T38 照明与信号设备 标准查询与下载

BS ISO 16844-1:2013 道路车辆. 速度记录器系统. 电连接器

Road vehicles. Tachograph systems. Electrical connector

SAE J222-2013 前位灯

This SAE Standard provides test procedures, requirements, and guidelines for a Front Position lamp.

Front Position Lamp

SAE J2999-2013 通过设计分析有效的投投射光镜头区域(EPLLA)的测定

This SAE Standard provides a method for determining the Effective Projected Luminous Lens Area (EPLLA) of a lamp function using design analysis. This standard was created to clarify and address how to determine EPLLA with traditional and new technologies. Lamps can be evaluated using the method described in SAE J 3333; however, no lamp is subjected to both methods.

Determination of the Effective Projected Luminous Lens Area (EPLLA) by Design Analysis

NF R13-629/A5:2013 道路车辆用灯.尺寸规格、电气和照明要求

Lamps for road vehicles - Dimensional, electrical and luminous requirements

IEC 60810:2003/AMD2:2013 道路机动车辆用灯.性能要求.修改件2

Lamps for road vehicles - Performance requirements; Amendment 2

GA/T 1004-2012 校车标志灯

本标准规定了校车标志灯的术语和定义要求，试验方法、检验规则和安装要求等。 本标准适用于取得校車使用許可、用於接送 3 周歲以上學齡前幼兒及接受義務教育的學生上下學 的7 座以上的載客汽車。

school bus lights

SAE J2357-2012 电子驱动和/或控制外汽车照明设备的应用指南

This SAE Recommended Practice is intended as a guide toward standard and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements, design requirements, design requirements and design guidelines for electronic devices.

Application Guidelines for Electronically Driven and/or Controlled Exterior Automotive Lighting Equipment

SAE J1849-2012 应急车辆警报器

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice provides laboratory test procedures, requirements and guidelines for electronic siren systems with a single loudspeaker, and electromechanical sirens for use on authorized emergency vehicles, which call for the right-of-way. Test procedures and performance requirements for individual system components are not included in this version. Results obtained for a siren system with a speaker array that

Emergency Vehicle Sirens

JJF 1360-2012 滑行时间检测仪校准规范

本规范适用于汽车排气污染物检测用底盘测功机校准用滑行时间检测仪的校准。

Calibration Specification for Coast-down Time Testers

BS ISO 27145-2:2012 道路车辆. 全球统一的车载诊断系统 (WWH-OBD) 的通信实施要求. 公共数据字典

Road vehicles. Implementation of World-Wide Harmonized On-Board Diagnostics (WWH-OBD) communication requirements. Common data dictionary

SAE J578-2012 颜色规格

This SAE Standard defines and provides a means for the control of colors employed in motor vehicle external lighting equipment, including lamps and reflex reflectors. The document applies to the overall effective color of light emitted by the device in any given direction and not to the color of the light from a small area of the lens. It does not apply to pilot, indicator, or tell-tale lights.

Color Specification

IEC 60809:1995/AMD5:2012 道路车辆用灯.尺寸规格,电气和照明要求.修改件5

Replace the fourth paragraph by the following: For most of the requirements given in this standard, reference is made to the “relevant lamp data sheet”. For all lamps listed in Clause 5, data sheets are contained in this standard or included by reference. For other lamps, the relevant data are supplied by the lamp manufacturer or responsible vendor. It could be based on national legislation.

Lamps for road vehicles - Dimensional, electrical and luminous requirements; Amendment 5

SAE J587-2012 牌照照明设备(后牌照照明设备)

This SAE Standard provides test procedures, requirements, and guidelines for vehicular license plate illumination devices.

License Plate Illumination Devices (Rear Registration Plate Illumination Devices)

SAE J387-2012 机动车照明用术语

This SAE Recommended Practice provides definitions of common terms used in SAE Documents pertaining to motor vehicle lighting. It covers not only basic lighting terms but also terms which identify major segments of technical reports.

Terminology Motor Vehicle Lighting

SAE J575-2012 总体宽度小于2032mm的机动车辆用照明装置及元件的试验方法和设备

This SAE Recommended Practice is intended as a quide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provided standardized laboratory tests, test methods and equipment, and requirements for lighting devices covered by SAE Recommended Practices and Standards. It is intended for devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in SAE J2139. Device specific tests and requirements can be found in applicable SAE technical reports.

Test Methods and Equipment for Lighting Devices for Use on Vehicles Less Than 2032 mm in Overall Width

BS ISO 13207-1:2012 道路车辆.用于灯泡兼容性故障检测的发光二极管(LED)灯泡特征.指示方向的发光二极管(LED)灯泡

Road vehicles. LED lamp characteristics for bulb compatible failure detection. LED lamps used as direction indicators

SAE J759-2012 照明识别代码

This SAE Recommended Practice provides the lighting function identification codes for use on all passenger vehicles, trucks, trailers, motorcycles, and emergency vehicles.

Lighting Identification Code

SAE J2938-2012 LED灯源试验和要求标准.第2部分.LED流明度和颜色维护测量

This SAE Recommended Practice provides test procedures, requirements, and guidelines for the methods of the measurement of lumen maintenance of LED devices (packages, arrays and modules). This document does not provide guidance or make any recommendation regarding predictive estimations or extrapolation for lumen maintenance beyond the limits of the lumen maintenance determined from actual measurements.

LED Light Sources Tests and Requirements Standard; Part 2: LED Lumen and Color Maintenance Measurements

SAE J3003-2012 一般用途密封照明装置的尺寸规范

This SAE Recommended Practice provides dimensional specifications for the 114mm (4 1/2 inch) and 146mm (5 3/4 inch) general service sealed lighting units, intended for use in such applications as motorcycle headlamps, military headlamps, industrial machinery headlamps, fog lamps, spot lamps, etc. This document supersedes SAE J 760.

Dimensional Specifications for General Service Sealed Lighting Units

ISO 13207-1:2012 道路车辆.用于灯泡兼容性故障检测的发光二极管灯灯泡特征.第1部分: 指示方向的发光二极管灯灯泡

Road vehicles - LED lamp characteristics for bulb compatible failure detection - Part 1: LED lamps used as direction indicators