T61 拖拉机 标准查询与下载

BS ISO 23205:2006 农业拖拉机.驾驶员坐位

ISO 23205:2006 specifies the minimum design and performance requirements for an instructional seat and restraint designed for limited use by a trainer, trainee or service person inside the enclosed cab of an agricultural tractor.

Agricultural tractors - Instructional seat

ISO/OECD 789-10:2006 农业拖拉机.试验程序.第10部分:拖拉机/器具接口的液压功率

ISO/OECD 789-10 specifies tests for determining the hydraulic pressure at the external hydraulic service of an agricultural tractor/implement as specified in ISO 10448, as well as companion tests for measuring the maximum hydraulic power available.

Agricultural tractors - Test procedures - Part 10: Hydraulic power at tractor/implement interface

KS B 7853-2005 农业拖拉机旋转性能试验方法

이 규격은 타이어를 장착한 2개 이상의 차축을 가진 차륜형과 궤도형 농업용 트랙터의 최 소

Testing method for turning area and turning circle of agricultural tractors

KS B 7943-2005 农业用挂车的试验方法

이 규격은 농업용 트레일러의 성능 시험 방법에 대하여 규정한다.

Testing method for agricultural trailers

KS B 7941-2005 农用拖拉机三点支撑装置用球的主要尺寸

이 규격은 농업용 트랙터에 사용하는 구형 간의 퀵 커플러 볼 부싱의 주요 치수에 대하여 규

Dimensions of ball used to 3 point linkage for agricultural tractors

KS B 7942-2005 农用拖拉机用犁铧尺寸

이 규격은 농업용 트랙터용 이랑쟁기의 보습에 대하여 적용한다.

Dimensions of share of furrow oriental plow for agricultural tractors

KS B 7940-2005 动力插秧机试验方法

이 시험 방법은 토부묘를 사용하는 동력 이앙기(이하 “공시기”라 한다.) 시험에 대하여 적

Test method for paddy plating machine

JB/T 10495-2005 皮带传动轮式拖拉机.通用技术条件

本标准规定了皮带传动轮式拖拉机的通用技术要求、试验方法、检验规则、交货、标志、运输及贮存等。 本标准适用于皮带传动轮式拖拉机(以下简称拖拉机)。其他拖拉机亦可参照执行。

Specifications for belt-driven wheeled tractors

KS B 7807-2004 农业拖拉机离合器摩擦片

이 규격은 농업용 트랙터의 건식 단판 클러치 디스크(이하 클러치 디스크라 한다.)에 대하여

Clutch disk assemblies for agricultural tractors

KS B 7805-2004 农业拖拉机离合联轴节

이 규격은 농업용 트랙터의 건식 클러치 페이싱(이하 클러치 페이싱이라고 한다.)에 대하여

Clutch pacing assemblies of agricultural tractors

KS B 7806-2004 农业拖拉机离合器盖

이 규격은 농업용 트랙터의 건식 단판 클러치 디스크 커버(이하 클러치 커버라 한다.)에 대

Clutch cover assemblies of agricultural tractors

JB/T 6712-2004 拖拉机外观质量要求

本标准规定了拖拉机外观质量的技术要求。 本标准适用于拖拉机。

Tractor appearance quality

JB/T 9758-2004 气缸套、活塞环快速模拟磨损.试验方法

　　本标准规定了气缸套、活塞环的快速模拟磨损试验规范。 　　本标准适用于气缸直径为85mm～135mm的内燃机气缸套、活塞环室外内快速模拟磨损试验（其他缸径可参照本标准执行）。

Fast simulation test procedure for cylinder liners and rings

ISO 500-2:2004 农用拖拉机.后置式动力输出1、2、3型.第2部分:窄轮距拖拉机主挡板和余隙的尺寸

This part of ISO 500 specifies the dimensions of the master shield and clearance zones for rear-mounted power take-offs (PTO) of types 1 and 2 on narrow-track (track width 1 150 mm or less) agricultural tractors.

Agricultural tractors - Rear-mounted power take-off types 1, 2 and 3 - Part 2: Narrow-track tractors, dimensions for master shield and clearance zone

JB/T 7282-2004 拖拉机用油品种、规格的选用

本标准规定了拖拉机用油品种、规格的选用。 本标准适用于拖拉机。农用运输车可参照采用。

Type and specifications of oil for tractors

CSA M730-1-04-CAN/CSA-2004 农业轮式拖拉机—后置式三点悬挂装置.第1部分:1、2、3和4类.第1版本

The Canadian Standards Association, which operates under the name CSA International (CSA), under whose auspices this National Standard has been produced, was chartered in 191 9 and accredited by the Standards Council of Canada to the National Standar

Agricultural wheeled tractors - Rear-mounted three-point linkage - Part 1: Categories 1, 2, 3 and 4 First Edition

ISO 500-3:2004 农用拖拉机.后置式动力输出1、2、3型.第3部分:主PTO尺寸和PTO的花键尺寸及位置

This part of ISO 500 specifies manufacturing requirements for, and the location of, rear-mounted power take-offs (PTOs) of types 1, 2 and 3 on agricultural tractors.

Agricultural tractors - Rear-mounted power take-off types 1, 2 and 3 - Part 3: Main PTO dimensions and spline dimensions, location of PTO

ISO 500-1:2004 农用拖拉机.后置式动力输出1、2、3型.第1部分:主挡板和余隙的一般规范、安全要求和尺寸

This part of ISO 500 gives general specifications, including speeds, safety requirements, the dimensions for the master shield and clearance zones for rear-mounted power take-offs (PTOs) of types 1, 2 and 3 on agricultural tractors with a track setting of more than 1 150 mm (those with a track setting width of 1 150 mm or less are covered in ISO 500-2).

Agricultural tractors - Rear-mounted power take-off types 1, 2 and 3 - Part 1: General specifications, safety requirements, dimensions for master shield and clearance zone

ASME B30.14-2004 带侧置起重臂的拖拉机

Volume B30.14 includes provisions that apply to the construction, installation, operation, inspection, testing, and maintenance of side boom tractors powered by an internal combustion engine used for pipe laying or lifting operations, utilizing a lifting boom, drum, wire rope, and/or hydraulic cylinders. The requirements for a side boom tractor that is used for other than lifting operations such as when converted for excavating work, and a side boom tractor with a rated load of one ton or less, are not included in this Volume.

Side Boom Tractors

KS B 7937-2003 农用拖拉机PTO动力传动轴的十字轴颈装配的尺寸

이 규격은 농업용 트랙터용 PTO 동력 전달 축의 유니버설 조인트에 사용되는 십자 저널

Dimensions of journal cross-assembly for PTO drive shafts of agricultural tractors