U47 舱室辅机 标准查询与下载
共找到 205 条与 舱室辅机 相关的标准，共 14 页
本标准规定了水面舰船用滑油、淡水冷却器（以下简称冷却器）的要求、质量保证规定和交货准备等。 本规范适用于设计压力不大于2.5MPa，设计温度不高于150℃，冷却介质为海水或低温淡水，工作介质为滑油、淡水的管壳式冷却器的设计、制造及验收。
Specification for lube oil & fresh water cooler of ships
- ICS
- 47.020.20
- CCS
- U47
- 发布
- 2005-12-12
- 实施
- 2006-05-01
이 규격은 선박의 내연 기관에 사용하는 배기 가스 이용에 따른 소형 연료유 가열기(이하 가
Ships small size fuel oil heaters
- ICS
- 47.020.90
- CCS
- U47
- 发布
- 2005-09-23
- 实施
- 2005-09-23
This SAE Recommended Practice provides guidance defining the hydraulic system requirements and forpreparing a detailed specification for a pumping component. The user can follow this document to setforth the pump environmental and performance considerations, establish service life and reliability goals,and define specific evaluation tests in order to qualify it for advanced marine vehicle applications.1.1 PurposeThe application of aerospace technology to marine vehicle systems has generated the need for morerigorous system designs and detailed specifications of components. This Recommended Practice isintended to aid in the system design process and in the preparation of a specification for a hydraulicpump to be used on advanced surface craft and submersible vehicles.1.2 Rationale1.2.1 CHANGES IN THIS REVISIONThis document has been extensively revised and changed from an information report to a recommendedpractice. Many military specifications and standards have been deleted or replaced with industrystandards. Several new references have been added. Because of the extent of the revisions it isimpractical to list each individual change.1.2.2 RELATIONSHIP OF SAE STANDARD TO ISO STANDARDNo equivalent ISO document exists.
Marine Vehicles-Hydraulic Pumps-Design and Specification Guide
- ICS
- 23.100.10;47.020.50
- CCS
- U47
- 发布
- 2005-05-13
- 实施
- 2014-02-25
本规范规定了舰载雷达密闭式电子机柜专用空调机组（以下简称“空调机”）的技术要求、质量保证规定和交货准备等。 本规范适用于额定送风量不高于700Om/h岛的空调机。其他雷达密闭式电子机柜专用空调机组亦可参照使用。
The specification for special-purpose air-conditioning units of shipborne radar airtight cabinet
- ICS
- CCS
- U47
- 发布
- 2005-04-11
- 实施
- 2005-07-01
本标准规定了船用滑油冷却器、淡水冷却器、蒸汽冷凝器、燃油加热器、滑油加热器、淡水加热器的强度计算和热工计算方法。 本标准适用于设计压力不大于3.0 MPa，介质温度不超过250℃的壳管式热交换器。
Calculation method for design of marine heat exchanger
- ICS
- 47.020.90
- CCS
- U47
- 发布
- 2004-02-16
- 实施
- 2004-06-01
1.1 This specification covers mechanical end-face seals for centrifugal and positive displacement pumps for shipboard use.1.2 The following types of seals are not included in this specification: lip seals, oil seals, circumferential seals, or labyrinth seals.1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. A companion hard metric standard is in the process of preparation.1.4 Special requirements for U.S. Navy Shipboard Pump Applications are included in Supplement S1.
Standard Specification for Mechanical Seals for Shipboard Pump Applications
- ICS
- 47.020.30 (Piping systems)
- CCS
- U47
- 发布
- 2004
- 实施
1.1 이 규격은 액화 가스 운송에 사용되는 구형 탱크의 내부 측정을 위한 입체 사진
Refrigerated light hydrocarbon fluids-Calibration of spherical tanks in ships-Part 1:Stereo-photogrammetry
- ICS
- 75.180.30
- CCS
- U47
- 发布
- 2003-12-20
- 实施
- 2003-12-20
Refrigerated light hydrocarbon fluids-Calibratio
Refrigerated light hydrocarbon fluids-Calibration of spherical tanks in ships-Part 2:Triangulation measurement
- ICS
- 75.180.30
- CCS
- U47
- 发布
- 2003-12-20
- 实施
- 2003-12-20
? ??? ?? ???? ???? ?? ?? ?? ??? ?, ?? ??? ??? ??
Coiled springs for marine machinery
- ICS
- 47.020.20
- CCS
- U47
- 发布
- 2003-07-12
- 实施
- 2003-07-12
1.1 This specification covers mechanical end-face seals for centrifugal and positive displacement pumps for shipboard use.1.2 The following types of seals are not included in this specification: lip seals, oil seals, circumferential seals, or labyrinth seals.1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. A companion hard metric standard is in the process of preparation.1.4 Special requirements for U.S. Navy Shipboard Pump Applications are included in Supplement S1.
Standard Specification for Mechanical Seals for Shipboard Pump Applications
- ICS
- 47.020.30 (Piping systems)
- CCS
- U47
- 发布
- 2003
- 实施
本标准规定了船用卧式自吸离心旋涡泵的分类、要求、试验方法、检验规则和标志、包装、运输及贮存。 本标准适用于输送供船舶饮水、洗涤和卫生装置用淡水及海水(介质温度不高于75℃)的泵的设计、制造与验收。
Marine horizontal self-priming centrifugal-vortex pumps
- ICS
- 47.020.20
- CCS
- U47
- 发布
- 2002-11-20
- 实施
- 2003-02-01
1.1 This specification covers the requirements applicable to the design and construction of centrifugal pumps for shipboard application. The three classes of service covered by this specification are as follows:1.1.1 Class 18212;Freshwater,1.1.2 Class 28212;Seawater, and1.1.3 Class 38212;Hydrocarbon pumps (less than 1500 SSU).1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.
Standard Specification for Centrifugal Pump, Shipboard Use
- ICS
- 23.080 (Pumps)
- CCS
- U47
- 发布
- 2002
- 实施
本标准规定了海军9?K10-3 空气压缩机的修理勘验范围、修换技术标准、试验验收要求和修理后提交的文件。 本标准适用于海军3 K10-3 空气压缩机的计划修理。 临时修理可参照执行。 对3 K10-2,3 K7.5-2 空气压缩机的修理亦可参照。 2 引用标准
Navel technical standard for repairing эк 10-3 air compressor
- ICS
- CCS
- U47
- 发布
- 2001-12-18
- 实施
- 2001-12-20
本标准规定了船用蒸汽散热器的分类、要求、试验方法、检验规则、包装、贮存等。 本标准适用于其介质为饱和水蒸汽、介质设计压力不大于0.45 MPa的各类船舶暖气系统的散热器的设计、制造、检验与验收。
Marine steam radiator
- ICS
- 47.020.90
- CCS
- U47
- 发布
- 2001-11-15
- 实施
- 2002-02-01
Ships and marine technology - Heading control systems; Technical Corrigendum 1
- ICS
- 47.020.70
- CCS
- U47
- 发布
- 2001-11
- 实施
本标准规定了水力驱动驱气风机的分类、要求、试验方法、检验规则、标志、包装和贮存等。 本标准适用于船舶危险区域清舱及消防系统用水力风机的设计、制造和验收。
Gasfreeing fans with water motor
- ICS
- 47.020.90
- CCS
- U47
- 发布
- 2000-09-20
- 实施
- 2001-01-01
1.1 This specification covers the requirements applicable to the design and construction of centrifugal pumps for shipboard application. The six classes of service covered by this specification are as follows:1.1.1 Class 1--Boiler feedwater and other freshwater applications with temperatures above 212oF (100oC),1.1.2 Class 2--Condensate water,1.1.3 Class 3--Freshwater except Classes 1 and 2,1.1.4 Class 4--Seawater in which total head produced per stage does not exceed 50 psi (345 kPa),1.1.5 Class 5--Seawater in which total head produced per stage exceeds 50 psi (345 kPa), and1.1.6 Class 6--Hydrocarbon pumps (less than 1500 SSU).1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.
Standard Specification for Centrifugal Pump, Shipboard Use
- ICS
- 23.080 (Pumps)
- CCS
- U47
- 发布
- 2000
- 实施
MIL-P-17454B Interim Amendment 2, dated 14 November 1966, is hereby reinstated through 31 December 2000 and may be used for acquisition. If MIL-P-17454B has not been revised or amended by 31 December 2000, Interim Amendment 2 will be canceled.
PUMP, CENTRIFUGAL, PORTABLE, SUBMERSIBLE
- ICS
- CCS
- U47
- 发布
- 1999-09-20
- 实施
本标准规定了船用高压(16 MPa)双作用叶片泵的分类和标记、技术要求、试验方法和检验规则。 本标准适用于以矿物油为工作介质的船用高压双作用叶片泵的设计、生产和验收。
Double acting high-pressure vane pump for ship
- ICS
- 47.020.20
- CCS
- U47
- 发布
- 1999-04-30
- 实施
- 1999-08-01
本标准规定了船用中压(6.3 MPa)双作用叶片泵的分类和标记、技术要求、试验方法和检验规则。 本标准适用于以矿物油为工作介质的船用中压双作用叶片泵的设计、生产与验收。
Double acting mid-pressure vane pump for ship
- ICS
- 47.020.20
- CCS
- U47
- 发布
- 1999-04-30
- 实施
- 1999-08-01
