替换圆头机动车前照灯的性能要求

This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements, material requirements, design requirements, and design guidelines for headlamps.

Performance Requirements for Replacement Bulb Motor Vehicle Headlamps

SAE J567-2006 灯泡固定系统

This SAE Standard references the performance and functional requirements of the International Electrotechnical Commission (IEC) and its U.S. member, the American National Standards Institute (ANSI). By referring to IEC/ANSI and its standards concerning bulb sockets, lamp holders, and gages, this document recognizes the need for harmonized standards world-wide for what are typically commodity items. Additional requirements are noted.

Lamp Bulb Retention System

DLA MS51302 REV B VALID NOTICE 3-2006 24伏车载灯火管制红色尾灯

MS51302B, dated 14 September 2001, remains inactive for new

STOPLIGHT, VEHICULAR-BLACKOUT, 24 VOLT

BS ISO 22168:2006 道路车辆.影响来自光源的光色的覆层保持试验.试验方法

The aim of ISO 22168:2006 is to define a method to test the durability of the coating of the bulb in order to meet the colorimetry of applicable normative requirements of this International Standard.

Road vehicles - Holding test of coatings influencing the colour of light emitted by light sources) - Test methods

SAE J1373-2006 全长低于9.1 m的电动机车用后角灯

This SAE Recommended Practice provides test procedures, requirements, and guidelines for rear cornering lamps for use on vehicles less than 9.1 m in overall length.

Rear Cornering Lamps for Use on Motor Vehicles Less Than 9.1 m in Overall Length

SAE J2595-2006 封闭光线发电机机车照灯的性能要求

This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements, material requirements, design requirements, and design guidelines for sealed beam headlamps.

Performance Requirements for Sealed Beam Motor Vehicle Headlamps

ISO 22168:2006 道路车辆.影响光源光色的涂层的保持试验.试验方法

The aim of this International Standard is to define a method to test the durability of the coating of the bulb in order to meet the colorimetry of applicable normative requirements of this Standard.

Road vehicles - Holding test of coatings influencing the colour of light emitted by light source(s) - Test methods

SAE J1432-2006 总体宽度等于或超过2032mm的车辆中使用的背面高安装的停止灯和背面高安装的转弯信号灯

This SAE Recommeded Practice provides test procedures, requirements, and guidelines for high-mounted stop lamps and high-mounted turn signal lamps intended for use on vehicles 2032 mm or more in overall width. This document applies to trucks, motor coaches, van type trailers, and other vehicles with permanent structure greater than 2800 mm high. This document does not apply to school buses, truck tractors, pole trailers, flat-bed trailers, pick-up truck with dual wheels and trailer converter dollies. The purpose of the high-mounted stop lamp(s) and high-mounted turn signal lamp(s) is to provide a signal over intervening vehicles to the driver of following vehicles.

Rear High Mounted Stop Lamps and Rear High Mounted Turn Signal Lamps for Use on Vehicles 2032 mm or More in Overall Width

SANS 1376-2:2006 机动车辆用灯具．第2部分：头灯

Covers the requirements for the photometric properties of headlights emitting an asymmetrical dipped beam or a main beam, or both, and used in headlight systems meeting left-hand rule-of-road requirements.

Lights for motor vehicles Part 2: Headlights

SANS 1376-3:2006 机动车辆用灯具．第3部分：辅灯

Covers the photometric characteristics of secondary lights for vehicles (i.e. position lights, stop lights, direction-indicator lights, parking lights, reversing lights, rear registration-plate lights and end-outline marker lights) and of assemblies of t

Lights for motor vehicles Part 3: Secondary lights

SAE J2087-2006 日间开动指示灯

This SAE Recommended Practice provides test procedures, requirements, and guidelines for a daytime running light (DRL) function.

Daytime Running Light

SAE J278-2006 雪上汽车刹车灯

This document provides test methods and requirements for the stop lamp on snowmobiles.

Snowmobile Stop Lamp

SAE J279-2006 雪上汽车尾灯（后方灯）

The SAE document provides test methods and requirements for tail lamps for snowmobiles.

Snowmobile Tail Lamp (Rear Position Lamp)

JIS D 0032:2006 道路车辆.控制装置、指示仪、信号装置的符号

この規格は，乗用車，小型 大型商用車及びバスの運転時に確実に認識でき，かつ，使用しやすいような操作装置，計量装置及び警報装置に用いる識別記号について規定する。

Road vehicles -- Symbols for controls, indicators and tell-tales

SAE J280-2006 雪地汽车前灯

This standard provides test methods and requirements for snowmobile headlamps.

Snowmobile Headlamps

SAE USCAR14-2006 测试汽车卤素光源的规范

The procedures contained in this specification cover the laboratory testing of replaceable halogen incandescent bulbs for use in automotive road illumination. The following tests are intended to be run under the following conditions - new bulb design - design or process change made to an existing bulb, which could affect the outcome of the test - the completion of one calendar year, accept as noted in the following Test Schedule Table.

Specification for testing automotive halogen light sources

DLA MS51319 REV B NOTICE 2-2006 24伏防水服务前灯

MS51319B is inactive for new design and is no longer used, except for replacement purposes.

HEADLIGHT, SERVICE, 24-VOLT, WATERPROOF

DLA MS51073 REV A NOTICE 3-2006 24伏直流电圆屋顶灯

MS51073A is inactive for new design and is no longer used, except for replacement purposes.

LIGHT, DOME: 24 VOLT DC

KS C IEC 60809:2005 道路车辆用白炽灯.尺寸、电气和照明要求

이 규격은 도로 차량용 전조등, 안개등, 신호등에 사용되는 교체용 램프(필라멘트 램프와

Lamps for road vehicles－Dimensional, electrical and luminous requirements